Table of Contents
Advertisement
Quick Links
Year of Manufacture:
C-1000 Screen Coater
Assembly, Operating, and Maintenance Instructions
Safety
Assembly/Operation
Drive Chain
Troubleshooting
Warranty
Serial Number:
VTX
(Please log your machine's serial number and date of purchase for future reference.)
20____
Date:____
Vastex International, Inc.
7 Emery Street
Bethlehem, Pa. 18015 USA
Phone# 610 625-2702 Fax# 610 625-2775
Web Site www.vastex.com
Authorized Representative in Europe:
Pg #
Certification Experts BV
Nieuwstad 100 1381 CE Weesp,
The Netherlands
2
Tel : + 31 (0) 294 – 48 33 55
Fax : + 31 (0) 294 – 41 46 87
3-5
6
Vastex E-mail assistance
7
Purchasing & Product Info:
sales@vastex.com
Electrical Support:
8
stech@vastex.com
Tech Support, Mechanical Setup, and Operation:
techsupport@vastex.com
/
/
____
______
Screen Printing Issues & Support:
printech@vastex.com
Doc. # 01-18-006C
Original Instructions
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VASTEX C-1000
Summary of Contents for VASTEX C-1000
- Page 1 Doc. # 01-18-006C 20____ Year of Manufacture: Original Instructions C-1000 Screen Coater Assembly, Operating, and Maintenance Instructions Vastex International, Inc. 7 Emery Street Bethlehem, Pa. 18015 USA Phone# 610 625-2702 Fax# 610 625-2775 Web Site www.vastex.com Authorized Representative in Europe:...
- Page 2 Only qualified technicians should be allowed to make repairs on the VASTEX C-1000. The C-1000 should not be loaded with a screen larger than 36” or with a weight exceeding 10 lb. Maintenance 1) Every month, inspect the Screen Coater for loose bolts and tighten if necessary.
- Page 3 Each installation may be unique. Vastex recommends securely attaching your C-1000 to a wall or sturdy structure. Vastex supplies each C-1000 with various hardware to attach the unit to a wall. The method shown here is our recommendation. 1) Your C-1000 comes fully assembled from the factory.
- Page 4 Scoop Coater Holder (Above) Scoop Coater Holder installed. 3) To install a screen onto the C-1000, install the Upper Screen Holder at the appropriate position (See Step 1). Then push down on the Lower Screen holder with the bottom of the screen, pivot the screen in, and guide it into the Upper Screen Holder.
- Page 5 Assembly/Operation 4) Place operating pedals at a convenient location for the operator. Be sure not to pull the wires taunt when placing. Up Pedal NEVER PRESS BOTH PEDALS AT ONCE. THIS WILL CAUSE FUSES TO FAIL. Down Pedal Power Light: Illuminated when machine is on. Power Switch: Turns on machine.
- Page 6 It is important to regularly inspect the chain to determine the chain is properly tensioned, and not sagging. The C-1000 carriage is designed to slip if an obstruction is present during travel. If the carriage slips under normal operation, please contact Vastex technical support.
- Page 7 Troubleshooting Screen Carriage does not move up or down: Check the fuses behind the right access panel on the control box. To access the fuses, loosen the (4)#8 Sheet Metal Screws, and slide the cover to the right, then off. System Fuses (See wiring diagram for details) Referred to as #1-#6 Top-Bottom...
- Page 8 The defective part or parts will be repaired or replaced at the discretion of Vastex International, Inc. If the equipment in question is less than one (1) year old, it will be shipped to the customer at no charge, with an RGA issued by Vastex for the defective part. The defective part must be shipped back to Vastex freight prepaid within 30 days or the account will be billed.
Need help?
Do you have a question about the C-1000 and is the answer not in the manual?
Questions and answers