Advertisement
Quick Links
Advertisement
Summary of Contents for Idex Knight Trak II KTL-6503
- Page 1 Knight Trak II Instruction Manual 0901039 Rev: C (05/01) Page 1 of 16...
- Page 2 Drawing-System Wiring Diagram ............. 3 Knight Trak II System Overview ............... 4 Drawing-POB Wiring ................8 Drawing-LFP Wiring ................. 9 Drawing-Control Connections for Multilinking ......... 10 The Signal Input Board (SIB) ..............11 Drawing-SIB Connection ................ 12 The Management Input Board (LMIB) ............ 13 Network wiring Diagram .................
- Page 3 0901039 Rev: C (05/01) Page 3 of 16...
- Page 4 The Knight-Trak II Data Management System represents the “Next generation” of laundry dispensing equipment with data tracking capability. On-site programming, centralized control, and the ability to export information to personal computers are just a few of the many enhancements provided by Knight- Trak II.
- Page 5 (1) Remove the locking cover panel from the pump housing using the key provided. (2) Mount pump housing in a convenient location on a wall near supply containers. This location is usually near the laundry machine, however, can be mounted as a remote pumping system. Use proper mounting hardware and utilize appropriate mounting techniques for various types of walls (i.e.
- Page 6 Multilinking is a way to connect multiple Knight-Trak II dispensers in a laundry. Once connected, you can "talk" to all dispensers from a single connection. (1) Before connecting the multilinking cable, use the LFP to give each dispenser its own ID number. If dispensers on the multilink have the same ID number, they will not work correctly.
- Page 7 (1) Measure the distances from chemical supply container to pump housing and from pump housing to injection point inside the washmachine. (2) Insert one end of a suction tube into the left side of the squeeze tube in the leftmost peristaltic pump. (3) Cut the suction tube to length and insert other end into supply container using PVC pipe as a support.
- Page 8 Page 8 of 16 0901039 Rev: C (05/01)
- Page 9 0901039 Rev: C (05/01) Page 9 of 16...
- Page 10 Page 10 of 16 0901039 Rev: C (05/01)
- Page 11 The Knight-Trak Signal Input Board (SIB) is an interface module which receives pump activation signals of 14 to 240 Volts from the washmachine and sends them as low-voltage data signals to the Knight-Trak II Dispenser. The module is available in 6, or 10 pump configurations. The SIB should be installed in the washer near the supply signal outputs (1) Inspect the wiring diagram for the laundry machine (and card reader, if required).
- Page 12 Page 12 of 16 0901039 Rev: C (05/01)
- Page 13 The Knight-Trak II Laundry Management Input Board (LMIB) is an interface module which receives wash tracking information signals from the washmachine and sends them as low-voltage signals to the Knight-Trak II Dispenser. The module is connected to a Knight-Trak II Signal Input Board (SIB). THE LMIB IS TO BE INSTALLED BY CERTIFIED ELECTRICAL PROFESSIONALS ONLY.
- Page 14 Page 14 of 16 0901039 Rev: C (05/01)
- Page 15 Data Flow 3 CONDUCTOR NETWORK CABLE Over Multi-Link KNIGHT P/N 0300058 ONLY Multi-Link Terminals CONNECT THE PLUG INTO THE JACK ON THE CIRCUIT BLACK TERMINAL BOARD IN ANY ONE OF THE MULTI-LINKED DISPENSERS. BROWN TERMINAL POB Circuit Board 3 CONDUCTOR NETWORK CABLE KNIGHT P/N 0300058-X ONLY (X = LENGTH OF CABLE) 12 VDC...
- Page 16 Warranty does not cover liability resulting from performance of this equipment nor the labor to replace this equipment. Product abuse or misuse voids warranty. A Unit of IDEX Corporation .1,*+7 ,1& World Headquarters:...