Related Manuals for Micron M2T4249
Summary of Contents for Micron M2T4249
- Page 1 Digital Menu Board Wall Mount Installation Instructions M2T4249 M3T4249 www.microndisplaysolutions.com...
-
Page 2: Table Of Contents
Table of Contents Important Safety Instructions..........................3 Models and Specifications ..........................4 Package Contents .............................. 5 Step 1 – Using Two (2) Wide or Three (3) Wide Menu Board Mount Only ............6 Step 2A – Joining 2W and 3W Menu Board Mounts to make 4W or Greater Mount (42” & 43”) ....7 Step 2B –... -
Page 3: Important Safety Instructions
Tested and Evaluated to CSA Model Code SPE-1000, Clause 6.2.8. Testé et évalué selon le code de modèle CSA SPE-1000, article 6.2.8 Warning: Maximum hanging load 100 Kg for M2T4249 and 120 Kg for M3T4249. Attention: Charge maximale suspendue 100 Kg pour M2T4249 et 120 Kg pour M3T4249. -
Page 4: Models And Specifications
Models and Specifications Product M2T4249 M3T4249 Type 2 Wide Tilt Menu Board 3 Wide Tilt Menu Board Screen Sizes 42” to 49” Tilt 0 to 15 Degrees Vesa 200 to 400 Security Locks Included Weight Load 100 kg 120 kg... -
Page 5: Package Contents
Package Contents Description Model Picture 2T4249 Preassembled Mount 3T4249 Part A 2T4249 Joiner Rail Assembly 3T4249 Part JR 2T4249 Panel VESA Bracket 3T4249 Part B 2T4249 End Cap 3T4249 Part EC 2T4249 Hardware 3T4249 Part H 2T4249 Cable Tie Clamp 3T4249 Part CC 2T4249... -
Page 6: Step 1 - Using Two (2) Wide Or Three (3) Wide Menu Board Mount Only
Step 1 – Using 2 Wide or 3 Wide Menu Board Mount Only Instructions Diagrams Do Not Remove Zip Ties Holding Mount Yet!. For a two (2) wide mount proceed to Step Fig. 1A Do Not Remove Zip Ties Holding Mount Yet!. For a three (3) wide mount the left and right sections need to be... -
Page 7: Step 2A - Joining 2W And 3W Menu Board Mounts To Make 4W Or Greater Mount (42" & 43")
Step 2A – Joining 2W & 3W Mounts to make 4W or > (For 42” & 43”) Mount Type Instructions Diagrams For configurations requiring 4W or 6W. • Join a 2W+2W menu board mount by using Fig. 2A Joiner Bars removed from Joiner Rail Assemblies provided (Part JRS). -
Page 8: Step 2B - Joining 2W And 3W Menu Board Mounts To Make 5W Or Greater Mount (46"+)
Step 2B – Joining 2W & 3W Mounts to make a 4W or > (46”+) Mount Type Instructions Diagrams For configurations requiring 4 wide or 6 wide menu boards. • Join a 2W+2W menu Fig. 2A board mount using the four (4) Joiner Rail Assemblies provided (Part JRS). -
Page 9: Step 3 -Fastening Temporary Wall Brackets To Wall
Step 3 –Fastening Temporary Wall Brackets to Wall Instructions Diagrams a) Determine center point for menu board on wall. See figure 3A. 1. Mark wall with centre point 2. Mark wall with outside measurements for menu board. 3. Determine location of wall studs. Note: Minimum of three (3) studs must be used to fasten mount to safely support weight of mount and screens... -
Page 10: Step 4 - Mounting To Wall
Step 4 – Mounting to Wall Instructions Diagrams • Lift mount and place so top wall rails are seated as shown in figure 4A. • This will allow mount to stay on wall temporarily to allow for easy marking and pre drilling into wall for fastening screws. -
Page 11: Step 5 -Tilt Mechanism Adjustment
Step 5 –Tilt Mechanism Adjustment Instructions Diagrams For a 2 wide mount there is a tilt adjustment mechanism at each end. For a 3 wide mount there are four (4) tilt adjustment mechanisms. The maximum tilt angle is 15 Degrees. Tilt safety screw. -
Page 12: Step 7 -Attaching Vesa Panel Brackets & Mounting Panels
Step 7 –Attaching VESA Panel Brackets & Mounting Panels Instructions Diagrams • Remove video display panels to be installed from their cartons and attach the Panel VESA Brackets (Part B) to back of video panels at the VESA mounts as shown in figure 7A. Mounting hardware is provided (Part •... -
Page 13: Step 8 - Installing Monitor Security Locks (Optional Item)
Step 8 – Installing Monitor Security Locks (Optional Item) Instructions Diagrams The Monitor Security Locks (Part SL) are used to secure monitor to Top Rail. • Place one (1) Monitor Security Lock on either the left or right Top Panel Clamp for each monitor. -
Page 14: Warranty
Micron Display Solutions (“MICRON”) warrants to the first purchaser for this product (“Product”), when shipped in its original container and sold or distributed in Canada by Micron or by an authorized Micron dealer, and Product was not sold “as is” or “sales final” that the Product will be free from defects in material and workmanship for a period of three (3) years and will within the warranty period, either repair the defective Product or provide the purchaser a replacement of the defective Product.
Need help?
Do you have a question about the M2T4249 and is the answer not in the manual?
Questions and answers