Advertisement
Quick Links
HVLP AIR CAP AND FLUID NOZZLE CHART
MODEL
Press /
AIR CAPS
NO.
Siphon
23-1008
pressure
23-1010
pressure
23-1012
pressure
23-1013
pressure
L300H
23-1014
pressure
23-1015
pressure
23-1017
pressure
23-1019
pressure
23-1022
pressure
Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)
*Note: Air cap test gages are available to confirm HVLP compliance.
*Gun inlet pressures may vary as required by application
**When using optional gun regulator, inlet pressure changes to 45psi
Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708
*MAX GUN
FAN
INLET PRESS.
CONTROL
FOR HVLP
40**
40**
40**
40**
60-1502 (#2)
40**
40**
40**
40**
40**
www.spraycat.com
L L L L L ynx 300H
ynx 300H
ynx 300H
ynx 300H
ynx 300H
PRESSURE FEED SPRAY GUN
SCFM @
AIR CAP
MAX GUN
RING
INLET
13.5
33-0208 0.8mm (.022")
13.5
33-0210 1.0mm (.040")
13.5
33-0212 1.2mm (.046")
13.5
33-0213 1.3mm (.052")
Included
13.5
33-0214 1.4mm (.055")
13.5
33-0215 1.5mm (.059")
13.5
33-0217 1.7mm (.070")
13.5
33-0219 1.9mm (.075")
13.5
33-0222 2.2mm (.086")
PRODUCT INFORMATION
AVAILABLE FLUID
NOZZLES TIPS
marking on needle
NEEDLES /
40-1308 (308)
40-1310 (310)
40-1312 (312)
40-1313 (313)
40-1314 (314)
40-1315 (315)
40-1317 (317)
40-1319 (319)
40-1322 (322)
Advertisement
Related Manuals for C.A. Technologies Lynx 300H
Summary of Contents for C.A. Technologies Lynx 300H
- Page 1 L L L L L ynx 300H ynx 300H ynx 300H ynx 300H ynx 300H PRESSURE FEED SPRAY GUN PRODUCT INFORMATION HVLP AIR CAP AND FLUID NOZZLE CHART *MAX GUN SCFM @ MODEL Press / AIR CAP AVAILABLE FLUID NEEDLES / AIR CAPS INLET PRESS.
- Page 2 L300H L300H L300H L300H L300H Operation and Maintenance Instructions for Spray Guns Operation 1. Connect air supply hose at handle of gun. 2. Connect a pressurized fluid supply to the gun fluid inlet. 3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.
- Page 3 HVLP AIR CAP TEST GAGES 23-1008-G 23-1010-G 23-1012-G 23-1013-G L300H 23-1014-G GUNS 23-1015-G 23-1017-G 23-1019-G 23-1022-G ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION See Air Cap Chart Air Cap** 60-204 Needle Return Spring* See Air Cap Chart Fluid Nozzle Tip** 60-201 Rear Bushing...
- Page 4 FLUID NOZZLE / AIR CAP SELECTION CHARTS LYNX Series 300H - Pressure Feed Guns L300H HVLP SPRAY GUN FLUID ORIFICE x MAXIMUM MATERIAL TYPE PRESS. / SIPHON AIR CAP PATTERN WIDTH Very Thin less than 16 sec. Zahn #2 1.0 mm x 1010 inks , dyes, solvents, stains Thin...