Table of Contents
Advertisement
Quick Links
RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
INSTALLATION
INSTRUCTIONS
MANUFACTURED HOME
42" Wood Burning Fireplaces
P/N 800,022M REV. A 01/2003
MODELS
BM42HCD-BL
This installation manual will enable you to obtain a safe, efficient and
dependable installation of your fireplace system. Please read and under-
stand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any
circumstances. Any modification or alteration of the fireplace system,
including but not limited to the fireplace, chimney components and
accessories, may void the warranty, listings and approvals of this system
and could result in an unsafe and potentially dangerous installation.
IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS:
INSTALL THIS FIREPLACE IN A SQUARE AND PLUMB CONDITION,
USING SHIMS AS NECESSARY AT SIDES AND/OR BOTTOM.
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
DELUXE 42
FIREPLACES
OTL Report No. 116-F-04-2
1
Advertisement
Table of Contents
Related Manuals for Intertherm DELUXE 42
Summary of Contents for Intertherm DELUXE 42
- Page 1 INSTALLATION INSTRUCTIONS DELUXE 42 MANUFACTURED HOME FIREPLACES 42" Wood Burning Fireplaces P/N 800,022M REV. A 01/2003 MODELS BM42HCD-BL This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and under- stand these instructions before beginning your installation.
-
Page 2: Table Of Contents
3. These fireplaces must be installed with Fire- The manufacturer is not responsible for any TABLE OF CONTENTS Craft Technologies' FTF8 (8" inside diameter) smoking or related problems that may result Chimney System only. These systems are in- from the lack of adequate combustion air. Safety Rules ........ -
Page 3: Precautions
PRECAUTIONS Note: Illustrations shown reflect “typical” WARNING: FAILURE TO USE MANUFAC- installations with nominal dimensions and TURE PROVIDED PARTS, VARIATIONS IN are for design and framing reference only. Note: These fireplace systems are not difficult TECHNIQUES AND CONSTRUCTION MA- Actual installations may vary due to indi- to install. -
Page 4: Assembly Outline
Chimney Enclosure WARNING: DO NOT OBSTRUCT THE OPENINGS AT THE TOP OF THE FIRE- Construct a box-like framed structure to sur- PLACE. NEVER USE BLOWN INSULA- round the fireplace and chimney within the TION TO FILL THE CHIMNEY ENCLOSURE. confines of the manufactured home, not neces- Hearth sarily above the roof line. -
Page 5: Preinstallation Notes
1. Position firebox prior to framing or into CAUTION: DO NOT BLOCK THE HEAT-CIRCU- Top Spacer prepared framing. LATING AIR INLET AND OUTLET PORTS. DOING SO MAY RESULT IN A POTENTIAL FIRE Maintain HAZARD. 2. Install the chimney system. 1" (25 mm) Air Space At Back CAUTION: THE STRUCTURAL INTEGRITY OF... -
Page 6: Fireplace Specifications
FIREPLACE SPECIFICATIONS 12 ¹⁄₂" (318 mm) 8 ³⁄₈" (213 mm) Optional 13 ⁷⁄₁₆" Floor (341 mm) Bracket 41" 1 ¹⁄₂" Metal Safety Strips (1041 mm) 43" (1092 mm) 22 ⁵⁄₁₆" 2" (566 mm) (51 mm) Figure 7 7 ³⁄₁₆" (183 mm) Blocking 45"... -
Page 7: Framing Specifications
FRAMING SPECIFICATIONS Framing Dimensions 46 ¹⁄₄" Back Wall of 1175 mm Chase/Enclosure Including Finising 43 ¹⁄₂" 1105 mm Materials if any 33" 838 mm 17 ¹⁄₂" 445 mm 76 ¹⁄₄" 1937 mm Header 38 ¹⁄₈" 968 mm 21 ⁵⁄₈" 549 mm Rough Framing Face (Unfinished Shown) -
Page 8: Installing The Chimney System
Step 4. Fireplace should be secured to side CAUTION: ALLOW MINIMUM 1" CHIMNEY Room Above framing members using the full length nailing AIR SPACE TO FRAMING MEMBERS THROUGH- tabs at the top and bottom of the fireplace front OUT CHIMNEY INSTALLATION. A MINIMUM 1" face. - Page 9 Outer pipe section installs in just the opposite Install the Model FTF8-S4 stabilizer by fitting WARNING: DO NOT ALLOW INSULATING way; the lanced end goes down and each new inner section down into respective section of MATERIALS TO BE BLOWN INTO THE section goes OVER the outside of the previous proceeding flue pipe and locking outer stabilizer SPACE INSIDE THE THIMBLE AND THE...
-
Page 10: Ten Foot Rule Summary
Step 7. Secure flashing by nailing along the Note: If chimney extends more than 8' above 3. Center outer locking section over outer flue perimeter into roof using 8d nails or equivalent roof surface, guy wires are also recommended. pipe. Push down until locking tabs are firmly fasteners. -
Page 11: Special Offset Instructions
Maximum offset of chimney system is 30°. FTF8 CHIMNEY COMPONENT Room Above Two offsets must not be assembled to form a CALCULATIONS F8FS30-2 60° offset. However, two sets of offset and 1" Min. Firestop Spacer return elbows may be used on a single flue Air Space The minimum installed height of the com- system, provided the total height of the sys-... -
Page 12: Vertical Elevation Chart
FTF8 VERTICAL ELEVATION CHART Height Of Number Of FTF8 Height Of Height Of Number Of FTF8 Height Of Chimney Only Chimney Lengths Chimney Only Chimney Only Chimney Lengths Chimney Only Inches Feet/Inches 12" 18" 36" 48" Inches Feet/Inches 12" 18" 36" 48" 0 11 0.28 6401... -
Page 13: Offset Elevation Chart
FTF8 OFFSET ELEVATION CHART FTF8-ES30 Number of FTF8 Offset Height Offset/Return FTF8-S4 Chimney Sections Offset Height (Inches) (Inches) Elbow Set Stabilizer 12" 18" 36" 48" (mm) (mm) 15 ³⁄₄ 24 ¹⁄₂ 29 ³⁄₄ 14 ¹⁄₄ 33 ¹⁄₂ 17 ¹⁄₄ 38 ¹⁄₂ 20 ¹⁄₄... -
Page 14: Installing Offsets
Offset Elbow Assembly Note: These fireplace models are not supplied with an optional wall switch (FWSK) for fan operation. BFK36 blower kits may be operated Offset elbows install the same as chimney with their integral blower (On/Off) switch. sections. First, snap the inner section INTO the preceding inner section of flue. -
Page 15: Combustion Air Kits
Always check local building codes. Installa- CAUTION: WHEN USING THE DECORATIVE Combustion Air Actuator tion of the BFK36 Blower Kit must comply GAS APPLIANCE, THE FIREPLACE DAMPER with local regulations as well as the National MUST BE SET IN THE FULLY OPEN POSITION. Electric Code. -
Page 16: Glass Doors
Glass Doors Combustible mantels and trim may be in- stalled 12" above the fireplace opening as per NFPA 211, Section 7-2.3.3. and Figure 44 . If Glass doors have been installed on these a mantel is of a noncombustible material, it is fireplaces as standard equipment. - Page 17 = 0.09 x ³⁄₄" = .068 “R value” = 1 = r x thickness of material used “R” = r x T Methods of Determining Hearth Extension = 0.20 x ¹⁄₂" = .10 “R” = r x T and Wall Shield Equivalents Alternative Hearth Extension The sum of all “R values”...
-
Page 18: Finish Requirements
FINISH TO YOUR TASTE INSTALLATION COMPONENTS There are a wide variety of “finished looks” for The following items are available for use in the these fireplaces, from formal wall decor with installation of this appliance. elaborate mantels to rustic wood paneling or warm brick facings. - Page 19 INSTALLATION COMPONENTS Stabilizer 63L25 FTF8-S4 Forced Air Blower Kit 36L32 BFK36 Firestop Spacer (30°) 63L30 F8FS30 Firestop Spacer (Flat) 63L29 F8FS Cold Climate Kits 63L65 FTF8-CCK3-LD Termination 90L81 FBTM NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
- Page 20 The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © 2002 by LHP 1110 West Taft Avenue P/N 800,022M REV.