Related Manuals for Colorlight Q7H
Summary of Contents for Colorlight Q7H
- Page 1 User Manual Q7H HD Sender User Manual www.colorlight-led.com Version: V1.0 2015/11/26...
-
Page 2: Table Of Contents
User Manual Contents I. Product introduction ..............3 II. Hardware ..................4 III. Hardware Connection Diagram ............. 6 IV. Operating Environment ..............7 V. Parameter Configuration ............. 10 www.colorlight-led.com Version: V1.0 2015/11/26... -
Page 3: Product Introduction
User Manual Product introduction Q7H HD sender is specially designed for the HD display. It supports the widest of 2560 pixels, highest of 1600 pixels, and has 4 gigabit Ethernet outputs can help to support supper large screen. It supports 12bit color input, dual USB2.0 high-speed communication interfaces are specially for configuration and cascading. -
Page 4: Hardware
Brightness adjustment Hold down two keys at once (16 levels)； Setting button to change the mode between brightness and testing Full screen testing mode ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ www.colorlight-led.com Version: V1.0 2015/11/26... - Page 5 For input cascade signal from the last Cascade input Audio input Support DVI input DVI signal input HDMI input HDMI signal input USB 2.0 For Q7H and PC communication Output port RJ45,4 outputs, connect to receiver cards www.colorlight-led.com Version: V1.0 2015/11/26...
-
Page 6: Hardware Connection Diagram
Q7H has HDMI and DVI two video input interface, choose any one of them to input video according actual. If you need to switch video input mode between HDMI and DVI signal, can use HDMI and DVI cable to connect the computer and Q7H at the same time. -
Page 7: Operating Environment
1、Check ‘USB Drive For Sending Card’ when install the LEDVISION, as you can see in following picture. Fig.4-1 2、Open the CD-ROM, find the file name of "USB driver for sending card" and double click it to install. www.colorlight-led.com Version: V1.0 2015/11/26... - Page 8 The second way: Right-click and select “screen resolution” to enter the page of “modify the display appearance”; if your graphics card is not NVIDIA and cannot find the setting interface please refer to the description of the graphics card. www.colorlight-led.com Version: V1.0 2015/11/26...
- Page 9 User Manual Fig.4-4 Fig.4-5 www.colorlight-led.com Version: V1.0 2015/11/26...
-
Page 10: Parameter Configuration
Management window, the Sender Mode select “By Sender Card”, Click “Detect Sender Cards”, the sender cards information will show in the interface, (as shown in Fig.5-2 ) Please check the hardware connection if cannot detect sende www.colorlight-led.com Version: V1.0 2015/11/26... - Page 11 Select network port and click “Detect Receiver Cards”, the software will automatic acquisition the Receiver (Receiving card) quantity for each network port of the sending card. Please check cable if the numbers of receiving card are inconsistent with actual. (As shown in Fig.6-3) www.colorlight-led.com Version: V1.0 2015/11/26...
- Page 12 User Manual Fig.5-3 5.2 LED Screen Setting Click “Led Screen Setting” by using password: 168 to enter the Led Play Screen Setting interface, click “Advance Settings” (As shown in Fig.6-4) 5.2.1 Sender Card Setting www.colorlight-led.com Version: V1.0 2015/11/26...
- Page 13 It contains the following parameters setting in Advanced Settings. 3D Setting: Q7H is no need to set this item because only for 3D Sender feature setting. Write Logo: Can be written to the customer specified image such as logo, and display before the video signal is not input.
- Page 14 The second step: Click “Send” to send the parameter to receiver cards, at this moment, all cabinets should display normally (the picture between cabinets is not continuous but also as normal), then click “Save To Receiver”. Please contact display manufacturer of engineering and technical personnel if display abnormally. www.colorlight-led.com Version: V1.0 2015/11/26...
- Page 15 Configuration Receiver (Receiving Card) connection pattern for each port individually if more than one port are used. There are two methods to set up. Note: Set up connection Receiver (Receiving Card) must be based on fact. www.colorlight-led.com Version: V1.0 2015/11/26...
- Page 16 (Viewing from the front of led display). As shown in 5-8. Fig.5-8 Connection Pattern Select the connection pattern based on fact, and then select this port load Receiver (Receiving card) in the display mapping area. (As shown in 5-9) www.colorlight-led.com Version: V1.0 2015/11/26...
- Page 17 After set up the Receiver (Receiving card) parameters and connection pattern for each network port of the sending card, LED display will available when click “Send”. Please determine that no mistake then click “Send to Receiver” to save the parameter www.colorlight-led.com Version: V1.0 2015/11/26...
- Page 18 User Manual in Receiver (Receiving card). Fig.5-11 www.colorlight-led.com Version: V1.0 2015/11/26...
Need help?
Do you have a question about the Q7H and is the answer not in the manual?
Questions and answers