Advertisement
Quick Links
Models:
DV210AEW DV210AGW
DV220AEW DV220AGW
NOTICE: All Dryers Parts Change
6/2010: Motor Pulley, page 5;
Blower Housing, page 4
Display
dO
dE
FE
dF
hE or HE
bE
od
SUPPORT INFORMATION
Training — Plus One
http://my.plus1solutions.net/clientPortals/samsung/
Help — GSPN
http://service.samsungportal.com/
Samsung Product Support TV
http://support-us.samsung.com/spstv/howto.jsp
Customer information videos and chat programs
Programs for Fridges, Laundry, Ranges & D/W
IMPORTANT SAFETY NOTICE – "For Technicians Only" This service data sheet is
intended for use by persons having electrical, electronic, and mechanical experience
and knowledge at a level generally considered acceptable in the appliance repair trade.
Any attempt to repair a major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible, nor assume any liability for
injury or damage of any kind arising from the use of this data sheet.
Samsung 'Dryer' Diagnostic Code Quick Guide
Description
Dryer Thermistor Short
Sensed
Dryer Thermistor Open
Sensed
Door Open
Power source frequency
Error
Door Circuit Failure
Heater Error
Button Error
Over Dry
EEprom Fail
Fast Track Troubleshooting
Publication # tsDV210 Revision Date 06/27/2011
Trigger
The Thermistor resistance is
very low.
The Thermistor resistance is
very high.
Running the dryer with door
open
Invalid power source Frequency Check for: Non Utility power supply
Invalid state for more than 256
milliseconds
Invalid heating Temp in running
the dryer
PCB key closed for 75 sec.
Invaled Dry Time Excessive Dry
Time
Invalid state of Eeprom
communication
Electrical Dryers 240 VAC, 60 Hz, 30 Amps, 3
-wire or 4-wire installations
Gas Dryers 120 VAC, 60 Hz, 15 Amps, 3-wire
installations
Location consideration In the USA
All Dryers Must be vented to the outside.
Only rigid or flexible metal duct should be
used for venting.
Action Taken
Check for: Clogged lint screen,
Restricted vent system, Thermistor
resistance.
Check for: Clogged lint screen,
Restricted vent system, Thermistor
resistance.
Check for: Loose or open wire
terminals in Door Sense circuit.
Check for: Loose or open wire
terminals in Door Sense circuit.
Check for: Restricted vent system,
Thermistor resistance.
Check Display PCB for stuck button
Inspect seensor bars
Replace Main PCB
:
Advertisement
Related Manuals for Samsung DV210AGW
Summary of Contents for Samsung DV210AGW
- Page 1 NOTICE: All Dryers Parts Change 6/2010: Motor Pulley, page 5; Publication # tsDV210 Revision Date 06/27/2011 Blower Housing, page 4 Samsung 'Dryer' Diagnostic Code Quick Guide Display Description Trigger Action Taken...
- Page 4 CN2 Sub PCB Display 1 120vac N (Brn) 1 Motor #6 (Blk) 5-4 5VDC (Wht-Pnk) 1 Lamp (Vio) 2 Sub PCB (Wht) 2 Door Sw (Blu) 6-4 15VDC (Red-Pnk) 3 Sub PCB (Yel) Relay 1 1 Motor Belt Sw (Brn) 2 120vac L1 (Blk) Relay 6 1 Gas Hi Limit T-Stat (Blu)
- Page 5 SUBJECT: Dryer belt slides off the pulley when Gas Valve Testing manually rotated counter-clockwise (ccw) Unplug connectors and test valve terminals SYMPTOM: The dryer drum will not turn. On occa- sions, the customer will rotate the drum counter (its numbering is from the front terminal.) clockwise (CCW) to check for any remaining Check across terminals #1 and #3 (Booster Coil).
- Page 6 Testing Electric Heater circuit. Disconnect Blue wire from RY6, turn power on, start dryer read voltage between RY6 Blue wire and CN6 Green wire. Reading of 120VAC means a proper operating heater circuit. 0VAC means open in circuit. To test thermostats use ohm meter on lowest scale, any resistance replace component See page 4 for Main PCB layout for testing.
- Page 7 RY 6 RY 5 Testing Main PCB power output to Heating & Motor circuit. With motor running in the heating mode, read AC voltage across RY6 and RY5. Any voltage reading means Main PCB is defective. See page 4 for Main PCB layout for testing. RY 5 Testing Motor circuit.