Related Manuals for Loos & Co Cableware Locoloc HC-S724H
Summary of Contents for Loos & Co Cableware Locoloc HC-S724H
- Page 1 Locoloc ® Cutting Tools HC-S724H Handheld Battery-Powered Cutter Operator’s Manual...
-
Page 3: Table Of Contents
CONTENTS Title Page Specifications Standard Accessories Safety Guideline Power Supply Connection General Information Guide Operating Instructions Blade Sharpening Tool Troubleshooting Battery Troubleshooting Warranty www.loosnaples.com Toll Free: 800-321-LOOS (5667) -
Page 4: Specifications
SPECIFICATIONS FEATURES Lightweight and Portable • Works in Any Position • • 180° Rotational Head CUTTING TOOL Output: 8 ton Weight: 11 lbs. Size: 13.2”L x 14.7”H x 3.3”W Jaw Opening: .95” CAPACITIES Wire Rope: 7/8” (22 mm) Rebar (Sc 40): 5/8”... -
Page 5: Standard Accessories
STANDARD ACCESSORIES BATTERY CARTRIDGE BATTERY CHARGER CARRYING CASE www.loosnaples.com Toll Free: 800-321-LOOS (5667) -
Page 6: Safety Guideline
SAFETY GUIDELINES This guide presents the setup, use, maintenance and troubleshoot- ing of the charger along with instructions for conditioning your bat- teries. Before using the battery charger, read all instructions and caution- ary markings on the battery charger, battery and on any product using the battery. -
Page 7: Power Supply Connection
POWER SUPPLY CONNECTION The power supply uses a nominal 120 volt circuit. The power supply manages and conditions the power input to the charger. The power supply does not use a resettable or replaceable fuse. If a power surge occurs the power supply temporarily interrupts the current supply until the condition is corrected. -
Page 8: General Information Guide
GENERAL INFORMATION GUIDE The following steps are guidelines for safe operation of the cutters. Please take the time to review them as these are helpful hints that have been accumulated over the years. 1. After inserting a battery pack, check if it is securely in place by pushing it gently, and a “click”... - Page 9 GENERAL INFORMATION GUIDE securely latched before cutting. If the latch is not secured, the blade will push open the cutter head and damage both the body head and blade. This causes the outside ear to the blade to break on an angle. In some cases, the whole cutter head may crack in half.
- Page 10 GENERAL INFORMATION GUIDE 15. Always cut the material at a 90° angle to the blade. Any other angle may cause the blade and head shear to fracture. See illustration below. 16. Head rotates 180° for proper cut angle. www.loosnaples.com Toll Free: 800-321-LOOS (5667)
-
Page 11: Operating Instructions
OPERATING INSTRUCTIONS 1. Before cutting, make sure the material being cut is within the proper cutting capacity of the tool being used. 2. Open cutter head by lifting latch. 3. Insert material between cutter head and blade and secure latch. It is important that you check the latch for proper en- gagement before continuing with the cut. -
Page 12: Blade Sharpening
BLADE SHARPENING INSTRUCTIONS www.loosnaples.com Toll Free: 800-321-LOOS (5667) -
Page 13: Tool Troubleshooting
TOOL TROUBLESHOOTING www.loosnaples.com Toll Free: 800-321-LOOS (5667) - Page 14 TROUBLESHOOTING CUTTER 1. Problem: Small wire strands or pieces of cable or debris get jammed between the cutter head and blade, not allowing the blade to retract. Solution: A) Hold release lever down while tapping on the ram with a block of wood and a hammer. If this does not work or tool continues to hang up, proceed to step “B”.
-
Page 15: Battery Troubleshooting
BATTERY TROUBLESHOOTING www.loosnaples.com Toll Free: 800-321-LOOS (5667) -
Page 16: Warranty
WARRANTY Huskie Tools products carry a warranty that makes us a leader in the tool industry. PRODUCT WARRANTY Series 7 Pro Line battery operated products 5 Years IL-7ND 3 Years ECO-Series products 1 Year Power Tools 3 Years Batteries (BP-185) 3 Years Chargers (CH-185, CH-285) 3 Years... - Page 17 WARRANTY (CONT.) Huskie reserves the right to determine all warranty claims. Huskie will not waranty tools containing parts or batteries not originally supplied by Huskie. Failure due to misuse, improper maintenance, misapplication, not following instructions or warnings, abuse or repairs attempted by anyone other than Huskie Tools, Inc.
- Page 18 WARRANTY (CONT.) Complete Support Services Our customers have direct access to us for training, service, and problem solving. As specialists in tools, we maintain a trained repair staff and a large stock of parts. This contrasts with many tool suppliers who carry tools as a sideline without offering support services.
- Page 20 901 Industrial Blvd • Naples, FL 34104 Tel: (239) 643-LOOS • Fax (239) 643-4558 E-mail: sales@loosnaples.com • Website: www.loosnaples.com INST-36 Rev. 7/11/2019...