Toro Z Master Professional 2000 Series Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. Z Master Professional 2000 Series
  6. Setup instructions

Toro Z Master Professional 2000 Series Setup Instructions

Hide thumbs Also See for Z Master Professional 2000 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Z Master
Model No. All Models
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
11
12
13
Note:
Determine the left and right sides of the machine from the normal operating position.
© 2021—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Professional 2000 Series Riding Mower
Description
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No. 2 lithium or molybdenum grease
(purchase separately)
No parts required
No parts required
Operator's Manual
Engine owner's manual (non-Toro
engines)
Operator training material
Key
Registration card
Register at www.Toro.com.
Form No. 3433-516 Rev B
Qty.
–
Remove the machine from the crate.
–
Add fuel to the machine.
–
Check the engine-oil level.
–
Service the hydraulic fluid.
–
Check the tire pressure.
–
Servicing the battery.
Raise the rollover protection system
–
(ROPS).
–
Check the grass deflector.
–
Remove the shipping cable ties.
1 tube
Check the machine for grease.
–
Check the mower adjustment.
Check the machine before delivery to
–
the customer (all machines).
1
1
Deliver the machine to the customer.
1
2
1
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Setup Instructions
Use
*3433-516*

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Z Master Professional 2000 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Toro Z Master Professional 2000 Series

Summary of Contents for Toro Z Master Professional 2000 Series

  • Page 1 Check the mower adjustment. Check the machine before delivery to – No parts required the customer (all machines). Operator's Manual Engine owner's manual (non-Toro engines) Deliver the machine to the customer. Operator training material Registration card Note: Determine the left and right sides of the machine from the normal operating position.

  • Page 2: Removing The Machine From The Crate

    If removing the machine from a metal crate, refer to This machine is shipped filled with hydraulic fluid in the Dealer/Distributor Portal for further information. the reservoirs. Check the expansion tank; if necessary, add Toro ® HYPR-OIL ™ 500 hydraulic fluid, as recommended in...

  • Page 3: Checking The Tire Pressure

    Checking the Tire Pressure No Parts Required Procedure Pressure: 13 psi (90 kPa) Note: Check the tire pressure before starting the machine. Refer to your Operator’s Manual for the g236732 Figure 2 correct tire type and procedure. 1. Ensure that the ground 3.
  • Page 4 snap into position when the holes align with the pins. Push on the roll bar and ensure that both pins are engaged (Figure Raising the Rollover Protection System (ROPS) No Parts Required Procedure Pull both knobs out and rotate them 90 degrees so that they are not engaged (Figure Raise the roll bar to the operating position and...
  • Page 5 Checking the Grass Deflector No Parts Required Procedure If there are plastic ties holding the grass deflector up, remove them and lower the deflector into place. g021181 WARNING Figure 4 An uncovered discharge opening could allow 1. Grass deflector 3. End of spring the machine to throw objects toward you or 2.

  • Page 6: Checking The Mower Adjustment

    Removing the Shipping Checking the Machine for Cable Ties Grease No Parts Required Parts needed for this procedure: No. 2 lithium or molybdenum grease (purchase 1 tube Procedure separately) Note: This procedure is for machines with a Procedure MyRide™ suspension system only. Before you use the machine, check the machine for CAUTION grease;...
  • Page 7 Checking the Machine Before Delivery to the Customer (All Machines) No Parts Required Procedure Before delivering the machine to the customer, ensure that you have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures.
  • Page 8 Delivering the Machine to the Customer Parts needed for this procedure: Operator's Manual Engine owner's manual (non-Toro engines) Operator training material Registration card Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished.
  • Page 9 Ensure that the customer receives the Operator's Manual, engine owner's manual (non-Toro engines), Setup Instructions, and operator training material. Ensure that the customer knows that the Parts Catalog is available at www.Toro.com. Assist the customer in loading the machine. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provide below and keep a copy of this page for dealer records.
  • Page 10 Notes:...
  • Page 11 Notes:...

This manual is also suitable for:

744917449277287744967449374490

Table of Contents