Related Manuals for NavigateWorx NR300
Summary of Contents for NavigateWorx NR300
- Page 1 Industrial Cellular VPN Router NR300 User Manual Guangzhou Navigateworx Technologies Co, Ltd www.navigateworx.com...
- Page 2 Information provided in this manual is intended to be accurate and reliable. However, Navigateworx Technologies assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use.
- Page 3 Operation in the presence of other electronic equipment may cause interference if equipment is • incorrectly protected. Follow recommendations for installation from equipment manufacturers. Declaration of Conformity NR300 Series products are in conformity with the essential requirements and other relevant provisions of the CE and RoHS. Page 2 / 70...
-
Page 4: Table Of Contents
Industrial Cellular VPN Router NR500 Series User Manual Table of Contents Chapter 1. Product Overview ..........................5 Overview ..............................5 Features and Benefits .......................... 5 General Specifications ........................6 Mechanical Specifications ........................ 8 Package Checklist ..........................9 Order Information ..........................11 Chapter 2. - Page 5 Industrial Cellular VPN Router NR500 Series User Manual 4.7.1 OpenVPN .............................. 49 4.7.2 IPSec ............................... 54 4.7.3 GRE ................................57 Maintenance ............................58 4.8.1 Upgrade ..............................58 4.8.2 Software ..............................59 4.8.3 System ..............................60 4.8.4 Configuration ............................64 4.8.5 Debug Tools ............................
-
Page 6: Chapter 1. Product Overview
This router enables wireless data connectivity over public and private LTE cellular networks at 4G speeds. NR300 series router has dual SIM backup, 1 LAN ports. RS232 and RS485 interfaces are provided to support Serial to IP communication. -
Page 7: General Specifications
Industrial Cellular VPN Router NR500 Series User Manual 1.3 General Specifications Cellular Interface Standards: FDD-LTE, WCDMA/UMTS/HSPA/HSPA+/EDGE/GPRS, • 2× SMA female antenna connector • 2 x SIM (3.0V & 1.8V) • Ethernet Interface Standard: IEEE 802.3, IEEE 802.3u • Number of Ports: •... - Page 8 Industrial Cellular VPN Router NR500 Series User Manual Power consumption: • Idle: 50 mA@12V Data link: 200 mA (peak) @12V Physical Specification Ingress Protection: IP30 • Housing & Weight: Metal, 200g • Dimension: 82.8mm x 93.3mm x 28.8mm (excluding antenna) •...
-
Page 9: Mechanical Specifications
Industrial Cellular VPN Router NR500 Series User Manual 1.4 Mechanical Specifications Dimension: 82.8mm x 93.3mm x 28.8mm FRONT SIDE TOP SIDE BOTTOM SIDE Antenna LEDs SIM Slot Terminal Ethernet 93.3 mm block 28.8 mm 28.8 mm 82.8 mm 82.8 mm 82.8 mm Page 8 / 70... -
Page 10: Package Checklist
Industrial Cellular VPN Router NR500 Series User Manual 1.5 Package Checklist NR300 series Router includes the parts shown in below, please verify your components. NOTE: if any of the below items is missing or damaged, please contact your sales representative. Included equipment 1 x Navigateworx NR300 series Industrial Cellular VPN router •... - Page 11 Industrial Cellular VPN Router NR500 Series User Manual 1 x Quick Start Guide • Optional Accessories (sold separately) 3G/4G cellular antenna • Stubby antenna Magnet antenna 35mm Din-rail mounting kit • AC/DC power adapter (12VDC, 1.5A; EU/US/UK/AU plug optional) • Page 10 / 70...
-
Page 12: Order Information
Industrial Cellular VPN Router NR500 Series User Manual 1.6 Order Information Model Part Number Description 4G LTE, Dual SIMs, 1 x Eth, 1 x RS232 (3 PIN), 1 x NR300-4G A301430 RS485, 9 - 36VDC. Page 11 / 70... -
Page 13: Chapter 2. Installation
Industrial Cellular VPN Router NR500 Series User Manual Chapter 2. Installation 2.1 Product Overview Front Panel • ① Cellular Antenna ② RST Button ③ LED Indicator ④ SIM Slot ⑤ Power Input/RS232/RS485 ⑥ Ethernet Port Page 12 / 70... -
Page 14: Led Indicators
Industrial Cellular VPN Router NR500 Series User Manual 2.2 LED Indicators Name Color Status Description Operating normally Slow Blinking (500ms duration) Fast Blinking System initialing Green Power is off Register to Highest priority network service (depend on Radio, e.g. Radio support LTE as Highest priority network). -
Page 15: Ethernet Port Indicator
Industrial Cellular VPN Router NR500 Series User Manual 2.3 Ethernet Port Indicator Name Status Description Connection is established Blinking Data is being transmitted Link indicator Connection is not established 2.4 PIN Definition of Terminal block Power Input & Serial Port •... -
Page 16: Reset Button
Industrial Cellular VPN Router NR500 Series User Manual 2.5 Reset Button Function Action Press the RST button within 3s under operation status Reboot Press the RST button between 3s to 10s, all LEDs blink few times then Factory Reset reboot the router manually. Press the RST button more than 10s, router will run normally without Run Normally reboot or factory reset. -
Page 17: Din-Rail Mounting
Industrial Cellular VPN Router NR500 Series User Manual NOTE: NR300 router supports dual antennas with MAIN and AUX connectors. MAIN connector is for data receiving and transmission. AUX connector is for enhancing signal strength, which cannot be used separately. 2.8 DIN-rail Mounting Use 4 pcs of M3x6 flat head phillips screws to fix the DIN-rail to the router. -
Page 18: Power Supply Installation
Industrial Cellular VPN Router NR500 Series User Manual 2.9 Power Supply Installation Remove the pluggable connector from the unit, then loosen the screws for the locking flanges as needed. Connect the wires of the power supply to the terminals. 2.10 Power On The Router Connect one end of the Ethernet cable to the LAN port on the unit and the other end to a LAN port on a PC. -
Page 19: Chapter 3. Access To Web Page
Chapter 3. Access to Web page 3.1 PC Configuration NR300 router contains a DHCP server which will automatically assign an IP address to your PC, however in some cases the user may need to change the network settings on their PC to accept the IP address from the N300. -
Page 20: Factory Default Settings
NOTE：Default gateway and DNS server is not necessary if PC not routing all traffic go through NR500 router. 3.2 Factory Default Settings NR300 router supports Web-based configuration interface for management. If this is the first time for you to configure the router, please refer to below default settings. Username: admin Password: admin LAN IP Address: 192.168.5.1... -
Page 21: Login To Web Page
Industrial Cellular VPN Router NR500 Series User Manual 3.3 Login to Web Page 1. Start a Web browser on your PC (Chrome and IE are recommended), enter 192.168.5.1 into the address bar of the web browser. 2. Then use the default username and password(admin/admin), to log in to the router. Page 20 / 70... -
Page 22: Chapter 4. Web Configuration
Industrial Cellular VPN Router NR500 Series User Manual Chapter 4. Web Configuration 4.1 Web Interface The N300 router Web interface is divided into two sections. In the left pane is the main navigation menu. On the right is the content area for each page. NOTE: The navigation menu may contain fewer sections than shown here depending on which options are installed in your unit. - Page 23 Industrial Cellular VPN Router NR500 Series User Manual Reboot: reset the router within power disconnect. • Logout: logout to web authorization page. • Save: save the configuration on current page. • Apply: apply the changes on current page immediately. • Close: exit without changing the configuration on current page.
-
Page 24: Overview
Industrial Cellular VPN Router NR500 Series User Manual 4.2 Overview 4.2.1 Status You can view the system information of the router on this page. System Information Device Module • Displays the model name of router System Uptime • Displays the duration the system has been up in hours, minutes and seconds. System Time •... - Page 25 Industrial Cellular VPN Router NR500 Series User Manual Active Link Information Link Type • Current interface for internet access. IP Address • Displays the IP address assigned to this interface. Netmask • Displays the subnet mask of this interface. Gateway •...
-
Page 26: Syslog
Industrial Cellular VPN Router NR500 Series User Manual 4.2.2 Syslog Syslog Information Download Diagnosis • Download the Diagnosis file for analysis. Download Syslog • Download the complete syslog since last reboot. Clear • Clear the current page syslog printing. Refresh •... -
Page 27: Link Management
Industrial Cellular VPN Router NR500 Series User Manual Link Management This section shows you the setup of link management. 4.3.1 Connection Manager Connection Manager->Status Type • Displays the connection interface Status • Displays the connection status of this interface. IP Address •... - Page 28 Industrial Cellular VPN Router NR500 Series User Manual Connection Manager->Connection Priority • Displays the priority list of default routing selection. Enable • Displays the connection enable status. Connection Type • Displays the name of this interface. Description • Displays the description of this connection. Connection Settings Priority •...
- Page 29 Industrial Cellular VPN Router NR500 Series User Manual Interval • The duration of each ICMP detection in seconds. Retry Interval • The interval in seconds between each ping if no packets have been received. Timeout • Enter timeout for received ping reply to determine the ICMP detection failure. Retry Times •...
-
Page 30: Cellular
Industrial Cellular VPN Router NR500 Series User Manual 4.3.2 Cellular NR300 Router main function is connecting to Internet by cellular modem. Cellular->Status Modem • Displays the module of the modem used by this WWAN interface. Registration • Displays the registration status of SIM card. - Page 31 SIM card, reboot would not erase this data. RX Bytes • Displays the total bytes received since the time the unit was connected. NR300 router would record this data with same SIM card, reboot would not erase this data. Modem Firmware •...
- Page 32 Industrial Cellular VPN Router NR500 Series User Manual SIM Card Settings SIM Card • Displays the current SIM card settings. Auto APN • Check this box enable auto checking the Access Point Name provided by the carrier. Dial Number • Enter the dial number of the carrier.
-
Page 33: Ethernet
Industrial Cellular VPN Router NR500 Series User Manual 4.3.3 Ethernet The same instructions apply to settings for all Ethernet interfaces. Ethernet->Status Ethernet Port Information • Displays the port physical connected states. Interface Information • Displays the name and MAC address of Ethernet interface. DHCP Lease Table •... - Page 34 Industrial Cellular VPN Router NR500 Series User Manual Ethernet->Port Settings Port • Indicate the current configurate port. Interface • Select belong subnet for current configurate port. Ethernet->LAN Interface • Displays current name of LAN subnet. IP Address • Displays LAN IP address of this subnet. Netmask •...
- Page 35 Industrial Cellular VPN Router NR500 Series User Manual Ethernet->LAN Interface • Select the configurate LAN port of this subnet. IP Address • Enter LAN IP address for this interface. Netmask • Enter subnet mask for this subnet. • Maximum Transmission Unit, maximum packet size allowed to be transmitted. Should be left as default value of 1500 in most cases.
- Page 36 Industrial Cellular VPN Router NR500 Series User Manual Select the DHCP working mode from “Server” or “Relay”. Relay Server • Enter the IP address of DHCP relay server. IP Pool Start • External LAN devices connected to this unit will be assigned IP address in this range when DHCP is enabled.
- Page 37 Industrial Cellular VPN Router NR500 Series User Manual Ethernet->VLAN->VLAN Trunk Settings Interface • Select the LAN port for VLAN trunk. • Specify the VLAN ID for VLAN trunk. IP Address • Enter IP address for this VLAN trunk. Netmask • Enter subnet mask for this VLAN trunk.
-
Page 38: Industrial Interface
Industrial Cellular VPN Router NR500 Series User Manual 4.4 Industrial Interface The Industrial page contains tabs for making configuration settings for Serial RS232 and RS485. Select Serial from the main navigation menu to navigate to this page. 4.4.1 Serial You could review the status of serial connection. Serial->Status Enable •... - Page 39 Industrial Cellular VPN Router NR500 Series User Manual Serial->Connection Enable • Displays status of current serial function. Port • Displays the serial type of COM port. Baud Rate • Displays the serial port baud rate. Data Bits • Displays the serial port Data Bits. Stop Bits •...
- Page 40 Industrial Cellular VPN Router NR500 Series User Manual Serial->Connection Settings Baud Rate • Select the serial port baud rate. Supported values are 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, or 115200. Data Bits • Select the values from 7 or 8. Stop Bits •...
- Page 41 Industrial Cellular VPN Router NR500 Series User Manual Below window displays different settings when you select UDP on Protocol. Serial->Connection Settings Local IP Address • Enter the IP Address of the local endpoint. Local Port • The port number assigned to the serial IP port on which communications will take place. Remote IP Address •...
-
Page 42: Network
Industrial Cellular VPN Router NR500 Series User Manual 4.5 Network 4.5.1 Firewall Firewall rules are security rule-sets to implement control over users, applications or network objects in an organization. Using the firewall rule, you can create blanket or specialized traffic transit rules based on the requirement. - Page 43 Industrial Cellular VPN Router NR500 Series User Manual Firewall->ACL Description • Add a description for this rule. Protocol • All: Any protocol number. TCP: The TCP protocol. UDP: The UDP protocol. TCP & DUP: both TCP and UDP protocol ICMP: The ICMP protocol. Source Address •...
- Page 44 Industrial Cellular VPN Router NR500 Series User Manual Local Port • Sets the LAN port number range used when forwarding to the destination IP address. Firewall->DMZ Enable • Check this box to enable DMZ function. Remote Address • Optionally restricts DMZ access to only the specified WAN IP address. NOTE: If set to 0.0.0.0/0, the DMZ is open to all incoming WAN IP addresses.
-
Page 45: Route
Industrial Cellular VPN Router NR500 Series User Manual 4.5.2 Route Static Routing refers to a manual method of setting up routing between networks. Select the Static Routing tab to add static routes to the Static Route Table. Please refer current route table as below. Route->Route Table Information Destination •... -
Page 46: Ip Passthrough
Industrial Cellular VPN Router NR500 Series User Manual IP Address • Enter the IP address of the destination network. Netmask • Enter the subnet mask of the destination network. Gateway • Enter the IP address of the local gateway. Interface •... -
Page 47: Applications
Industrial Cellular VPN Router NR500 Series User Manual 4.6 Applications 4.6.1 DDNS DDNS is a system that allows the domain name data of a computer with a varying (dynamic) IP addresses held in a name server to be updated in real time in order to make it possible to establish connections to that machine without the need to track the actual IP addresses at all times. -
Page 48: Sms
Industrial Cellular VPN Router NR500 Series User Manual Check IP Path • Check IP Path for custom type. Enable SSL • Enable SSL for connection. Username • Enter the user name used when setting up the account. Used to login to the Dynamic DNS service. Password •... -
Page 49: Schedule Reboot
Industrial Cellular VPN Router NR500 Series User Manual 4.6.3 Schedule Reboot Schedule reboot allows user to define the time for router reboot itself. Application->Schedule Reboot Enable • Check this box to enable schedule reboot feature. Time to Reboot • Enter the time of each day to reboot device. Format: HH(00-23):MM(00-59). Day to Reboot •... -
Page 50: Vpn
Industrial Cellular VPN Router NR500 Series User Manual 4.7 VPN 4.7.1 OpenVPN OpenVPN is an open source virtual private network (VPN) product that offers a simplified security framework, modular network design, and cross-platform portability. You could review all OpenVPN connection as below. VPN->OpenVPN->Status Enable •... - Page 51 Industrial Cellular VPN Router NR500 Series User Manual VPN->OpenVPN Enable • Check this box to enable OpenVPN tunnel. Description • Enter a description for this OpenVPN tunnel. Mode • Select from “Client” or “P2P”. Protocol • Select from “UDP” or “TCP Client”. Connection Type •...
- Page 52 Industrial Cellular VPN Router NR500 Series User Manual Enter the negotiate port on OpenVPN server. Authentication Method • Select from "X.509", "Pre-shared", "Password", and "X.509 And Password". Encryption Type • Select from "BF-CBC", "DES-CBC", "DES-EDE-CBC", "DES-EDE3-CBC", "AES-128-CBC", "AES-192-CBC" and "AES-256-CBC". Username •...
- Page 53 Industrial Cellular VPN Router NR500 Series User Manual VPN->OpenVPN->Advanced Settings Enable NAT • Check this box to enable NAT, the source IP of host behind router will be disguised before accessing the remote end. Enable PKCS#12 • It is an exchange of digital certificate encryption standard, used to describe personal identity information.
- Page 54 Industrial Cellular VPN Router NR500 Series User Manual VPN->OpenVPN->X.509 Certificate Connection Index • Displays the current connection index for OpenVPN channel. CA Certificate • Import CA certificate file. Local Certificate File • Import Local Certificate file. Local Private Key • Import Local Private Key file.
-
Page 55: Ipsec
Industrial Cellular VPN Router NR500 Series User Manual 4.7.2 IPSec IPSec facilitates configuration of secured communication tunnels. The various tunnel configurations will be displayed in the Tunnel Table at the bottom of the page. All tunnels are create using the ESP (Encapsulating Security Payload) protocol. VPN->IPSec->Status Enable •... - Page 56 Industrial Cellular VPN Router NR500 Series User Manual VPN->IPSec Enable • Select Enable will launch the IPSec process. Description • Enter a description for this IPSec VPN tunnel. Remote Gateway • Enter the IP address of the remote endpoint of the tunnel. IKE Version •...
- Page 57 Industrial Cellular VPN Router NR500 Series User Manual VPN->IPSec Encryption Algorithm (IKE) • Select 3DES AES-128, AES-192, or AES-256 encryption. Hash Algorithm (IKE) • Select from MD5, SHA1, SHA2 256, SHA2 384 or SHA2 512 hashing. Diffie-Hellman Group (IKE) • Negotiate (None) or use 768 (Group 1), 1024 (Group 2), 1536 (Group 5) or 2048 (Group 14) etc.
-
Page 58: Gre
Industrial Cellular VPN Router NR500 Series User Manual 4.7.3 GRE Generic Routing Encapsulation (GRE) is a protocol that encapsulates packets in order to route other protocols over IP networks. It’s a tunneling technology that provides a channel through which encapsulated data message could be transmitted and encapsulation and decapsulation could be realized at both ends. -
Page 59: Maintenance
When newer versions of NR300 firmware become available, the user can manually update the unit by uploading a package to the unit. NOTE: The unit need manually reboots once the upload completes, thus taking the NR300 router out of service during approximately 1 minute. Unless otherwise stated, the user is not expected to take any special precautions. -
Page 60: Software
User Manual 4.8.2 Software When release a new feature(APP Package) of NR300 router, the user can manually install to the unit by uploading a package. Or user can uninstall this feature(APP Package) from router. NOTE: The unit need manually reboots once the upload/uninstall completes, thus taking the NR300 router out of service during approximately 1 minute. -
Page 61: System
Industrial Cellular VPN Router NR500 Series User Manual 4.8.3 System This section allows you to review the device system settings. System->General Hostname • User-defined router name, which might be use for IPSec local ID identify. User LED Type • Defined the User LED behavior. Time Zone •... - Page 62 Industrial Cellular VPN Router NR500 Series User Manual System->Account Administrator • Displays the name of current administrator, default as “admin”. Old Password • Enter the old password of administrator. New Password • Enter the new password of administrator. Confirm Password •...
- Page 63 Industrial Cellular VPN Router NR500 Series User Manual Syslog displays system logs that are stored in the log buffers. System->Syslog Log Location • Select the log store location to “RAM”. Log Level • Select the log output level from “Debug”, “Notice”, “Info”, “Warning” or “Error”. Enable Remote Syslog •...
- Page 64 Industrial Cellular VPN Router NR500 Series User Manual System->Telnet Telnet Port • Enter the port for telnet access. A well-known port for HTTP is port 23. System->SSH SSH Port • Enter the port for SSH access. A well-known port for HTTP is port 22. Allow Password Authentication •...
-
Page 65: Configuration
The Unit Configuration tab allows you to save parameters (settings in the Web interface) to a file. Conversely, if you have saved settings from the NR300 router to a file, you can Import these previously-saved configuration settings to the NR300 router as well. - Page 66 Industrial Cellular VPN Router NR500 Series User Manual Ping Count • Enter the ping times. Local IP Address • Enter the ping source IP address or leave it blank. Debug Tools->Traceroute Host Address • Enter a host IP address or domain name for traceroute. Max Hops •...
-
Page 67: Appendix A -Glossary
Industrial Cellular VPN Router NR500 Series User Manual Appendix A -Glossary APN: Access Point Name GPRS: General Packet Radio Service HSPA: High Speed Packet Access HSDPA: High-Speed Downlink Packet Access HSUPA: High-Speed Uplink Packet Access LTE: 3GPP Long Term Evolution IMEI: International Mobile Equipment Identity ICCID:... -
Page 68: Appendix B -Q&A
Check the cellular page confirm modem is detected correctly or not. • Cannot detect SIM card Phenomenon NR300 Router cannot detect SIM card, cellular is not failed to connect to base station. Possible Reason SIM card damage. • SIM bad contact. -
Page 69: Ipsec Vpn Established, But Lan To Lan Cannot Communicate
Industrial Cellular VPN Router NR500 Series User Manual IPSec VPN established, but LAN to LAN cannot communicate Phenomenon IPSec VPN established, but LAN to LAN cannot communicate Possible Reason Both subnets are not match the interested traffic. • IPSec second phase (ESP) settings is not match. •... -
Page 70: Appendix D - Cli
Appendix D - CLI Command-line interface (CLI) is a software interface that provide another configurable way to set parameters on our router. We could use Telnet or SSH connect to our router for CLI input. NR300 CLI Access navigateworx.router login: admin Password: admin >... - Page 71 Industrial Cellular VPN Router NR500 Series User Manual How to Configure the CLI CONTEXT SENSITIVE HELP [?] - Display context sensitive help. This is either a list of possible command completions with summaries, or the full syntax of the current command. A subsequent repeat of this key, when a command has been resolved, will display a detailed reference.