Related Manuals for Loos & Co Locoloc HC-16
Summary of Contents for Loos & Co Locoloc HC-16
- Page 1 ocoLoc ® ® Cutting Tools HC-16 & HC-16PL Handheld Hydraulic Cutter 5/8” Capacity Operator’s Manual...
-
Page 2: Table Of Contents
CONTENTS Title Page Specifications General Information Troubleshooting Guide Operating Instructions Parts Diagram Parts List Warranty www.loosnaples.com Toll Free: 800-321-LOOS (5667) -
Page 3: Specifications
SPECIFICATIONS FEATURES • Lightweight and Portable • Works in Any Position • 180° Rotational Head • HC-16PL is Nickel Plated for Underwater Use SPECIFICATIONS Output: 4.4 ton Weight: 6 lbs. Size: 15”L Jaw Opening: .6” CAPACITIES Wire Ropes: 16 mm, 5/8” Soft Steel Bolts: 16 mm, 5/8”... -
Page 4: General Information
GENERAL INFORMATION GUIDE The following steps are guidelines for safe operation of the cutters. Please take the time to review them as these are helpful hints that have been accumulated over the years. 1. Stay within the maximum cutting limits of each tool as listed. 2. - Page 5 GENERAL INFORMATION GUIDE 6. There may be a residue of oil present on new tools when they are removed from the original shipping container. This is to protect the tool from corrosion during shipment and storage, and should not be considered defective. The tool can be cleaned with a spray degreaser or soapy water.
- Page 6 GENERAL INFORMATION GUIDE Always cut the material at a 90° angle to the blade. Any other angle may cause the blade and head shear to fracture. See illustration below. BLADE SHARPENING INSTRUCTIONS www.loosnaples.com Toll Free: 800-321-LOOS (5667)
-
Page 7: Troubleshooting Guide
TROUBLESHOOTING GUIDE 1. Problem: Small wire strands or pieces of cable or debris get jammed between the cutter head and blade, not allowing the blade to retract. Solution: A) Hold release lever down while tapping on the ram with a block of wood and a hammer. If this does not work or tool continues to hang up, proceed to step “B”. - Page 8 TROUBLESHOOTING GUIDE 3. Problem: Tool will not advance when handle is pumped. Solution: A) Remove body handle and check oil reservoir for prop- er fluid level. The oil should be to the top of the reservoir when the cap is removed. Be sure the tool is fully retracted before removing cap.
-
Page 9: Operating Instructions
OPERATING INSTRUCTIONS 1. Before cutting, make sure the material being cut is within the proper cutting capacity of the tool being used. 2. Open cutter head by lifting latch or removing lock pin, depend- ing on the model being used. 3. -
Page 10: Parts Diagram
PARTS DIAGRAM www.loosnaples.com Toll Free: 800-321-LOOS (5667) -
Page 11: Parts List
PARTS LIST www.loosnaples.com Toll Free: 800-321-LOOS (5667) -
Page 12: Warranty
WARRANTY Huskie Tools products carry a warranty that makes us a leader in the tool industry. No other manufacturer dares to back its tools as we do. All Huskie REC-SERIES battery-operated products carry a 5-year warranty. The ECO-SERIES battery-operated products carry a 1-year warranty. - Page 13 WARRANTY (CONT.) Huskie reserves the right to determine all warranty claims. Huskie will not waranty tools containing parts or batteries not originally supplied by Huskie. Failure due to misuse, improper maintenance, misapplication, not following instructions or warnings, abuse or repairs attempted by anyone other than Huskie Tools, Inc.
- Page 14 WARRANTY (CONT.) Complete Support Services Our customers have direct access to us for training, service, and problem solving. As specialists in tools, we maintain a trained repair staff and a large stock of parts. This contrasts with many tool suppliers who carry tools as a sideline without offering support services.
- Page 16 901 Industrial Blvd • Naples, FL 34104 Tel: (239) 643-LOOS • Fax (239) 643-4558 E-mail: info@loosnaples.com • Website: www.loosnaples.com INST-19 Rev. 09/29/15...