Advertisement
Initial Setup
The following sections provide instructions for the initial setup of the time switch.
Setting The Output Configuration
The time switch output configuration enables users to control multiple loads simultaneously (SIM), independently (IND), or with a
2-second pulse (PUL). Output circuits are configured in pairs.
In PUL mode, an ON event or manual override, causes circuit #1 to turn ON for two seconds, then OFF. An OFF event, or manual
override, causes circuit #2 to turn ON for two seconds, then OFF.
NOTE: The output configuration setup can only be accessed at initial startup of the unit or after a "Clearing Time Switch Memory"
operation. Follow this procedure to set the output configuration.
1.
Activate power to the time switch. The display shows IND, the ARROW icon above the ENTER/NEXT button and the LOAD
icons for circuit #1 and circuit #2 turn on.
NOTE: If the display does not show IND the output configuration is already set and a "Clearing Time Switch Memory" operation
must be performed.
2.
Press + or - to scroll to the desired output configuration.
3.
Press ENTER/NEXT to save the setting.
4.
The output configuration is now completed.
Programming Overview
The steps to program the time switch include setting the current date, time, fixed events, DST, and holiday events, setting the time
switch's operation to AUTO mode, ENERGY SAVER mode or MANUAL mode (only MANUAL mode will appear if there are no
scheduled events) and read or write an event schedule from a USB memory stick.
NOTE: If the time switch is left inactive for five minutes in a programming mode, it will return to the AUTO mode screen (AUTO icon
turned on). If no scheduled events are programmed, the time switch will return to MANUAL mode. If the date has not yet been
entered, the time switch will go to the Enter Date Mode.
Setting Date
Follow this procedure below to set the date and time in the time switch.
NOTE: If necessary, hold + or - to scroll through the digits rapidly.
Press MODE to scroll through the mode selections until SET and DATE icons appear at the top of the display. The month
1.
flashes.
2.
Press + or - to select the current month and then press ENTER/NEXT. The day of the month flashes.
3.
Press + or - to select the current day of the month, and then press ENTER/NEXT. The year flashes.
4.
Press + or - to enter the current year, and press ENTER/NEXT. The month will flash again.
5.
Press MODE to move to the next mode selection.
Setting Time
Follow the procedure below to set the time in the time switch.
NOTE: If necessary, hold + or - to scroll through the digits rapidly.
1.
Press MODE to advance to the Set Clock mode selection if this selection is not already active. The SET and TIME icons appear
on the display and a flashing 12:00 AM appears (if clock has not been set).
2.
Press + or - to select the current time. NOTE: Seconds can be set to 00 by pressing ENTER/NEXT.
3.
Press MODE to save the time and move to the Enable Daylight Saving Time mode selection.
NOTE: If the time switch programming data is to be read from a USB memory stick, refer to the "Read Time Switch Program
Data..." section in these instructions.
Enable/Disable Daylight Saving Time and Setting Daylight Saving Time Rule
Configure the time switch to automatically adjust for Daylight Saving Time (DST). If DST does not apply to your region, disable the
option as directed in this procedure. Follow this procedure to enable/disable the Daylight Saving Time feature, and if applicable, set
the DST rule.
1.
Press MODE to advance to the Set DST mode selection if this selection is not already active. The SET and DST icons appear on
the display.
2.
Press + to display ON (enable DST) or press – to display OFF (disable DST) and then press ENTER/NEXT to save.
If DST is
Enabled
Disabled
3.
Press + or - to scroll to the desired DST rules for your area.
NOTE: The DST rules are US2007 (US rules), MX1986 (Mexico rules), and CUSTOM (user-defined start/end dates).
Then
Go to step 3.
Press MODE to save and exit. The procedure is complete.
Advertisement
