Related Manuals for MAKINEX GEN-10P
Summary of Contents for MAKINEX GEN-10P
- Page 1 10kVA Generator GEN-10P -2x15A Outlets -2x15A + 1x20A (or 32A) 3P Outlets OPERATOR’S MANUAL Rev0919...
-
Page 2: Table Of Contents
Table of Contents INTRODUCTION ............................... 1 DISCLAIMER ..............................1 ABOUT THIS MANUAL ............................2 KEY TERMS ................................2 PRODUCT INFORMATION ..........................3 SAFETY INFORMATION ............................3 SAFETY DECALS ..............................6 PRODUCT SPECIFICATIONS ..........................7 FEATURES................................7 OVERALL MACHINE DIMENSIONS ........................8 ALTERNATOR SPECIFICATIONS ........................... -
Page 3: Introduction
Thank you for purchasing a MAKINEX product. This manual provides information and procedures to safely operate and maintain the GEN-10P Generator. For your own safety and protection from injury, carefully read, understand and observe the safety instructions described in this manual. -
Page 4: About This Manual
DANGER – indicates a imminently hazardous situation which, if not avoided, will result in death or DANGER serious injury PROHIBITED – identifies actions that should never be carried out by anyone interacting with the machine. PROHIBITED GEN-10P – USER MANUAL REV0819 Page 2 of 22... -
Page 5: Product Information
Read this manual thoroughly before operating your generator. Failure to follow instructions could result in WARNING serious injury or death MAKINEX GEN-10P Generator designed for professional operators only, instruct operators in care WARNING and use of the machine before use! - Page 6 • ALWAYS position the generator so that the exhaust is pointing away from people or animals. • NEVER use the generator indoors or in an enclosed area. (i.e. in ware house, tunnel, well or a hold). GEN-10P – USER MANUAL REV0819 Page 4 of 22...
- Page 7 • NEVER cover or enclose the generator whilst it is in use. • Be aware of the weight of the generator, do not attempt to lift or move the generator without the assistance of other personnel or suitable lifting equipment. GEN-10P – USER MANUAL REV0819 Page 5 of 22...
-
Page 8: Safety Decals
SAFETY DECALS (9 & 10) GEN-10P – USER MANUAL REV0819 Page 6 of 22... -
Page 9: Product Specifications
2.4 L/h @ 50% LOAD FUEL TANK 6.5 L FEATURES FEATURES Durable Galvanised frame Multi cushion isolators for vibration reduction Compact design for easy storage and transport Lifting point for transportation RFL permanent magnet alternator GEN-10P – USER MANUAL REV0819 Page 7 of 22... -
Page 10: Overall Machine Dimensions
M o t o r S t a rt k V A Weight (kg) 46.5 S ho rt C ir A m ps Ref Tem p 27 ºC Serial No. RF2-132-115-135-3P-1 EC.1282.OE140328.RFLQ093 GEN-10P – USER MANUAL REV0819 Page 8 of 22... -
Page 11: Operation
This may result in an engine failure. NOTE: Refer to GX390 Manual for more in-depth instructions NOTE: New machines will be pre-oiled from MAKINEX with: Honda Power Equipment Engine Oil – SAE 10W-30, API SJ GEN-10P – USER MANUAL REV0819... - Page 12 • Wait for spilled fuel to evaporate before starting the engine. Keep fuel away from sparks, open flames, pilot lights, heat and other ignition sources. WARNING DO NOT light a cigarette or smoke near open fuel tank or container. GEN-10P – USER MANUAL REV0819 Page 10 of 22...
-
Page 13: Operating Generator
2. Turn the ignition key to the OFF position. 3. Set the fuel supply valve to OFF. NOTE: To stop the generator in an emergency simply turn the ignition key to the off position. GEN-10P – USER MANUAL REV0819 Page 11 of 22... -
Page 14: General Recommendations
Should you have questions about replacing components on your generator, please contact dealer for assistance. MAKINEX dealers have access to all the special tools, technical information, parts and training required to maintain your MAKINEX product in peak operating condition. -
Page 15: Storage
Certain storage covers can be flammable or can melt in high temperatures. DO NOT place storage cover over generator WARNING until it has completely cooled. GEN-10P – USER MANUAL REV0819 Page 13 of 22... -
Page 16: Limited Warranty
LIMITED WARRANTY In order to take advantage of the MAKINEX limited warranty, you must have maintenance performed according to the schedule (contained in relevant owner’s manual supplied with this product, e.g. Engine operator’s manual), by an authorised MAKINEX dealer or MAKINEX service technician. You are free to... -
Page 17: Warranty Exclusions
It is the consumer’s responsibility to deliver the machine in question to our service premises or to the premises of our appointed agent at the consumer’s expense for replacement or repair as applicable. Maintenance services are not covered under warranty. GEN-10P – USER MANUAL REV0819 Page 15 of 22... - Page 18 All warranties will be carried out by MAKINEX authorised staff or appointed agents at a premises to be determined by the Manufacturer. It is the responsibility (and cost) of MAKINEX or our appointed agent to return the machine to be repaired or replaced under warranty to the consumer- this is valid for domestic territories only (e.g.
-
Page 19: Contact Information
CONTACT INFORMATION For sales, service, warranty and parts for all MAKINEX products; please refer below. SALES, SERVICE, SPARE PARTS & WARRANTY SALES TEL 1300 795 953 or +61 2 9460 8071 WEB www.makinex.com.au AUSTRALIA SERVICE, SPARE PARTS & WARRANTY EMAIL service@makinex.com.au... -
Page 20: Appendices
APPENDICES APPENDIX A- WIRING CIRCUIT DIAGRAM (2x15A) APPENDIX B- WIRING CIRCUIT DIAGRAM (2x15A + 1x20A 3P) APPENDIX C- RISK ASSESSMENT GEN-10P – USER MANUAL REV0819 Page 18 of 22... -
Page 21: Appendix A- Wiring Circuit Diagram (2X15A)
APPENDIX A- WIRING CIRCUIT DIAGRAM (2x15A) GEN-10P – USER MANUAL REV0819 Page 19 of 22... -
Page 22: Appendix B- Wiring Circuit Diagram (2X15A + 1X20A 3P)
APPENDIX B- WIRING CIRCUIT DIAGRAM (2x15A + 1x20A 3P) GEN-10P – USER MANUAL REV0819 Page 20 of 22... -
Page 23: Appendix C- Risk Assessment
APPENDIX C- RISK ASSESSMENT GEN-10P – USER MANUAL REV0819 Page 21 of 22... - Page 24 GEN-10P – USER MANUAL REV0819 Page 22 of 22...