easymaxx BG-E-00192 Operating Instructions Manual page 3

EN
■ Do not insert any sharp objects into the product.
■ Protect the product from open fl ame and impacts.
■ Do not make any changes to the product and do not try to
repair it. In case of damage contact customer service. The in-
dividual LEDs cannot be replaced.
■ Never use corrosive or abrasive cleaners for cleaning. If nec-
essary, wipe the product with a damp cloth and then dry it.
■ Store the product in a dry, clean place out of reach of children
and animals.
Included in delivery
Check the product for transport damage. In case of damage do not
use the product, but contact customer service immediately.
• LED light with ventilator
• Operating instructions
2 batteries (1.5 V, type D) are also needed. These are not included
in the delivery.
Product overview
9
8
7
6
Insert / change batteries
Before inserting the batteries, check whether the contacts are
clean and clean them if needed.
1. Turn the cover (8) counterclockwise
2. Press the locking catch to the bat-
3. Remove used batteries if neces-
4. Snap the battery compartment closed. There should be an
audible click as it locks into place.
5. Set the cover on the product and
B
A
Replace the batteries if the performance is weakening.
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •
1 Handle
2 LED light on / off
switch (on / off)
1
3 Ventilator
4 Feet
2
5 LEDs
3
6 Lamp head
7 Ventilator on / off
switch (high / off / low)
4
8 Cover
9 Hook (folding)
5
and remove.
tery compartment while lifting it up.
sary, and insert two batteries (1.5 V;
type D) into the battery compart-
ment. Check the poles (+ / –) as you
insert them.
tighten by turning clockwise. Make
sure the markings on the cover (A)
and on the product (B) are on top of
one another as you set the cover on.
Customer Service / Importer:
*) Calls to German landlines are subject to your provider's charges.
Usage
The lamp head (6) can be rotated 360°.
1. Placement – The product can either be hung using the hook (9)
or, if using the ventilator without the LED light, placed on the
lamp head. Unfold the hook from the handle (1) to hang up.
2. Adjust the angle – The angle of the ventilator (3) and the lamp
head can be adjusted independently of each other. To do this,
grasp the product by the handle or the lamp head and adjust to
the desired angle by tilting the handle or lamp head.
3. Switching on – The ventilator and LED light can be switched
on independently of each other.
Ventilator: Set the on / off switch (7) to the low position for a
low power level or to the high position for a high power level.
LED light: Set the on / off switch (2) to the on position.
4. Switching off – If you no longer intend to use the ventilator
or the LED light, set the corresponding on / off switch to the
off position.
Technical data
Product number:
Model number:
Power supply:
Power:
Luminous fl ux:
Inclination:
Protection class:
Degree of protection:
Operating instructions ID: Z 08859 M DS V1 0419
Disposal
Dispose of packaging materials in an environmentally
sound way and take recyclables to collection facilities.
Remove batteries before disposing of the product and take
them to the appropriate collection site separately from the
product.
This product is subject to European Directive 2012/19/EU
on Waste Electrical and Electronic Equipment (WEEE). Do
not dispose of the product as normal household waste, but
through an offi cially approved disposal business according
to environmental regulations.
All rights reserved.
Operating Instructions
08859
BG-E-00192
3 V DC (2 x 1.5V batteries, type D)
approx. 2.3 W
approx. 22 lm
360°
III
IP44
✆
+49 38851 314650 *)