Related Manuals for Lasermet ULTRA LEDS-ULT-470
Summary of Contents for Lasermet ULTRA LEDS-ULT-470
- Page 1 LEDS Ultra Sign Instruction Manual LASERMET ULTRA LED SIGN INSTRUCTION MANUAL SINGLE AND DUAL ASPECT ILLUMINATED SIGN LEDS-ULT-470 and LEDS-ULT-790 00625-53-000 Issue 4.1 19 January 2021...
-
Page 2: Table Of Contents
LED Ultra Sign Instruction Manual LASERMET LED Ultra Sign Instruction Manual Contents Declaration of Conformity ....................3 Safety Warnings ........................4 Concept ..........................5 Installation .......................... 6 Wiring ..........................9 ‘Sign Good’ Indicators ....................11 Specifications ........................12 Warranty ........................... 12 Contact Details ........................ -
Page 3: Declaration Of Conformity
00864-00-000 High Reliability 00866-03-000 High Reliability Dimmable DECLARATION OF CONFORMITY This is to certify that the LED Ultra Signs designated by Lasermet Part Number LEDS- ULT-470 has been tested in accordance with the following directives and standards and found to comply. -
Page 4: Safety Warnings
LED Ultra Sign Instruction Manual Safety Warnings This device is intended to be used as part of a safety system which may be used to protect personnel and equipment from possible injury, damage, or loss. As such it must be installed and wired according to these instructions and tested by suitably qualified persons. -
Page 5: Concept
The message is almost invisible when the sign is switched off. The sign may be used on its own or in conjunction with Lasermet’s interlock systems. When the sign is used on its own, Lasermet offer a power supply and switch kit which enables easy installation and operation. -
Page 6: Installation
If there are two or more adjacent signs stacked vertically, Lasermet supply a joining strip which fills the gaps between the signs and gives a more professional appearance. When mounting two or more signs vertically, allow a 4mm gap between the signs for insertion of the joining strip. - Page 7 LED Ultra Sign Instruction Manual Lasermet also supply a range of shallow surface trays which can accommodate multiple signs arranged vertically. Each tray has a Ø20mm cable/conduit entry which must be located at the top. Additional holes may be cut if required. The trays allow convenient hook-on mounting and electrical connection to the signs.
- Page 8 LED Ultra Sign Instruction Manual Figure 3. Mounting Arrangement using 4-way Wall Tray 00625-53-000 Issue 4.1 19 January 2021 Page 8 of 13...
-
Page 9: Wiring
With two-way signs, either one driver or the other is powered to select the illumination colour and message. Figure 8 shows a simple scheme to do this with a switch. Suitable controls are available from Lasermet. A three-way terminal block is provided on the driver board. Two terminals are used for the supply connections. - Page 10 LED Ultra Sign Instruction Manual Figure 4. Terminal Identification Figure 5. Connections for dual drivers using two power supplies Figure 6. Connections for one-way dual drivers using one power supply 00625-53-000 Issue 4.1 19 January 2021 Page 10 of 13...
-
Page 11: 5.1 'Sign Good' Indicators
LED Ultra Sign Instruction Manual Figure 7. Connections when using external dimming control (Omit second driver connections if not fitted) Figure 8. Two-way Sign Control 5.1 ‘Sign Good’ Indicators Each driver board has an indicator which shows as a white spot at each end of the sign. One-way signs having one driver board will show a spot at one end only. -
Page 12: Specifications
(LEDS-ULT-470) (LEDS-ULT-790) Dimensions are approximate. Values given as ‘typical’ are average values measured across a number of samples and are not guaranteed. Lasermet reserve the right to alter any specification without prior notice. Warranty Lasermet provide a 12-month warranty for defects in materials and manufacture, from the date of installation or delivery. -
Page 13: Contact Details
LED Ultra Sign Instruction Manual Contact Details Lasermet provide a full range of laser interlock equipment including interlock switches, illuminated warning signs, laser shutters, entry keypads with built-in fail-safe override timer, door locks, external power supplies etc. which can be interconnected to provide a complete system. We also supply equipment and consultancy covering all aspects of laser safety.