Advertisement
Quick Links
100, 150 & 200 LITRE
COMPRESSORS
■ STOCK Nos.77709
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE
This manual has been compiled by Draper Tools and is an integrated part of the product with which it is enclosed
and should be kept with it for future references.
This manual describes the purpose for which the product has been designed and contains all the necessary
information to ensure its correct and safe use. We recommend that this manual is read before any operation or,
before performing any kind of adjustment to the product and prior to any maintenance tasks. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together with
longer life of the tool itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
77897
77711
• INSTRUCTIONS •
SAFE AND EFFECTIVE USE OF THIS TOOL.
GENERAL INFORMATION
■ PART Nos.DA100/300B
DA150/300B
DA200/300B
01/2005
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Draper DA150/300B
Summary of Contents for Draper DA150/300B
- Page 1 01/2005 GENERAL INFORMATION This manual has been compiled by Draper Tools and is an integrated part of the product with which it is enclosed and should be kept with it for future references. This manual describes the purpose for which the product has been designed and contains all the necessary information to ensure its correct and safe use.
- Page 2 Operation and Use 6 - 8 Maintenance 8 - 10 Trouble Shooting DECLARATION OF CONFORMITY Draper Tools Ltd. Hursley Road, Chandler’s Ford, Eastleigh, Hampshire. SO53 1YF. England. Declare under our sole responsibility that the product: Stock No:- 77709, 77897, 77711. Part No:- DA100/300B, DA150/300B, DA200/300B.
- Page 3 This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the 12 month period.
- Page 4 POWER SUPPLY CONNECTING YOUR MACHINE TO THE POWER SUPPLY The machine should be connected to a 16amp power supply either using the appropriate blue 16amp plug or directly into the fused mains supply. Both of these operations should be carried out by a qualified electrician. *WARNING A plug with bare flexible wires exposed is hazardous if engaged in a live power socket outlet.
- Page 5 IMPORTANT: Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you.
- Page 6 GETTING TO K NOW YOUR COMPRESSOR (16) (11) (12) (10) (13) (15) (14) DA150/300B Shown (1) Air Receiver Tank (7) Drive Belt (13) Tank Pressure Gauge (2) Sump Bung (8) Motor (14) Tank Bung (3) Pump Unit (9) Overload Protection Switch...
- Page 7 OPERATION AND USE POSITIONING: Fig.1. Do not stand the compressor on any surface with a 15° or greater tilt as this will lead to possible running problems. Allow a minimum gap of 50cm around the compressor to aid connection and airflow. In addition to pneumatic air tools, your compressor may be connected to several accessories suitable for blowing, washing...
- Page 8 OPERATION AND USE ADJUSTING THE PRESSURE SWITCH Fig.5. (Fig.5): Note: This is the only operation where it is acceptable to switch the compressor off without using the pressure switch. To decrease the pressure switch, run the compressor up to the desired capacity for the pressure switch to be set.
- Page 9 Draper Stock No.51857 - Air Filter, Regulator & Lubricator. Draper Stock No.51858 - Air Filter & Regulator. To ensure an optimum air supply, please refer and carry out the following procedures...
- Page 10 MAINTENANCE In order to keep your compressor in good Fig.8. working conditions, we recommend you to perform periodical servicing operations. Before performing any maintenance operation, switch off the compressor and ensure all air in the tank is released. OPERATIONS TO BE CARRIED OUT AFTER THE FIRST 50 WORKING HOURS: Check that all screws are properly tight, paying special care to the head and crank...
- Page 11 MAINTENANCE It is advisable to clean all the finned parts of Fig.11. your compressor, so as to keep the cooling system efficient and to ensure a long work life to your machine. Check belt tension. Hang a weight of about 3kg at the midpoint of the belt.
- Page 12 TROUBLE SHOOTING USE ONLY ORIGINAL SPARE PARTS, AVAILABLE AT ALL AUTHORIZED SERVICE CENTRES. FAULT POSSIBLE CAUSE REMEDY Pressure drop in tank Air leaks at connections Allow the compressor to reach max. pressure allowed. Switch it of and brush a soapy water solution onto all air connections.
- Page 13 NOTES - 12 -...
- Page 14 NOTES...
- Page 15 NOTES...
- Page 16 ©Published by Draper Tools Ltd. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Need help?
Do you have a question about the DA150/300B and is the answer not in the manual?
Questions and answers