Do you have a question about the 90500 and is the answer not in the manual?
Questions and answers
John
July 17, 2025
Hello. I have wired in my pump and replumbed it. I turned back on the power and the led display just lights up with the time. When I press a button it just beeps and nothing is happening after that. It won’t even start. I have a 30 amp breaker for the pump. Please help my water is green!!! Thanks!
Page 1
Inground ® VS Pumps Item #s 90500 90550 INSTALLATION, OPERATION & PARTS To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely. SAVE THIS INSTRUCTION MANUAL Use of aftermarket replacement parts voids warranty.
Page 2
CHAPTER 1 7. MODE 2: Run programmed 24 hours clean cycle. 8. Enter: Save and exit the menu. SAVE THIS INSTRUCTION MANUAL 9. ARROW BUTTONS: UP ARROW: Move up one level in the menu or to Brief Introduction increase a digit when changing a setting. This variable speed pump is designed to operate your DOWN ARROW: Move one level down in the menu swimming pool filtration system as well as your spa,...
Page 3
CHAPTER 4 Pump Run Under Pre-Programmed Conditions Pump has three quick start button ECO / CLEAN / STOP AND RUN THE PUMP BOOST, as below image. The default speed is 1500, 2400, 3250RPM respectively. Start the Pump 1. Be sure the pump is power on. 1.
Page 4
CHAPTER 6 How to Set and Change Specifications of Mode 1 / Mode 2 HOW TO OPERATE THE PUMP 1. Make sure STOP button is pressed before set up, Programmed Schedules and pump is not working. Press MENU, LED screen Totally three pre-programmed schedules: Regular will display the current time (time will not count Mode ( including ECO;...
Page 5
Control Panel Menu Structure 00:00 - 11:59 SET TIME 12:00 - 23:59 TIME SETUP Default 06:00 Default 06:00 Default 3 hours Default 09:00 Default 5 hours MODEL 1 Default 18:00 Default 3 hours Default 21:00 Default 5 hours MENU Default 06:00 Default 3 hours Default 09:00 Default 9 hours...
Page 6
Inground Pump Item #’s 15900 & 15901 PART DESCRIPTION NUMBER REQ’D 648910606080 Handle Screws 48915102089 Cover 65432053080 Gasket 48910402001 Basket 648915105080 Pump Housing 1.5” 648915104080 Pump Housing 2” 65432040080 O-Ring 647258001080 Diffuser 89106201 Impeller for 1.5 HP Pump 72580071 Impeller for 3 HP Pump 65028026000 Seal Assembly 65431121080...
Page 7
CHAPTER 7 Alert Code Details PERFORMANCE CURVE Code Error Blocked/Short Circuit/Overheat Voltage input exceeds limit High input voltage Low input voltage Exceeds maximum speed Speed is 0 Motor phase loss Abnormal start-up System configuration error Stall at start-up 1024 System operation error, contact Harris 4096 Hardware test error, contact Harris CHAPTER 8...
Page 8
1 Year Limited Doheny's Pool Pump Warranty Please read installation instructions before installing pool pump This pump was inspected before shipment from our warehouse. To original purchasers of this pump, Doheny Enterprises, Inc., 10411 80th Ave, Pleasant Prairie, WI, warrants its products free from defects in materials and workmanship for a period of ONE (1) year from the date of purchase.
Need help?
Do you have a question about the 90500 and is the answer not in the manual?
Questions and answers
Hello. I have wired in my pump and replumbed it. I turned back on the power and the led display just lights up with the time. When I press a button it just beeps and nothing is happening after that. It won’t even start. I have a 30 amp breaker for the pump. Please help my water is green!!! Thanks!