Advertisement
Table of Contents
20____
Year of Manufacture:
C-100 Screen Coater
Assembly, Operating, and Maintenance Instructions
Shown with op onal stand
Screen Coater Assembly
Stand Assembly (optional)
Safety, Operation, and Maintenance
Warranty
Electrical Drawing #:
Serial Number:
VTX
(Please log your machine's serial number and date of purchase for future reference.)
Pg #
2-3
4-5
6
7
Rev:______
/
/
Date:____
____
______
Original Instruc ons
Vastex International, Inc.
7 Emery Street
Bethlehem, PA 18015 USA
Phone# 610 625-2702 Fax# 610 625-2775
Web Site www.vastex.com
Authorized Representative in Europe:
Certification Experts BV
Nieuwstad 100 1381 CE Weesp,
The Netherlands
Tel : + 31 (0) 294 – 48 33 55
Fax : + 31 (0) 294 – 41 46 87
Vastex E-mail assistance
Purchasing & Product Info:
sales@vastex.com
Electrical Support:
stech@vastex.com
Tech Support, Mechanical Setup, and Operation:
techsupport@vastex.com
Screen Printing Issues & Support:
printech@vastex.com
Doc. # 01‐18‐005b
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VASTEX C-100
Summary of Contents for VASTEX C-100
- Page 1 20____ Doc. # 01‐18‐005b Year of Manufacture: Original Instruc ons C-100 Screen Coater Assembly, Operating, and Maintenance Instructions Shown with op onal stand Vastex International, Inc. 7 Emery Street Pg # Bethlehem, PA 18015 USA Phone# 610 625-2702 Fax# 610 625-2775 Screen Coater Assembly Web Site www.vastex.com ...
- Page 2 Assembly Tools Needed: (1) Philips Head Screwdriver, (1) Flat Blade Screwdriver, (1) 7/16 wrench Mount Plate 1) Remove all parts from the box they were shipped in. For Wall Mount Units: 2) Attach the Mount Plate to a wall in your shop. Use 3 screws with wall anchors.
- Page 3 Upper Screen Holder Location Spine 7) To install a screen onto the C-100, install the Upper Screen Holder at the appropriate position (See Step 6). Then push down on the Lower Screen holder with the bot- tom of the screen, pivot the screen in and guide it into the...
-
Page 4: Stand Assembly
Stand Assembly Hardware List: Tools Required: A- 1/4-20 x 1/2” Hex Head Bolts (8) 7/16”, 1/2” & 9/16” Wrench B- 1/4-20 Serrated Nuts (9) C- 1/4-20 x 2-1/4” Hex Head Bolt (1) Adjustable Wrench D– 3/8-16 Serrated Nuts (4) ... - Page 5 Stand Assembly cont’d 5) Carefully slide the entire C-100 Assembly down onto the Round Post. Lower it down to the desired working height of the unit. Do Not Over Tighten 6) Tighten the 1/4-20x1/2” bolt on each Stand Mount. Do not Over Tighten these bolts as you can damage the Stand’s Round Post.
-
Page 6: Safety Instructions
VASTEX Screen Coater is intended for the coating of screen printing screens. Do not use for any other purpose unless authorized by Vastex International, Inc. Use of this equipment for any other purpose can be dangerous and may cause damage to this equipment voiding the warranty. - Page 7 The defective part or parts will be repaired or replaced at the discretion of Vastex International, Inc. If the equipment in question is less than one (1) year old, it will be shipped to the customer at no charge, with an RGA issued by Vastex for the defective part. The defective part must be shipped back to Vastex freight prepaid within 30 days or the account will be billed.
Need help?
Do you have a question about the C-100 and is the answer not in the manual?
Questions and answers