Download Print this page

Enwork ZORI Installation Instructions Manual

Monitor lift

Advertisement

Quick Links

Z O R I
M O N I T O R
L I F T
I N S T A L L A T I O N
I N S T R U C T I O N S
M O N I T O R
L I F T
Z I 0 0 1 3
Zori Monitor Lift Installation Guide – Rev A.

Advertisement

loading
Need help?

Need help?

Do you have a question about the ZORI and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Enwork ZORI

  • Page 1 I N S T A L L A T I O N I N S T R U C T I O N S M O N I T O R L I F T Z I 0 0 1 3 Zori Monitor Lift Installation Guide – Rev A.
  • Page 2: Installation

    I N S T A L L A T I O N G U I D E P R E - I N S T A L L T I P S Place your tables in the desired configuration near its designated power source before starting. Utilize the cutout in the end panels to lift the tables if needed.
  • Page 3 G U I D E P A R T S A N D F A S T E N E R S I N C L U D E D Zori Monitor Lift Table Side Filler Panel (2x) Top Filler Panel–Single (1x) CYPxxxxxxx CYL-1887 CYL-1888-xS Top Filler Panel–End (2x)
  • Page 4 I N S T A L L A T I O N G U I D E P A R T S A N D F A S T E N E R S I N C L U D E D C O N T .
  • Page 5 I N S T A L L A T I O N G U I D E P A R T S A N D F A S T E N E R S I N C L U D E D C O N T .
  • Page 6 I N S T A L L A T I O N G U I D E T O O L S A N D S U P P L I E S R E Q U I R E D Drill/Driver Phillips Bit Square Bit...
  • Page 7 I N S T A L L A T I O N G U I D E A S S E M B L Y : O V E R V I E W Back-to-Back Ganging (Pages 6-9) Side-to-Side Ganging (Page 8 Figure 4.9) 4Trac Power (Page 10) Accessories - Mini CPU (Page 11)
  • Page 8 I N S T A L L A T I O N G U I D E A S S E M B L Y : G A N G I N G Remove all the Surface Lids. Note: Set aside hardware as it will be used again. F I G U R E 4 .
  • Page 9 I N S T A L L A T I O N G U I D E A S S E M B L Y : G A N G I N G Locate another table over the other end of the bottom Ganging Bracket, repeating steps 2 &...
  • Page 10 I N S T A L L A T I O N G U I D E A S S E M B L Y : G A N G I N G Install Panel Clips to the Side Filler Panel using the provided #8 x ¾”...
  • Page 11 I N S T A L L A T I O N G U I D E A S S E M B L Y : G A N G I N G Lay the Top Filler Panel onto the top Ganging Brackets, in between the Side Filler Panels.
  • Page 12 I N S T A L L A T I O N G U I D E A S S E M B L Y : 4 T R A C P O W E R (Adjacent table hidden for clarity) If applicable remove the Routing Hole Cover on the side of the leg and fish the provided Jumper through the cutouts of two adjacent tables.
  • Page 13 Vesa hole pattern. Bolts are NOT provided by Enwork. • Zip tie the CPU utilizing the slots in the Mini CPU Bracket. Zip ties are NOT provided by Enwork. F I G U R E 6 . 3...
  • Page 14 F I G U R E 6 . 4 5. Attach the Vesa Bracket to the back of your monitor. Note: Hardware is NOT provided by Enwork. F I G U R E 6 . 5 Attach the Monitor Shroud to the Lifting Column using the provided (2) ¼...
  • Page 15 I N S T A L L A T I O N G U I D E A S S E M B L Y : A C C E S S O R I E S – M O N I T O R &...
  • Page 16 I N S T A L L A T I O N G U I D E A S S E M B L Y : A C C E S S O R I E S – K E Y B O A R D &...
  • Page 17: Wire Routing

    I N S T A L L A T I O N G U I D E A S S E M B L Y : W I R E R O U T I N G – = CPU –...
  • Page 18 I N S T A L L A T I O N G U I D E A S S E M B L Y : W I R E R O U T I N G – = CPU –...
  • Page 19: A N D O P E R A T I O N

    I N S T A L L A T I O N G U I D E A S S E M B L Y : P A I R I N G A N D O P E R A T I O N Set the same DIP switch on each Control Box in the classroom by pressing down on the switches.
  • Page 20 I N S T A L L A T I O N G U I D E A S S E M B L Y : P A I R I N G A N D O P E R A T I O N F I G U R E 7 .
  • Page 21 I N S T A L L A T I O N G U I D E A S S E M B L Y : P A I R I N G A N D O P E R A T I O N To lock the Lifting Columns , press and hold the lock button for 3 seconds until the backlight flashes.
  • Page 22: Troubleshooting

    I N S T A L L A T I O N G U I D E T R O U B L E S H O O T I N G Q: The Control Box has no function • Check if the power supply is loose or disconnected. •...
  • Page 23 1.800.815.7251 www.enwork.com 12900 Christopher Dr. Lowell, MI 49331 Specifications subject to change without notice. Rev 09.2020...