Subscribe to Our Youtube Channel
Related Manuals for Shire Forget-Me-Not Arbour
Summary of Contents for Shire Forget-Me-Not Arbour
- Page 1 Mass: 52.2 kg Batch No: XXXX © Forget-Me-Not Arbour These instructions are for your safety. Please read through them thoroughly before use. PLEASE KEEP THIS LEAFLET FOR FUTURE REFERENCE...
-
Page 2: Table Of Contents
Let’s get started... Important information... Safety Preparation of base Warranty Care, maintenance & Recycling In more detail... Parts List Fascia & Nail List Detailed Technical Drawing 08-09 Hardware Chart Before you start Assembly Instructions 12-24 For a copy of the instructions or a copy in another language please send an email or write to the address below. -
Page 3: Safety
Safety Check that you have noted all the following instructions: We advise the use of non slip protective gloves throughout the assembly process. We advise the use of steel capped protective footwear throughout the assembly process. We advise that you use a helper to hold the glass in position whilst you nail the beading in place. -
Page 4: Preparation Of Base
Base and Warranty Preparation of base... We recommend that the base onto which your building will stand should be at least 75mm larger in each direction than the total floor size of the building. Actual floor area of the building: 1236mm x 654mm ... -
Page 5: Care, Maintenance & Recycling
Care, Maintenance and Recycling The 5 golden rules of care: Ensure your base is level and firm. Ensure the building is not sitting directly on the ground using damp proof membrane or the optional timber base. Ensure every piece of timber and surface, especially that is hidden upon assembly, is treated with a top quality wood preservative at least twice (before assembly). -
Page 6: Parts List
Stacked Parts List Description (part No ) - Qty... -
Page 7: Fascia & Nail List
Fascia and Nail Bag Parts List Description (part No ) - Qty... -
Page 10: Hardware Chart
Nail bag contents Description (part No ) - Qty Hardware Chart Scale 1:1 40mm Round Head Nail (A0025) x 14 25mm Posi-Drive Screw (A0032) x 03 40mm Posi-Drive Screw (A0032) x 09 60mm Posi-Drive Screw (A0035) x 45 Building Photographs It will be greatly appreciated if you could forward images of your... -
Page 11: Before You Start
Before you start... Things to check before you start: Ensure your base is ready – See page 4. Check all parts as listed in the parts lists. Read the instructions fully before starting work. Follow all the health and safety guidelines. When you see the drill icon Only ever drill through the first piece of framework which will be a... -
Page 12: Assembly Instructions
Assembly instructions: These instructions are for your safety. Please read through them thoroughly before use. Treat all the parts before assembly – see page 5! The “Panel layout” is showing you how to position the panels. GB-IE The Panels FIT INBETWEEN THE CORNER POSTS! A06342 A5921 A5921... - Page 13 Lay the Plain Panel (A06342) flat. GB-IE Screw two Corner Posts (A5921) to the sides as below, using 6x 60mm Screws (A0035) within the pilot holes drilled in the previous step. Step 1 (A06342)x01 Corner Post (A5921)x02 60mm Screws (A0035)x06 Flat edge sits flush with outside cladding.
- Page 14 Drill one Window Panel (A5911) as below. Making sure the outside cladding is facing inwards GB-IE and flush with the flat face of the corner post, fix with 3x 60mm Screws (A0035) using the pilot holes previously drilled. Then screw another Corner Post (A5921) as below, using the pilot holes.
- Page 15 Drill the other Window Panel (A5911) as below. Place the panel making sure the cladding is GB-IE facing inwards and is flush with the corner post. Fix with 3x 60mm Screws (A0035). Then fix the last Corner Post (A5921) to the window panel using 3x 60mm Screws (A0035) within the pilot holes.
- Page 16 Measure and mark from the bottom of the Window Panels up 368mm. Drill and screw the two GB-IE 34x34x590 (A5923) so that the top of the timber sits flush at the 368mm mark as below. Drill and screw the 34x34x1052 (A5922) to the Plain Panel so that the top is flush with the 34x34x590 timber.
- Page 17 Drill through the seat frame made in Step 05 as below. Carefully stand the building up and GB-IE place the Seat Base (A5912) onto the frame as below. Make sure the 12mm overhang on the seat base is facing forward. Secure the base using 7x 60mm Screws (A0035) using the pilot holes drilled.
- Page 18 Place the RH Seat Back (A5889) onto the Seat Base as below. Drill and screw through the GB-IE Window Panel so the screws go into the side bar of the Seat Backing. Measure and mark on the Plain Panel where the middle bar of the seat back sits. Then drill and screw using 2x 60mm Screws (A0035).
- Page 19 Place the Gable (A06343) onto the Plain Panel as below. Make sure the cladding is facing inwards and is flush with the cladding on the Plain Panel. Make sure the gable is central and equal on both sides. Fix through the plain panel as below using 2x 60mm Screws (A0035). Sits equal both sides Gable (A06343)x01...
- Page 20 Drill both Roof Panels (A5914) as below. Fix the 44x44x722 (A5924) to the top of one roof GB-IE panel as below, make sure the edge is flush with the roof panel frame work. Fix with 3x 60mm Screws (A0035). Fix the second roof panel with 3x 60mm Screws (A0035) as below. The 44x44x722 piece of timber should not be visible once both panels are fixed.
- Page 21 Nail one Roof Capping (A5925) so it sits flush the edge of the 44x44x722 bar as below. Then nail the second Roof Capping (A5925) so it overlaps the other as below. Fix with 40mm Nails (A0025). Roof Capping (A5925)x02 40mm Nails (A0025)x06...
- Page 22 Place the assembled Roof Panels onto your building as below. GB-IE The corner posts should fit in between the Roof Panels. The bar inside the Roof Panel should rest upon the Window Panels. Screw from the outside using 3x 60mm Screws (A0035) in each side as below. 60mm Screws (A0035)x06 Screws go into Window Panels...
- Page 23 GB-IE Fix the Fascia (A06344) to the front of your building as below. Fix with 3x 40mm Nails (A0025) in each. Fix the Diamond (A5913) centrally using 2x 40mm Nails (A0025) as below. Fascia (A06344)x02 Diamond (A5913)x01 40mm Nails (A0025)x08...
- Page 24 GB-IE Drill and screw the Seat Fascia 1120 (A5920) to the seat base framework as below. Fix using 3x 25mm Screws (A0032), spaced evenly apart. Seat Fascia 1120 (A5920)x01 25mm Screws (A0032)x03...
Need help?
Do you have a question about the Forget-Me-Not Arbour and is the answer not in the manual?
Questions and answers