Table of Contents
Advertisement
Quick Links
FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed
and qualified in pool equipment by the jurisdiction in which the product will be installed where such
state or local requirements exist. The maintainer must be a professional with sufficient experience
in pool equipment installation and maintenance so that all of the instructions in this manual can be
followed exactly. Before installing this product, read and follow all warning notices and instructions
that accompany this product. Failure to follow warning notices and instructions may result in property
damage, personal injury, or death. Improper installation and/or operation will void the warranty.
Improper installation and/or operation can create unwanted electrical hazard which
can cause serious injury, property damage, or death.
ATTENTION INSTALLER - This manual contains important information about the
installation, operation and safe use of this product. This information should be given
to the owner/operator of this equipment.
OPERATION MANUAL
Zodiac FloPro
3-Speed Variable Pump
WARNING
INSTALLATION AND
ENGLISH
E3
Advertisement
Table of Contents
Related Manuals for Zodiac FloProE3
Summary of Contents for Zodiac FloProE3
- Page 1 INSTALLATION AND OPERATION MANUAL ENGLISH Zodiac FloPro 3-Speed Variable Pump WARNING FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist.
-
Page 2: Table Of Contents
Page 2 ENGLISH Zodiac FloPro E3 3-Speed Variable Pump Installation & Operation Manual ™ Table of Contents Section 1. Important Safety Instructions ..3 Section 5. Service and Maintenance ....8 Safety Instructions .......... 3 Routine Maintenance ........8 Pool Pump Suction Entrapment Prevention Section 6. -
Page 3: Section 1. Important Safety Instructions
Page 3 Zodiac FloPro E3 3-Speed Variable Pump Installation & Operation Manual ENGLISH ™ Section 1. Important Safety Instructions READ AND FOLLOW ALL INSTRUCTIONS Safety Instructions All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes. - Page 4 • Water temperature for test must NOT EXCEED 100°F (38°C). • Limit test to 24 hours. After test, visually check system to be sure it is ready for operation. NOTICE: These parameters apply to Zodiac equipment only. For non-Zodiac equipment, consult equipment manufacturer.
-
Page 5: Pool Pump Suction Entrapment Prevention Guidelines
When the pool equipment is located below the pool surface a leak can result in large scale water loss Description or flooding. Zodiac cannot be responsible for such water loss or flooding or damage caused by either The E3 is a variable-speed pump that can be run from occurrence. -
Page 6: Electrical Installation
WARNING Always use properly sized valves. Zodiac When pressure testing the system with water, it is Diverter Valves and Ball Valves typically have very important to make sure that the pump basket lid the best flow capabilities. -
Page 7: Section 4. Operation
If there is no leak, Start-up repeat Steps 2 through 7. CAUTION For technical assistance, call Zodiac Technical Never run the pump without water. Running the Support at 1.800.688.152. pump “dry” for any length of time can cause severe... -
Page 8: Section 5. Service And Maintenance
To avoid risk of property damage, severe personal a qualified technician, visit www.zodiac.com.au injury or death, verify that all power is turned off and click on “Pool Maintenance - Zodiac Product before starting this procedure. Support”. Inspect the pump debris tray basket for debris by looking through the clear pump lid. -
Page 9: Section 6. Troubleshooting And Repair
™ Section 6. Troubleshooting and Repair Zodiac Group Australia Pty Ltd strongly recommends that you call a qualified service technician to perform any repairs on the filter/pump system. To locate a qualified technician, visit www.zodiac.com.au and click on “Pool Maintenance - Zodiac Product Support”. -
Page 10: Fault Codes
Note: Presently, no faults should trigger this indicator. NOTE If you are replacing the motor, Zodiac strongly none EEPROM Checksum failed while recommends that a qualified service technician or load failure... - Page 11 Page 11 Zodiac FloPro E3 3-Speed Variable Pump Installation & Operation Manual ENGLISH ™ Hold the motor shaft with a ¼” hex allen wrench while unscrewing the impeller from the motor shaft with your hand. Turn the impeller counter-clockwise to unscrew it. See Figure 15.
- Page 12 Page 12 ENGLISH Zodiac FloPro E3 3-Speed Variable Pump Installation & Operation Manual ™ NOTE Tighten the screws lightly in a crossing “X” To assist assembly, use only water or soapy water as a lubricant. Any other lubricant will destroy the pattern using a 9/16”...
- Page 13 ® Once all the air has left the filter, close the motor listed in the spares list that has the identical pressure relief valve. HP rating and service factor (Zodiac approved only). NOTE Zodiac recommends that the mechanical seals be replaced at the same time the motor is replaced.
-
Page 14: Section 7. Product Specifications And Technical Data
To order or purchase parts for Zodiac pumps, contact your nearest Zodiac dealer. If the Zodiac dealer cannot ® supply you with what you need, contact Zodiac technical support at 1.800.688.152, or send an e-mail message to apac.aftersales@zodiac.com. Order Part No. -
Page 15: Exploded View
Page 15 Zodiac FloPro E3 3-Speed Variable Pump Installation & Operation Manual ENGLISH ™ Exploded View 2, 5 4, 15 2, 16 1, 17 4, 14 2, 3, 4, 6, 13, 14, 15... - Page 16 219 Woodpark Road Smithfield, NSW AU 2164 1.800.688.552 | www.zodiac.com.au ©2018 Zodiac Pool Systems LLC ZODIAC ® is a registered trademark of Zodiac International, S.A.S.U., used under license. All trademarks referenced herein are the property of their respective owners. H0394700 Rev D...