Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Encore ENRXWI-SG
Summary of Contents for Encore ENRXWI-SG
- Page 1 108M 802.11g Wireless LAN Access Point User Guide...
- Page 2 Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones.
-
Page 3: Fcc Interference Statement
FCC Radio Frequency Exposure statement This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far below the FCC radio frequency exposure limits. -
Page 4: Safety Information
Safety Information Your device contains a low power transmitter. When device is transmitted it sends out radio frequency (RF) signal. CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. -
Page 5: Table Of Contents
TABLE OF CONTENT About This Guide... 1 Purpose ... 1 Overview of this User’s Guide ... 1 Unpacking and Setup ... 2 Unpacking ... 2 Setup... 2 Hardware Instalation ... 3 LED Indicator... 3 Rear Panel... 3 Hardware connections ... 4 Connect to the Switch/Hub ... -
Page 6: About This Guide
ABOUT THIS GUIDE Congratulations on your purchase of this 108M Super-G Wireless LAN Access Point. This manual helps to features the innovating wireless technology that can help you build a wireless network easily! This manual contains detailed instructions in operation of this product. Please keep this manual for future reference. With a WLAN Access Point, a mobile computer can share data with another mobile computer in a wireless way. -
Page 7: Unpacking And Setup
UNPACKING AND SETUP This chapter provides unpacking and setup information for the Access Point. Unpacking Open the box of the Access Point and carefully unpack it. The box should contain the following items: One Wireless Access Point One Antenna One external power adapter One CD-Rom (User’s guide) If any item is found missing or damaged, please contact your local reseller for replacement. -
Page 8: Hardware Instalation
HARDWARE INSTALATION LED Indicator The figure below shows the LED Indicator of the Wireless LAN Access Point. Power This indicator lights green when the Access Point receives power. Otherwise, it turns off. LAN (Link/ACT) The indicator lights green when the LAN port is connected to Ethernet network, the indicator blinks green while transmitting or receiving data on the Ethernet network. -
Page 9: Hardware Connections
Ethernet Ethernet uplink port with auto-sensing for connecting to either 10/100Mbps Fast Ethernet connections, connect this port to switch/hub. Reset To reset the setting back to factory default setting, press the “Reset” button 3 seconds, once you press the button, the LED of the WLAN will turn off and when the Access Point is ready, the LED will start blinking. -
Page 10: Connect To The Switch/Hub
Connect to the Switch/Hub 1. Plug in one end of the RJ45 network cable to the Switch/Hub port, 2. Plug in the other end of the RJ45 network cable to the Wireless Access Point. Check the installation The control LEDs of the Access Point are clearly visible and the status of the network link can be seen instantly: 1. -
Page 11: Configuring The Wireless Lan Access Point
CONFIGURING THE WIRELESS LAN ACCESS POINT The Wireless Access Point has a Web GUI interface for the configuration. The AP can be configured through the Web Browser. A network manager can manage, control and monitor the AP from the local LAN. This section indicates how to configure the AP to enable its functions. -
Page 12: Quick Setup With Wizard
Quick Setup with Wizard Setup wizard is provided as the part of the web configuration utility. You can simply follow the step-by-step process to get your Access Point configuration ready to run in 4 easy steps by clicking on the “Wizard” button on the function menu. The following screen will appear. - Page 13 Step2: Set WLAN Connection Please type the name of SSID you like and select the channel. Then, click “Next” to continue. Figure 8. Setup Wizard – Set Wireless LAN Connection Step 3: Set WEP Encryption If you like to enable WEP, please click “Enabled”. Then, select the key size of WEP encryption and enter the key value in the key text box.
-
Page 14: Configuration Through Web Browser
Step 4: Restart The Setup wizard is now completed. The new settings will be effective after the Access Point restarted. Please click “Restart” to reboot the Access Point. If you do not want to make any changes, please click “exit” to quit without any changes. You also can go back to modify the setting by clicking “Back”. -
Page 15: Status
Status The Status Function shows the System, Wireless Configuration and TCP/IP Configuration status and some settings of the Access Point. Figure 12. Status Firmware Version: Shows the current firmware version. LAN: Shows the Mac address, IP address (default: 192.168.1.1), Subnet Mask, Gateway Address. -
Page 16: Basic Setting
View Log: Upon clicked, the page will change to log page. The log page records every event and the time that it happens. Figure 13. View Log You may clear the entries recorded in the log by clicking the “Clear Log” button, and refresh the screen to show the latest log entries by clicking the “Refresh”... - Page 17 AP Name: appoint a name for the AP. SSID: It is an ASCII string up to 32 characters used to identify a WLAN that prevents the unintentional merging of two co-located WLANs. The SSID value must be the same in all stations and AP in the extended WLAN. Wireless Channel: There are 14 channels available.
-
Page 18: Ip Setting
IP Setting This page allows you to configure the IP and DHCP settings of the Access Point. Figure 16. IP Setting The default IP address of this access point is 192.168.1.1 with the subnet mask of 255.255.255.0. You can type in other values for IP Address, Subnet Mask and Gateway and click “Apply”... -
Page 19: Advanced Setting
Advanced Setting This page contains configurations for advanced users, which the change reflects, the wireless performance and operating modes. AP Mode: Select one of the AP operating modes for different application of Access Point. AP mode – The normal Access Point operating mode which forms a wireless ESS network with its wireless clients. - Page 20 Wireless Bridge mode – A pair of APs operating under Bridge mode to act as the bridge that connect two Ethernet networks or Ethernet enabled clients together. You must make sure that the SSID and Channel is set the same as that AP you wish to connect.
- Page 21 CTS Mode (clear to send): None- disable CTS function. Always- Regardless of wireless environment (11b or 11g), platform will always transfer 11g packet. Auto- AP soon detected the wireless environment and decided the transmission packet, either 11b or 11g. WDS (Wireless Distribution System): Only use in AP mode. It will add client quantity at the back when you enable this function.
-
Page 22: Security
Security This page is where you configure the security features supported by this Access Point. Password: Allow you to change the new login password. necessary steps: 1. Enter the new password in the “AP Password New:” field. Enter 3. Click “Apply” MAC Filter: MAC Filter function controls the MAC of the network devices that are listed in this table for access authorization or denial. -
Page 23: Tools
Tools Four functions are provided in this page, Backup, Restore Settings, Restore default settings and Firmware Upgrade. Figure 19. Tools Backup Settings: Click on “Backup” button, which will open a FileSave Dialog box, where you get to save all the current settings and configurations to a file. -
Page 24: Technical Specifications
TECHNICAL SPECIFICATIONS Standards Signal Type: Modulation: LED Indicators: Frequency Range Frequency Band: Channel: Data Encryption: Data Transfer Rate Receiver Sensitivity Transmit Rate Transmission Range: Antenna: General IEEE 802.11b Wireless LAN, IEEE 802.11g Wireless LAN IEEE 802.3u Fast Ethernet 802.11b: DSSS, 802.11g:OFDM QPSK / BPSK / CCK / OFDM Power, LAN (Link/Activity), WLAN (Activity) 2412 ~ 2484 MHz ISM band (channels 1 ~ 14) - Page 25 DC inputs Temperature Humidity Dimensions EMI: Physical and Environmental 5VDC /2A or higher current Operating: 0° ~ 40° C, Storage: -10° ~ 70° C Operating: 10% ~ 90%, Storage: 5% ~ 90% 146 x 113 x 41 mm (W x H x D) without Antenna FCC Class B, CE Mark B,...