Turnstiles KT-2 Quick Start Manual

KT-2 Two-Door Controller Quick Start Guide

Before you begin

Before you install the controller, check that the product box
contains the following items:
• One KT-2 Two-Door Controller
• One accessories kit
• KT-2 Two-Door Controller Installation Guide

Operating modes

Use the KT-2 controller in one of the following modes:
• Stand-alone mode: use as a stand-alone controller with direct
configuration. This does not require any software.
• EntraPass mode: use with EntraPass access control software to
connect to additional doors and controllers.

Installing and powering the KT-2

Power the KT-2 in one of the following ways:
• Use power over Ethernet (PoE).
• Use power over Ethernet plus (PoE+).
• Connect an external power supply to the 12 VDC input.
To install and power the KT-2, refer to the Installation and Powering
the KT-2 sections of the KT-2 Two-Door Controller Installation Guide.

Connection and configuration

Wired controller

1. To connect the controller, refer to the KT-2 Two-Door Controller
Installation Guide.
2. To configure the controller, complete
using the registration page.

Wireless controller

• To connect and configure the controller, complete
and configuring a wireless controller.

Configuring the KT-2 using the registration page

1. Connect the controller to your preferred network using the
Ethernet port.
2. On your computer or mobile device, open a web browser.
Note: If you use a mobile device, connect it to a wireless
network that has access to the wired network subnet.
D29010686R001
D29010686R001
3. In the address bar, type one of the following options:
- Type the IP address of the KT-2 controller. This is the
preferred option. To find the controller's IP address, you
can use the KT-Finder.
- Type KT-XX-XX-XX where XX-XX-XX is the last six digits of
the controller's Ethernet MAC address.
Note: The KT-2 controller and the device you use to
access the registration page must be on the same
network. If either of the devices are behind a bridged
network, even if they have the same subnet, this cannot
work.
4. On the KT-2 REGISTRATION page, in the upper right of the
window, select your preferred language. English is selected by
default.
5. To configure the correct mode, complete the steps in one of
the following procedures:
- To configure the controller in stand-alone mode,
complete one of the following options:
- To configure the controller in EntraPass mode, complete
Configuring EntraPass mode for a wired
Configuring stand-alone mode using the activate now
option
Configuring the KT-2
1. On the KT-2 REGISTRATION page, click Activate now.
2. On the Activate now tab, in the Customer information and
Installer information fields, type the relevant information.
Connecting
3. Click Activate now.

Configuring stand-alone mode using an activation code

1. Go to http://www.kantech.com.
2. Click Support and click Kantech Registration.
3. In the KT Standalone Registration area, click Click here.
www.TURNSTILES.us | EntraPASS.com | patrick.mcallister@TURNSTILES.us | 303-670-1099
- Configuring stand-alone mode using the activate
now option
- Configuring stand-alone mode using an
activation code
controller.
4. On the KTWeb - Registration page, type the relevant
information and click Register. You receive an activation code
by email. Alternatively, contact Kantech technical support in
your region to get an activation code.
5. Go to the KT-2 REGISTRATION page and click Other ways to
activate.
6. In the Activation code field, type the activation code, and
click Activate now.

Configuring EntraPass mode for a wired controller

1. On the KT-2 REGISTRATION page, click EntraPass.
2. In the EntraPass gateway pane, in the IP address field, type
the IP address, or in the Domain name field, type the domain
name.
3. From the Protocol list, select TCP or UDP.
4. Optional: If you select UDP, in the Port field, type the port
number.
5. Click Submit.

Connecting and configuring a wireless controller

You can connect the KT-2 over Wi-Fi only when you use the
controller in EntraPass mode and power it with a KT-PS4085 power
supply.
1. On a laptop or mobile device, go to the Wi-Fi settings.
2. From the list of available wireless networks, select the access
point (AP) name (SSID) of the controller. The AP name of the
controller appears as KT2-XX-XX-XX. XX-XX-XX represents
the last six digits of the AP MAC address printed on the KT-2
backplane label.
3. Clear the Connect automatically check box and click
Connect.
4. In the Enter the network security key field, type the
password. The default password is TYCO1234.
5. Click Next and check your connection status.
6. On a web browser address bar, type the following IP address:
192.168.240.1/jciprov.html. Press Enter.
7. On the Web Provisioning page, from the Please Select
Country list, select a country.
2021-06-28