Summary of Contents for Samsung AC KNZDCH/AA Series
Page 1
Multiposition AHU KNZDCH/AA Air Conditioner installation manual imagine the possibilities Thank you for purchasing this Samsung product. EN ES FR...
Indoor unit installation Location Drain pipe installation Right side of unit 30" minimum Clearance - Access for service Vertical installation Horizontal installation...
Page 8
Indoor unit installation Return air requirements 0" 0" Return Air Requirements For A/C and HP Air Handlers 1/3 HP Blower Motor For A/C and HP Air Handlers 1/2 HP Blower Motors For A/C and HP Air Handlers with Electric Heat use 3/4 HP Blower Motor...
Page 9
Return air requirements Closet Wall Typical Closet Installations Upflow Accessory Filter Box Kit NOTE ADJUSTMENT KNOB ADJUSTMENT KNOB FOR 1" OR 2" FILTER FOR 1" OR 2" FILTER Accessory Air Filter Box for 1” or 2” Air Filters. Filter Size Adjustment knob is on both sides. FILTER BASE ASSEMBLY KIT MODEL NUMBERS - FIELD INSTALLED, PURCHASED SEPARATELY...
Page 10
Indoor unit installation Arrangement: Airflow Airflow Horizontal left arrangement Upflow application...
Page 11
Horizontal application Refrigerant pipe Horizontal right conections (left to right) drain pan opening Horizontal left (right to left) drain connections Horizontal right application (left to right) Evap. In Temperature Sensor Move drain pan to right side of coil...
Performing leak test & insulation Leak test LEAK TEST WITH NITROGEN (before opening valves) LEAK TEST WITH R-410A (after opening valves) CAUTION Leak check Insulation T13.0mm (0.51”) or thicker Leak check Acrylonitrile Butadien Rubber NBR [T13.0mm (0.51”) or thicker] Insulation NOTE Insulation Liquid pipe...
Page 14
Performing leak test & insulation Insulation Type (Cooling/Heating) General [30°C (86°F), High humidity [30°C Outer diameter 85% or below] (86°F), more than 85%] Pipe Remarks EPDM, NBR inch inch inch Liquid pipe Gas pipe...
Wiring Work WARNING Power supply wiring Wiring diagram Indoor Unit 1(L) 2(N) 1(L) 2(N) Cable clmap Cable clmap Communication cable Indoor Power Main power cable Outdoor Unit Between Indoor and Outdoor Connection cable Specifications(Common in use)
Page 18
Wiring Work Terminal Block SPEC (Indoor) AC POWER : M4 SCREW COMMUNICATION : M4 SCREW 0.43(8.4) 0.43(8.4) 0.51(9.5) 0.51(9.5) WARNING Single circuit line wiring connections CAUTION Left side Right side A - Power conduit connection opening (must use when installing accessory electric heat kit). B - Power conduit connection opening (do not use when installing accessory electric heat kit).
Page 19
Power supply wiring with accessory electric heat kit Power conduit connection openings...
Page 20
Wiring Work Power supply wiring with accessory electric heat kit Ground Lug Breaker 6 Pin Plug V-AHU Control Box (single circuit) Insulation (wrapped Wire tie around pipe and sensor) (to secure sensor to pipe) liquid pipe Liquid pipe Sensor wire Sensor Wire tie (to secure insulation) NOTE:...
Page 22
Wiring Work Communication wiring connections ATTENTION PBA ground screw/connection to chassis F1/F2 communication connection terminals Supply power ground connection point 1(L)/2(N) high voltage connection terminals Selecting compressed ring terminal Silver solder Nominal Nominal dimensions dimensions Standard Standard Standard Standard Allowance Allowance Allowance Min.
Blower CFM tables AC018KNZDCH/AA,AC024KNZDCH/AA,AC030KNZDCH/AA,AC036KNZDCH/AA,AC042KNZDCH/AA,AC048KNZDCH/ AA,AC054KNZDCH/AA Motor Tap P(inwg) Motor Tap P(inwg) 444444444...
Setting an indoor unit address and installation option The procedure of option setting Entering mode for Option setting setting option mode Step 1. Entering mode to set option Step 2. The procedure of option setting CAUTION...
Page 34
Setting an indoor unit address and installation option Option setting Status...
Page 35
Option setting Status Step 3. Check the option you have set → → → → → → → → → Step 4. Input option Step 5. Check operation...
Page 36
Setting an indoor unit address and installation option Setting an indoor unit address (MAIN/RMC) 1(L) 2(N) CAUTION...
Page 37
Setting the indoor unit option code Data bit Page number Option Code Main Menu Sub-menu 1 2 3 1 2 3 4 5 6 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 ✴ ✴ ✴ ✴ ✴ Page number SEG7 SEG8 SEG9 SEG10 SEG11 SEG12...
Page 38
Setting an indoor unit address and installation option Setting an indoor unit address Data bit 1 2 3 4 5 6 NOTE NOTE Setting an indoor unit installation option NOTE...
Page 40
Setting an indoor unit address and installation option Option SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 Option SEG19 SEG20 SEG21 SEG22 SEG23 NOTE CAUTION Electronic heater should not be installed. Discharge side Suction side Air Flow Indoor unit...
Troubleshooting LED Display on the receiver & display unit...
Page 42
Troubleshooting Flickering X Off If you turn off the air conditioner when the LED is flickering, the LED is also turned off.
Page 43
Wired remote controller If an error occurs, is displayed on the wired remote controller. If you would like to see an error code, press the Test button. Error Contents Error type mode Indoor unit communication error Communication error Duplicated address setting error Communication error No response error address from indoor unit Communication error...
Page 44
Troubleshooting Error Contents Error type mode [Inverter] Compressor startup error Outdoor unit protection control error [Inverter] Total current error/PFC over current error Outdoor unit protection control error OLP Overheat and Comp. Stop Outdoor unit protection control error [Inverter] IPM over current error Outdoor unit protection control error Compressor V limit error Outdoor unit protection control error...