Subscribe to Our Youtube Channel
Related Manuals for Constructor P90
Summary of Contents for Constructor P90
- Page 1 Installation manual P90 Pallet racking Read this installation manual carefully before start using the pallet racking. It is recommended to consult the manual continuously throughout the entire lifetime of the racking.
-
Page 2: Table Of Contents
Congratulations on your new P90 pallet racking from Constructor. It is very important that you follow the instructions in this manual, in order for your pallet racking to be fully functional and comply with current standards. The purpose of this installation manual is to provide warehouse personnel and management with important facts on the pallet racking, as well as precautions on potential risk areas. -
Page 3: Technical Information
Beam height (h) = 80, 90, 100, 120, 125, 140 and 150 mm. Other beam heights may occur. Max. load per supporting level has been calculated based on maximum deflection of L / 200. 1350 2700/2750 2700/2750 3600 1800/1850/1900 © Constructor 2020... -
Page 4: Upright Installation
730 mm 2 - Diagonal 1144 mm 908 mm 1198 mm 954 mm 3 - Diagonal 1264 mm 1056 mm 1313 mm 1096 mm h=7000 h=6500 h=6000 h=5500 h=5000 h=4500 h=4000 h=3500 h=3000 h=2500 h=2000 P90 Pallet racking | Installation manual... - Page 5 4th diagonal bracing. Anchorage should be in the middle slot. If anchoring in other floors other than concrete, please contact Constructor for guidance. Bolt M10x25 + bracket, nut M10 nyloc NOTE! Prior to the pallet racking being anchored...
- Page 6 Upright protector To be installed with a free clearance of min. 50 mm between upright and protector peak, inside. 50 mm The protector is anchored in concrete floor using concrete screw M10. P90 Pallet racking | Installation manual...
-
Page 7: Product Safety And Responsibility
If any support for the protector is applied then clearance can be reduced to 25 mm. Product safety and responsibility When purchasing P90 directly with Constructor for production errors). The total installation or through a Constructor dealer, Constructor responsibility will pass on to the person having... -
Page 8: Security Questions
An important part of the initiatives to obtain For installation of pull out units it is very highest level of security is to equip the pallet important to obey the following: racking with safety accessories, like frame protector, upright protector etc. P90 Pallet racking | Installation manual... -
Page 9: Inspecting The Racking
If you have any questions, please contact your local representative. Buyer or user is responsible for above inspections to be carried out. When repairing pallet racking, damaged supporting parts must be replaced. © Constructor 2020... -
Page 10: Primary Control Points
Use the load sign Check that no to check that the uprights are pallet racking is damaged. Install protectors on the not overloaded. uprights. Make sure that the aisles are properly dimensioned. P90 Pallet racking | Installation manual... -
Page 11: Key Max Measurements
Bent uprights, in depth Upright prolongation line, in depth If deformations / folds arise, the part must be changed. Beams Frame grid Bracing is adjustable. 10 mm Max. deflection when loaded: L/200 10 mm 10 mm Max. deflection: L/400 © Constructor 2020... - Page 12 • P90 Pallet racking, tested and approved according to European FEM norms. For all types of racking installations. From picking to high rise. From palletflow to mobile pallet racking. • Hi280 shelving, the most versatile shelving system on the market, with a comprehensive selection of accessories •...
Need help?
Do you have a question about the P90 and is the answer not in the manual?
Questions and answers