Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for extronics iTAG100-7
Summary of Contents for extronics iTAG100-7
- Page 1 Operating Manual iTAG100-7, iTAG100-7-CB iTAG100-7D, iTAG100-7D-CB...
- Page 2 (See DDM for the latest Version) For warranty information, refer to Terms and Conditions at http://www.extronics.com ©2020 Extronics Limited. This document is Copyright Extronics limited. Extronics reserve the right to change this manual and its contents without notice, the latest version applies.
-
Page 3: Table Of Contents
Contents Introduction ......................4 Safety Information and Notes ................5 Storage of this Manual ................... 5 Special Conditions for Safe Use ..............5 2.1.1 Class I Zone 0 ..................5 2.1.2 Class I Zone 1 ..................5 2.1.3 Class II Zone 21 ..................5 List of Notes .................... -
Page 4: Introduction
1 Introduction The iTAG100-7, iTAG100-7-CB, iTAG100-7D, iTAG100-7D-CB are MET Canada approved, intrinsically safe versions of the Stanley T2 Tag. This is the most advanced Wi-Fi based Active RFID tag on the market, from the company that originated the Wi-Fi tag industry. The device is a small, long-life Wi-Fi based active RFID device that can be placed on any asset, allowing the Stanley system to locate assets that are not Wi-Fi enabled. -
Page 5: Safety Information And Notes
2 Safety Information and Notes 2.1 Storage of this Manual Keep this user manual safe and in the vicinity of the product. All persons required work on or with the product should be advised on where the manual is stored. 2.1 Special Conditions for Safe Use 2.1.1 Class I Zone 0 None... -
Page 6: Class And Zone Approval Information
Any repairs or replacement of parts MUST be performed by the manufacturer or its nominated sub-contractor or agent. 2.3 Class and Zone Approval Information The iTAG100-7, iTAG100-7-CB carry the following approval: MET Canada Class I, Zone 0, Ex ia IIB T6..T4 Ga Class I, Zone 1, Ex ia IIC T6..T4 Gb... -
Page 7: Installation And Setting-To-Work
3 Installation and Setting-to-Work 3.1 Assembly and Disassembly The iTAG100 is provided ready assembled and should not be dismantled by the user. 3.2 Installation The iTAG100 should be mounted on the asset to be tracked, or worn by the person who is to be tracked. -
Page 8: Intended Purpose Usage
4 Intended Purpose Usage Important Before setting the units to work, read the technical documentation carefully. Important The latest version of the technical documentation or the corresponding technical supplements is valid in each case. Important For the installation, maintenance and cleaning of the units, it is absolutely necessary to observe the applicable regulations and provisions concerned with explosion protection (IEC 60079-0, IEC 60079- 11, IEC 60079-14, CEC 18). -
Page 9: Cleaning And Maintenance Intervals
The iTAG100 will require additional protection if it is installed in a location where it may be subjected to damage. 5 Type Codes Type Code Description iTAG100-7 MET Canada Certified, Class I Zone 0 IIB T4,T5,T6, Listing E113811 Class I Zone 1 IIC T4,T5,T6, Listing E113811 iTAG100-7-CB... -
Page 10: Manufacturer
6 Manufacturer The iTAG100 is manufactured by: Extronics Ltd, 1 Dalton Way, Midpoint 18, Middlewich Cheshire CW10 0HU Tel. +44(0)845 2775000 Fax. +44(0)845 2774000 E-mail: info@extronics.com Web: www.extronics.com 7 Radio Equipment – FCC Warning Statement FCC warning statement: • This device complies with Part 15 of the FCC Rules. -
Page 11: Label Drawings
8 Label Drawings Notes 1 Additional marking if required 2 Optional logos here...
Need help?
Do you have a question about the iTAG100-7 and is the answer not in the manual?
Questions and answers