Subscribe to Our Youtube Channel
Related Manuals for Geemarc HP5990A
Summary of Contents for Geemarc HP5990A
- Page 1 Contents 900MHz Wireless Headphone HP5990A, HP5990, HP5990J, HP5990AJ English !!!Please ensure you read the user manual thoroughly before use!!!
-
Page 2: Table Of Contents
!!!Please refer to our website: www.geemarc.com for an up to date user guide, as there may be important updates and changes you need to be aware of!!! INTRODUCTION ............3 SAFETY & CARE ADVICE ....... 4 PACK COMPONENTS ..........5 FUNCTION IDENTIFICATION ........ - Page 3 INTRODUCTION Contents TROUBLESHOOTING ........18 ● No Sound ..............18 ● Distortion ..............18 Cleaning & Maintenance ........... 19 Spare/replacement parts ........... 19 Customer support ............19 GUARANTEE .............. 20 CE DECLARATION ............. 20 BATTERY WARNINGS ........21 DISPOSAL INFORMATION ........21 INTRODUCTION...
- Page 4 The Geemarc Wireless Audio Listener is an audio amplification system specifically designed for people with hearing difficulties. The Geemarc Audio Listener can be used with all kinds of audio systems for interference-free listening enjoyment – TV set, Smartphone, DVD player, CD player, Hi-Fi system, iPod or other.
-
Page 5: Safety & Care Advice
Electrical connection: The unit is designed to operate from a 100-240VAC - 50/60Hz supply. (Classified as 'hazardous voltage' according to EN 60650 standard). Caution: Batteries should only be replaced by Geemarc or authorised Vendor. Please refer to the chapter: <Spare / replacement parts> for more information. -
Page 6: Pack Components
PACK COMPONENTS PACK COMPONENTS (1) Headset Receiver/TV Receiver(with Belt Clip) (2) Charging Cradle and Transmitter (3) Power Supply (4) Optical Cable (5) Ear Phone... -
Page 7: Function Identification
FUNCTION IDENTIFICATION FUNCTION IDENTIFICATION Function Identification: Headset Receiver FRONT REAR (1) Earbuds (2) Volume Control (3) Power/Signal LED Indicator... -
Page 8: Function Identification: Charging Cradle
FUNCTION IDENTIFICATION (4) Mute Button for Verbal Communications (5) Microphone (6) Auto Tune Button for Frequency Channel (7) Sound Balance Control (8) Power On/Off Switch (9) Battery Contact Function Identification: Charging Cradle... -
Page 9: Installation
FRONT REAR (1) Charging Pins (2) Tone Adjustment (3) LED Indicator: Battery Charge (Red = charging, Green = fully charged) (4) LED Indicator (Green): Audio Signal (5) LED Indicator (Green): Power (6) LED Indicator (Yellow): Treble enhanced (7) LED Indicator (Blue): Bass enhanced (8) Audio In (9) Frequency Channel Selector (CH1 or CH2) (10) Optical In Socket... -
Page 10: Transmitter
INSTALLATION INSTALLATION INSTALLATION Transmitter (1) Connect the Power Supply to the DC IN Socket located on the Charge Cradle rear panel. (2) Connect the Power Supply to an electricity socket (100- 240V ~ 50/60Hz). The green Power Indicator LED will glow immediately. (3) Connect one end of the Optical Cable to the rear panel of the Charge Cradle. -
Page 11: Headset
OPERATION components) that connects to the Audio In of the Transmitter. • 3.5mm to 3.5mm Audio Cable • 3.5mm to 6.3mm Adapter Plug • RCA Adapter Cable • SCART Adapter (7) On the rear panel of the Charging Cradle, switch the Power ON/OFF Switch to ON. -
Page 12: Initial Operation
Initial Operation 1. Make sure the CL7350 is plugged into the electricity. 2. Switch ON the CL7350 – on the rear of the Charging Cradle (see figure (1) at right). 3. Place the Headset in the Charging Cradle for at least three hours to allow it to fully charge. -
Page 13: Improving Sound By Switching Channels
OPERATION OPERATION 1. Switch on the Audio Source (TV set or audio device) that the Transmitter is connected to. The Signal LED Indicator will glow continuously (see figure (4) at right). 2. On the Headset Receiver, switch the ON the On/Off Switch (see figure (5) at right). -
Page 14: Controlling The Tone (Bass & Treble)
OPERATION The CL7350 can transmit on either of two built-in frequency channels. You can select the channel that will produce better audio quality. 1. If the audio sound is distorted or unclear, press the Auto Tune Button on the Headset Receiver (see figure (7) at right), to match the frequency of Channel 1 or Channel 2... -
Page 15: Adjusting The Sound Balance (Left-Right)
OPERATION You can adjust the tone of the audio you are listening to and enhance your listening pleasure by amplifying either the Treble or the Bass in the Headset Receiver. Press the Tone Clarity Button to switch cyclically between : 1. -
Page 16: Using The Mute Button And Microphone For Conversation
OPERATION You can adjust the sound to suit your hearing in each ear. With the Headset on, rotate the Sound Balance button (see figure (10) at right) to adjust the sound – you will notice that the sound seems to “drift” from one side to the other. - Page 17 OPERATION 1. The signal LED Indicator on the Headset Receiver will blink slowly when the battery level is low. At this stage there are about 20 minutes of operating time before the Headset will switch off. Recharge the battery. 2. Switch OFF the On/Off Switch on the Headset (see figure (12) at right).
-
Page 18: Technical Specifications
TECHNICAL SPECIFICATIONS acceptable service life for the rechargeable battery. Always ensure that the Headphone Receiver is switched to OFF position while the battery are charging. Excessive sound pressure from earphones and headphones can cause hearing loss. IMPORTANT: This unit should be operated with built-in rechargeable battery only. -
Page 19: Troubleshooting
TROUBLESHOOTING Battery operating Time : Up to 6 Hours : Up to 60 meters (CL7350_VDE) Range : Up to 30 meters (CL7350_US) Frequency response : 30 Hz – 10K Hz Signal-to-noise ratio : >65 dB Distortion : <2% Headset weight : 58 grams : Charging Cradle: 8V, 400mA Operating voltage... -
Page 20: No Sound
Cleaning & Maintenance . Spare/replacement parts . Customer support No Sound ● Ensure the power supply is properly plugged into the electricity socket and that its cable is properly connected to the DC IN connector on the Charge Cradle. ● Ensure that the Headset Power ON/OFF switch is switched ON. ●... -
Page 21: Spare/Replacement Parts
01707 387602 1. Additional Headsets 2. Ear pads To replace the Headset battery, please contact Customer Support. Customer support For product support and help, visit our website at www.geemarc.com For our Customer Helpline Telephone: 01707 387602 Fax: 01707 832529 GUARANTEE... -
Page 22: Battery Warnings
The product must not be tampered with or taken apart by anyone who is not an authorised Geemarc representative. The Geemarc guarantee in no way limits your legal rights. Important: YOUR RECEIPT IS PART OF YOUR GUARANTEE AND MUST BE RETAINED AND PRODUCED IN THE EVENT OF A WARRANTY CLAIM. - Page 23 DO NOT short-circuit the Battery Contact terminals. Exhausted batteries are to be replaced only by a certified Geemarc service technician. Caution: Risk of explosion if battery is replaced incorrectly or if the wrong type of battery is used. Dispose of used batteries according to the instructions.
- Page 24 This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two co nditions: (1) this device may not cause interference, and (2) t his device must accept any interference, including interferenc e that may cause undesired operation of the device. Le present appareil est conforme aux CNR d’Industrie Canad a applicables aux appareils radio exempts de licence.
- Page 25 For product support and help visit our website at www.geemarc.com telephone 01707 387602 or fax 01707 832529 UGCL7350_En_v1.1...
Need help?
Do you have a question about the HP5990A and is the answer not in the manual?
Questions and answers