Acer Ferrari One 200 Service Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Laptop
  5. Ferrari One 200
  6. Service manual

Acer Ferrari One 200 Service Manual

Hide thumbs Also See for Ferrari One 200:
Table of Contents

Advertisement

Quick Links

See also: Quick Manual
Ferrari one Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to
http://csd.acer.com.tw

Advertisement

Table of Contents
loading

Related Manuals for Acer Ferrari One 200

Summary of Contents for Acer Ferrari One 200

  • Page 1 Ferrari one Series Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.tw...
  • Page 2 PRINTED IN TAIWAN...
  • Page 3 Revision History Please refer to the table below for the updates made on this service guide. Date Chapter Updates...
  • Page 4 Copyright Copyright © 2009 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
  • Page 5 Conventions The following conventions are used in this manual: SCREEN MESSAGES NOTE WARNING CAUTION IMPORTANT Denotes actual messages that appear on screen. Gives bits and pieces of additional information related to the current topic. Alerts you to any damage that might result from doing or not doing specific actions.
  • Page 6 DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

  • Page 7: Table Of Contents

    System Specifications Features ............1 System Block Diagram .
  • Page 8 Table of Contents Removing the Button Board ........62 Removing the Bluetooth Module .
  • Page 9 HDD Not Operating Correctly ........136 USB Failure (Right up/down side) .
  • Page 10 Table of Contents...

  • Page 11: System Specifications

    Up to 2 GB of DDR2 800 MHz memory, upgradeable to 4 GB using two soDIMM modules Display and graphics • 16:9 aspect ratio • 11.6" high-brightness Acer CrystalBrite™ LCD • ATI Radeon™ HD 3200 Graphics Storage subsystem • 2.5" hard disk drive •...

  • Page 12: Privacy Control

    ENERGY STAR® Special keys and controls • 84-/85-/88-key keyboard • Touchpad pointing device I/O interface • Acer DynaVivid Graphics Dock™ connector • Multi-in-1 card reader (SD/MMC/MS/MS PRO/xD) • USB 2.0 port • External display (VGA) port • Headphones/speaker/line-out jack with S/PDIF support •...

  • Page 13: System Block Diagram

    System Block Diagram Chapter 1...

  • Page 14: Your Notebook Tour

    Your Notebook Tour This section provides an overview of the features and functions of the notebook. Front View Icon Item Acer Crystal Eye Web camera for video communication. webcam Microphone Internal microphone for sound recording. Display screen Also called Liquid-Crystal Display (LCD), displays computer output (Configuration may vary by models).

  • Page 15: Closed Front View

    Icon Closed Front View Icon Chapter 1 Item Touchpad Touch-sensitive pointing device which functions like a computer mouse. Click buttons (left The left and right buttons function like the left and and right) right mouse buttons. Communication Indicates the status of WLAN / 3G communication. indicator (only for certain models) Power...

  • Page 16: Left View

    Item External display Connects to a display device (e.g., external (VGA) port monitor, LCD projector). Acer DynaVivid Connects to an Acer DynaVivid Graphics Dock Graphics Dock device. connector Ventilation slots Enable the computer to stay cool, even after prolonged use.

  • Page 17: Base View

    Base View Icon Battery bay Battery lock Hard disk bay Memory compartment Ventilation slots and cooling fan Battery release latch Chapter 1 Kensington lock Connects to a Kensington-compatible computer security lock. Note: Wrap the computer security lock cable around an immovable object such as a table or handle of a locked drawer.

  • Page 18: Rear View

    Rear View Icon Battery Indicators The computer has several easy-to-read status indicators. The battery indicator is visible even when the computer cover is closed. Icon Function Bluetooth Wireless LAN 3G communication Num Lock Caps Lock Battery NOTE: 1. Charging: The battery light shows amber when the battery is charging. 2. Fully charged: The light shows green when in AC mode.

  • Page 19: Touchpad Basics

    Touchpad Basics The following items show you how to use the Touchpad: • Move your finger across the Touchpad (1) to move the cursor. • Press the left (2) and right (3) buttons located beneath the Touchpad to perform selection and execution functions.

  • Page 20: Using The Keyboard

    Using the Keyboard Your computer has a close-to-full-sized keyboard and an embedded numeric keypad, separate cursor, lock, function and special keys. Lock Keys and embedded numeric keypad The keyboard has three lock keys which you can toggle on and off. Lock key Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase.

  • Page 21: Windows Keys

    Windows Keys The keyboard has two keys that perform Windows-specific functions. Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu. It can also be used with other keys to provide a variety of functions: <...

  • Page 22: Hot Keys

    Hot Keys The computer employs hotkeys or key combinations to access most of the computer's controls like screen brightness and volume output. To activate hotkeys, press and hold the <Fn> key before pressing the other key in the hotkey combination. Hotkey Icon <Fn>...

  • Page 23: Special Keys

    Special Keys You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your keyboard. The Euro symbol Open a text editor or word processor. Hold <Alt Gr> and then press the <5> key at the upper-center of the keyboard. NOTE: Some fonts and software do not support the Euro symbol.

  • Page 24: Hardware Specifications And Configurations

    HT-Link: 16-bit link supporting; speeds up to 800MHz • TDP: 13 W Cache Package Tech Size Fan Speed (RPM) 5500 5000 4500 4000 RS780MN 528-Pin FCBGA Package (21 x 21 mm) +1.1V, +1.2V, +1.8V, +3V, +NB_CORE Specification Core Acer P/N Voltage SPL Spec (dBA) Specification Chapter 1...
  • Page 25 Item Features South Bridge Specifications Item Chipset Package Power Chapter 1 Specification • Supports the mobile and desktop Athlon 64/Athlon 64FX/ Athlon X2/AMD Sempron/AMD Turion 64 processors, including both AM2 and S1 socket CPUs. • Supports 16-bit up/down HyperTransport(HT) 3.0 interface up to 4.4GT/s.
  • Page 26 Item Features System Memory Item Memory Controller Memory size DIMM socket number Supports memory size per socket Supports maximum memory size Supports DIMM type Supports DIMM Speed Support DIMM voltage Support DIMM package Memory module combinations Video Specifications Item Chipset Specification •...
  • Page 27 Item Package Features Hard Disk Drive Interface Item Vendor & Hitachi Model Name HTS545050B9A Capacity (GB) Bytes per sector Data heads Drive Format Disks Spindle speed 5400 (RPM) Performance Specifications Buffer size Interface Internal transfer 3GB/s rate (Gbits/sec., maximum max) I/O data transfer rate (Mbytes/sec.
  • Page 28 Item Internal transfer rate (Mbits/sec, max) I/O data transfer rate (Mbytes/sec max) DC Power Requirements Voltage Item Vendor & Model Toshiba Name MK1655GSX Capacity (GB) Bytes per sector Data heads Drive Format Disks Spindle speed (RPM) Performance Specifications Buffer size Interface Internal transfer rate (Mbits/sec,...
  • Page 29 Item Active Area (mm) Display resolution (pixels) Pixel Pitch (mm) Typical White Luminance (cd/m also called Brightness Contrast Ratio Response Time (Optical Rise Time/Fall Time) msec Typical Power Consumption (watt) Weight (with inverter) Physical Size (mm) Normal Input Voltage Electrical Interface Viewing Angle (degree) Horizontal (Right) / (Left) Vertical (Upper) / (Lower)
  • Page 30 Item Features • Headphone-out with S/PDIF, and Microphone-In. • • WLP 3.10, and stricter performance requirements for future WLP • Two stereo DAC supports 16/20/24-bit PCM for two independent playback(multiple streaming). • recording. • • 88.2k/96k/192kHz rate. LAN Interface Item LAN Chipset Atheros AR8131L Package...
  • Page 31 Media Card Reader Item Chipset Features Compliance Power Package Camera Item Vendor and model Chicony CNF9016 Type 640 x 480 VGA (0.3M) size 1/6” CMOS Interface USB 2.0 high speed interface Optical aperture Focusing range 17.4cm ~ Infinity, focus on 40cm Dimensions (L x W x H 64.8±0.3 x 7.9±0.1 x 3.64+0.15/- 0.25mm...
  • Page 32 Wireless LAN Item Specification Model • • Protocol 802.11a/b/g Interface PCI-Express 3G Module Item 3G Model Technical Standard Interface Antenna Battery Item Vendor & model name Battery Type Pack capacity Number of battery cell Package configuration Normal voltage Charge voltage Specification Foxconn Wireless LAN Atheros HB95 1x1 BG (HM) Foxconn Wireless LAN Atheros HB93...

  • Page 33: System Utilities

    System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup.

  • Page 34: Information

    Information The Information screen displays a summary of your computer hardware information. Information Main C P U T y p e C P U T y p e C P U S p e e d C P U S p e e d H D D M o d e l N a m e : H D D M o d e l N a m e : H D D S e r i a l N u m b e r :...

  • Page 35: Main

    Main The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery. Information Main S y s t e m T i m e : S y s t e m T i m e : S y s t e m D a t e : S y s t e m D a t e : T o t a l M e m o r y :...

  • Page 36: Security

    Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use. Information S u p e r v i s o r P a s s w o r d I s : S u p e r v i s o r P a s s w o r d I s : U s e r P a s s w o r d I s : U s e r P a s s w o r d I s : H D D P a s s w o r d I s :...
  • Page 37 Setting a Password Follow these steps as you set the user or the supervisor password: Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears: C o n f i r m N e w P a s s w o r d Type a password in the “Enter New Password”...
  • Page 38 Changing a Password Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears. E n t e r C u r r e n t P a s s w o r d C o n f i r m N e w P a s s w o r d Type the current password in the Enter Current Password field and press Enter.

  • Page 39: Boot

    Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes various USB diskette drives and the onboard hard disk drive. 1 . I D E 0 : W D C W D 2 5 0 0 B E V T - 2 2 Z C T 0 Information Main B o o t p r i o r i t y o r d e r :...

  • Page 40: Exit

    Exit The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility. Information Main E x i t S a v i n g C h a n g e s E x i t S a v i n g C h a n g e s E x i t D i s c a r d i n g C h a n g e s E x i t D i s c a r d i n g C h a n g e s L o a d S e t u p D e f a u l t s...

  • Page 41: Bios Flash Utility

    BIOS Flash Utility The BIOS flash memory update is required for the following conditions: New versions of system programs • New features or options • Restore a BIOS when it becomes corrupted. • Chapter 2...

  • Page 42: Dos Flash Utility

    DOS Flash Utility Perform the following steps to use the DOS Flash Utility: Press F2 during boot to enter the Setup Menu. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move USB HDD to position 1.

  • Page 43: Winflash Utility

    WinFlash Utility Perform the following steps to use the WinFlash Utility: In Windows run ZH6_xxxx_win.exe where xxxx is the bios version. For example, ZH6_3102_win.exe When the process is complete, close all programs and applications and reboot the system. Chapter 2...

  • Page 44: Remove Hdd/Bios Password Utilities

    Remove HDD/BIOS Password Utilities This section provide you with removing HDD/BIOS method: Remove HDD Password: When the user keys in the wrong password three times, the system reports the following error code to user. To unlock the HDD password, perform the following steps: Press Enter to display the Select Item screen.

  • Page 45: Removing Bios Passwords

    Removing BIOS Passwords: If you key in the wrong Supervisor Password three times, System Disabled displays on the screen. See the image below. Make a note of the number displayed: 14452 in this instance. Boot up the system to a removable bootable drive containing DOS and open a DOS prompt. For instructions on changing boot priority see “Boot”...

  • Page 46: Miscellaneous Utilities

    Miscellaneous Utilities Using Boot Sequence Selector Boot Sequence Selector allows the boot order to be changes without accessing the BIOS. To use Boot Sequence Selector, perform the following steps: Enter into DOS. Execute BS.exe to display the usage screen. Select the desired boot sequence by entering the corresponding sequence, for example, enter BS2 to change the boot sequence to HDD|CD ROM|LAN|Floppy.
  • Page 47 Manufacturer (Type1, Offset04h): Acer Product Name (Type1, Offset05h): Aspire one xxxxx Serial Number (Type1, Offset07h): 01234567890123456789 UUID String (Type1, Offset08h): xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx Asset Tag (Type3, Offset04h): Acer Asstag Example 2: Write Product Name to EEPROM Input: dmitools /wp Acer Example 3: Write Serial Number to EEPROM...
  • Page 48 Chapter 2...

  • Page 49: Machine Disassembly And Replacement

    Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. Disassembly Requirements To disassemble the computer, you need the following tools: • Wrist grounding strap and conductive mat for preventing electrostatic discharge •...

  • Page 50: Disassembly Process

    Unplug the AC adapter and all power and signal cables from the system. Place the system on a flat, stable surface. Remove the battery pack. Disassembly Process The disassembly process is divided into the following sections: • External components disassembly •...

  • Page 51: External Modules Disassembly Flowchart

    External Modules Disassembly Flowchart Remove Screw List Step Screw HDD Module M3*3.5(silver) 3G Module M2*4 WLAN Module M2*5 Chapter 3 Turn off system and peripherals power Disconnect power and signal cables from system Remove Dummy Card Remove Battery Remove SIM Card Remove Lower Covers Remove...

  • Page 52: Removing The Battery Pack

    Removing the Battery Pack Turn the computer over. Slide the battery lock/unlock latch to the unlock position. Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the main unit (2). Chapter 3...

  • Page 53: Removing The Dummy Card

    Removing the Dummy Card Press the dummy card to allow it to spring out. Remove the dummy card. Removing the SIM Card See “Removing the Battery Pack” on page 42. Press the SIM card to allow it to spring out. Chapter 3...

  • Page 54: Removing The Hard Disk Drive Module

    Pull the SIM card out and store carefully. Removing the Hard Disk Drive Module See “Removing the Battery Pack” on page 42. Loosen the two (2) captive screws on the HDD Cover. Remove the HDD Cover from the inside edge. Chapter 3...
  • Page 55 Grasp the black tab. Lift up on the black tab to pull the HDD out but do not remove completely. Flip the HDD over to allow access to the HDD cable. CAUTION: Do not pul the HDD out before disconnecting the HDD cable. Grasp the HDD cable connector tab and pull up.

  • Page 56: Removing The 3G Module

    Remove the HDD cable from the HDD. Remove the four (4) screws of the HDD rails. Step HDD Disassembly 3*3.5 (silver) Remove the rails from the HDD. Removing the 3G Module See “Removing the Battery Pack” on page 42. Screw Quantity Screw Type.
  • Page 57 Loosen the three (3) captive screws in the Memory Cover. Lift the Memory Cover out from the rear edge. Remove the cables from the 3G module. Chapter 3...
  • Page 58 Remove the one (1) screw from the 3G module. Step 3G Disassembly Remove the 3G module. Screw Quantity Screw Type. Chapter 3...

  • Page 59: Removing The Dimm Module

    Removing the DIMM Module See “Removing the Battery Pack” on page 42. Loosen the three (3) captive screws in the Memory Cover. Remove the Memory Cover from the rear edge. Pull open the two memory side clips. Chapter 3...
  • Page 60 Lift the memory card out. Repeat steps 4) and 5) for the second memory card. Chapter 3...

  • Page 61: Removing The Wlan Module

    Removing the WLAN Module See “Removing the Battery Pack” on page 42. Loosen the two (2) captive screws in the HDD Cover. Remove the HDD Cover from the inside edge. Loosen the three (3) captive screws in the Memory Cover. Chapter 3...
  • Page 62 Remove the Memory Cover from the rear edge. Remove the cables on the WLAN module. Remove the one (1) screw on the WLAN module. Step WLAN Disassembly Screw Quantity Screw Type. Chapter 3...
  • Page 63 Remove the WLAN module. Chapter 3...

  • Page 64: Main Unit Disassembly Process

    Main Unit Disassembly Process IMPORTANT: Cable paths and positioning may not represent the actual model. During the removal and replacement of components, ensure all available cable channels and clips are used and that the cables are replaced in the same position. NOTE: The product previews seen in the disassembly procedures may not represent the final product color or configuration.
  • Page 65 Screw List Step Lower Cover Lower Cover Lower Cover Upper Cover 2.0*2.5 (silver) Upper Cover Upper Cover Button Board M2-0.4*2 IO Board Main Board LCD Hinge Speaker Module Chapter 3 Screw Quantity Part No. 86.S0207.001 86.TG607.004 86.FRC07.001 86.TG607.004 86.S0207.001 86.TG607.004 86.W4107.002 86.TPK07.001 86.S0207.001...

  • Page 66: Removing The Keyboard

    Removing the Keyboard IMPORTANT: The keyboard is easily warped or damaged during the removal process. Take care not to use excessive force when removing the keyboard and replace if any damage occurs. See “Removing the Battery Pack” on page 42. Press the four (4) latches.
  • Page 67 Flip the keyboard over. Unlock the keyboard cable. Remove the keyboard cable and keyboard. Chapter 3...

  • Page 68: Removing The Upper Cover

    Removing the Upper Cover See “Removing the Battery Pack” on page 42. See “Removing the SIM Card” on page 43. See “Removing the Hard Disk Drive Module” on page 44. See “Remove the rails from the HDD.” on page 46. See “Removing the DIMM Module”...
  • Page 69 Turn the computer over and remove the eleven (11) screws in the upper cover. Step Upper Cover 2.0*2.5 Silver Disassembly 10. Unlock the I/O board to main board cable at both ends. Chapter 3 Screw Quantity 1 (green call out) 1 (blue call out) 9 (red call out) Screw Type.
  • Page 70 11. Disconnect the I/O board to main board cable at both ends. 12. Unlock and disconnect the button board to main board cable. Chapter 3...
  • Page 71 13. Pry up the Upper Cover starting from the side and lift away. 14. Remove the I/O board to main board cable. Chapter 3...

  • Page 72: Removing The Button Board

    Removing the Button Board IMPORTANT: The Touchpad Board cannot be removed individually. To replace the Button Board, replace the entire Upper Cover. See “Removing the Upper Cover” on page 58. Unlock the touchpad cable at both ends. Remove the touchpad cable. Disconnect the button board cable from the button board.
  • Page 73 Pull the button board cable away from the adhesive. Remove the button board cable. Remove the two (2) screws of the button board. Step Button Board M2-0.4*2 Disassembly Chapter 3 Screw Quantity Screw Type.
  • Page 74 Lift the button board away. Chapter 3...

  • Page 75: Removing The Bluetooth Module

    Removing the Bluetooth Module See “Removing the Upper Cover” on page 58. Disconnect the Bluetooth module to main board cable. Pull the Bluetooth module away. Chapter 3...

  • Page 76: Removing The I/O Board

    Removing the I/O Board See “Removing the Upper Cover” on page 58. Open the locking latch at both ends of the card reader cable connectors. Remove the card reader cable. Disconnect the DC power cable connector from the mainboard. Chapter 3...
  • Page 77 Remove the tape and lift the DC cable out of the cable guide. Disconnect the DC power cable from the I/O board. Remove the one (1) screw in the I/O board. Step IO Board Disassembly Chapter 3 Screw Quantity Screw Type.
  • Page 78 Lift the I/O board up by the inner edge and pull away on the angle. Chapter 3...

  • Page 79: Removing The Lcd Module

    Removing the LCD Module See “Removing the Upper Cover” on page 58. See “Removing the I/O Board” on page 66. Lift up the LCD cable protective over. Disconnect the LCD cable connector. Chapter 3...
  • Page 80 Remove the two (2) screws from the left and right hinges of the LCD module. Step LCD Disassembly Lift away the LCD module and lay it down. NOTE: Lay the LCD down on a clear smooth surface to prevent damage. Pull the antenna cables free of the chassis, threading the antenna cables through from the bottom side..

  • Page 81: Removing The Mainboard

    Removing the Mainboard See “Removing the Upper Cover” on page 58. See “Removing the Bluetooth Module” on page 65. See “Removing the I/O Board” on page 66. See “Removing the LCD Module” on page 69. Disconnect the speaker connector. Remove the one (1) screw in the main board. Step Main Board Disassembly...
  • Page 82 Lift out the main board from the inside edge. Chapter 3...

  • Page 83: Removing The Thermal Module

    Removing the Thermal Module See “Removing the Mainboard” on page 71. Disconnect fan connector. Remove the three (3) screws (red call outs) and loosen the two (2) captive screws (blue call outs). Step Thermal Module Disassembly Chapter 3 Screw Quantity Screw Type.
  • Page 84 Lift the fan away from the main board. Chapter 3...

  • Page 85: Removing The Cpu

    Removing the CPU See “Removing the Thermal Module” on page 73. Using a flat head screwdriver to turn the CPU mounting lock to the OFF position. Locked CPU Lift the CPU out and store carefully. WARNING:Do not touch the thermal grease to prevent bodily harm. Removing the RTC Battery.
  • Page 86 Lift the RTC battery out of its holder. Chapter 3...

  • Page 87: Removing The Speaker Modules

    Removing the Speaker Modules See “Removing the Mainboard” on page 71. Remove the three (3) screws securing the Speakers to the lower cover. Step Speaker Module Disassembly Remove the tape from the speaker cable. Chapter 3 Screw Quantity Screw Type.
  • Page 88 Lift the speaker module out of the lower cover. Chapter 3...

  • Page 89: Lcd Module Disassembly Process

    LCD Module Disassembly Process IMPORTANT: Cable paths and positioning may not represent the actual model. During the removal and replacement of components, ensure all available cable channels and clips are used and that the cables are replaced in the same position. NOTE: The product previews seen in the disassembly procedures may not represent the final product color or configuration.
  • Page 90 Step Screw Quantity Part No. LCD Bracket 2*2.5 86.TPK07.001 Disassembly Chapter 3...

  • Page 91: Removing The Lcd Bezel

    Removing the LCD Bezel See “Removing the LCD Module” on page 69. Remove the two (2) screw covers. Remove the two (2) screws. Step Bezel Disassembly Chapter 3 Screw Quantity Screw Type.
  • Page 92 Pry the bezel free at the corner and lift the bezel off the hinge. Pry the bezel free around the panel. iii) Chapter 3...

  • Page 93: Removing The Camera Board

    Removing the Camera Board See “Removing the LCD Bezel” on page 81. Disconnect the camera board connector Lift the camera board out. Chapter 3...

  • Page 94: Removing The Lcd Panel

    Removing the LCD Panel See “Removing the Camera Board” on page 83. Lift the microphone off the adhesive. Remove the four (4) screws. Step LCD Panel Disassembly Screw Quantity Screw Type. Chapter 3...
  • Page 95 Lift the LCD panel out of the LCD module. Chapter 3...

  • Page 96: Removing The Lcd Brackets

    Removing the LCD Brackets See “Removing the LCD Panel” on page 84. Pick up the panel and remove the four (4) screws holding the brackets in place. Step LCD Panel Brackets 2*2.5 (silver) Disassembly Screw Quantity Screw Type. Chapter 3...

  • Page 97: Removing The Fpc Cable

    Removing the FPC Cable See “Removing the LCD Panel” on page 84. Pull the vertical foil strip off the microphone cable. Pull off the horizontal foil strip till the FPC cable is completely exposed. Pull the cable sleeve off the adhesive. Chapter 3...
  • Page 98 Lift up the clear connector protector. Disconnect the connector. Pull the microphone cable free of the adhesive. Chapter 3...

  • Page 99: Removing The Antennas

    Removing the Antennas See “Removing the LCD Panel” on page 84. Lift up the four (4) foil tabs on each corner. Pull the wiring free of the retention guides. Chapter 3...
  • Page 100 Remove the magnet. Pull the foil and antennas off the adhesive Chapter 3...

  • Page 101: Lcd Reassembly Procedure

    LCD Reassembly Procedure Replacing the Antennas Adhere the Right Antenna Pad (yellow and blue cable) to the LCD cover. Adhere the Left Antenna Pad (white and blue cable) to the LCD Cover. Insert the antenna cables into the retention guides around the top left corner of the LCD cover and then mount the magnet.
  • Page 102 Insert the antenna cables into the retention guides around both sides. Flatten the four (4) foil tabs on each corner. Chapter 3...

  • Page 103: Replacing The Fpc Cable

    Replacing the FPC Cable Pull back the foil from the panel and lay the FPC cable on the panel Apply adhesive and press down the FPC cable microphone extension. CAUTION: Ensure that the microphone is properly aligned with the top of the panel. Connect the FPC cable connector.
  • Page 104 Press down the clear FPC connector protective cover. Apply adhesive and press down the FPC cable sleeve. Press the foil back down on top of the FPC cable. Chapter 3...

  • Page 105: Replacing The Lcd Brackets

    Replacing the LCD Brackets Replace the four (4) screws in the left and right brackets. Step LCD Bracket Assembly 2*2.5 (silver) Replacing the LCD Panel Place the LCD panel on the cover. Chapter 3 Screw Quantity Screw Type.
  • Page 106 Replace the four (4) screws. Step LCD Panel Disassembly Apply adhesive and press the microphone into place. Screw Quantity Screw Type. Chapter 3...

  • Page 107: Replacing The Camera Board

    Replacing the Camera Board Place the camera onto the LCD cover. Connect the cable to the Camera Board Replacing the LCD Bezel Place the bezel hinge cover over the hinges and ensure the wiring is correctly routed under the center hinge pin.
  • Page 108 Press the bezel down around the edges. Chapter 3...
  • Page 109 Replace the two (2) screws. Step LCD Bezel Assembly Replace the two screw covers. Chapter 3 Screw Quantity Screw Type.

  • Page 110: Main Unit Reassembly Process

    Main Unit Reassembly Process Replacing the Speaker Module Place the speaker module onto the lower cover. Replace the three (3) screws Step Speaker Module Assembly Screw Quantity Screw Type. Chapter 3...

  • Page 111: Replacing The Rtc Battery

    Lay the cable into the retention guides and press down the adhesive tape. Replacing the RTC battery Insert the RTC battery into the holding clips. Replacing the CPU Place the CPU into the socket paying attention to the correct alignment of the locating triangle in the corner.

  • Page 112: Replacing The Thermal Module

    Turn the CPU lock to the locked position. Replacing the Thermal Module IMPORTANT: Ensure all heat pads are in place before replacing the Thermal Module. The following TIM material and dimensions (mm) are approved for use: CPU TIM PSX-D 18.3*12.3mm Vram TIM T-Flex-320 13*9*05mm Remove all traces of thermal grease or pad adhesive from the CPU and thermal module using a lint-free cloth or cotton swab and Isopropyl Alcohol, Acetone, or other approved cleaning agent.
  • Page 113 Place the thermal module on the main board. Tighten the two (2) captive screws (blue call outs) and replace the three (3) screws (red call outs) of the thermal module. Step Thermal Module Assembly Connect the fan cable to the main board. Chapter 3 Screw Quantity...

  • Page 114: Replacing The Mainboard

    Replacing the Mainboard Place the main board into the lower cover on an angle first aligning the I/0 ports. Replace the one (1) screw. Step Main Board Assembly Connect the speaker connector. Screw Quantity Screw Type. Chapter 3...

  • Page 115: Replacing The Lcd Module

    Replacing the LCD Module Thread the antenna cables through to the bottom side of the lower cover and place in the retention guides. Place the hinges down on the lower case and ensure correct positioning of the antenna cables and the LCD cable and replace the two (2) screws.

  • Page 116: Replacing The I/O Board

    Replace the LCD cable connector. Press down the LCD cable connector protective cover. Replacing the I/O Board Place the I/O board into the lower cover on an angle first aligning the I/O ports. Chapter 3...
  • Page 117 IMPORTANT:Ensure that the WLAN/3G switch and the Bluetooth switch are properly aligned in the plastic slide switch covers in the lower cover. NOTE: You will feel the spring tension in the lower case sliders when the switches have been properly engaged.
  • Page 118 Reconnect the DC cable to the I/O board. Lay the DC cable into the retention guide and press down the adhesive tape. Reconnect the DC cable to the main board. Chapter 3...

  • Page 119: Replacing The Bluetooth Module

    Reconnect the card reader cable. Replacing the Bluetooth Module Place the Bluetooth module into position ensuring the board fits into the slot in the speaker module. Chapter 3...

  • Page 120: Replacing The Button Board

    Reconnect the Bluetooth cable. Replacing the Button Board Place the button board on the upper cover. Chapter 3...
  • Page 121 Replace the two (2) screws. Step Button Board 2-0.4*2 Assembly Insert the button board cable into the upper cover. Apply adhesive and press the button board cable down. Chapter 3 Screw Quantity Screw Type.
  • Page 122 Connect the button board cable to the button board. Connect the touch pad cable to the touch pad and the button board. Chapter 3...

  • Page 123: Replacing The Upper Cover

    Replacing the Upper Cover Insert the IO cable into the upper cover. Place the upper cover onto the lower cover first aligning the hinges Chapter 3...
  • Page 124 Press around the edges of the upper cover. Connect the button board cable to the main board. Chapter 3...
  • Page 125 Connect the IO cable to the IO card and main board. Chapter 3...
  • Page 126 Replace the eleven (11) screws in the upper cover. Step Upper Cover Assembly 2.0*2.5 silver Replace the ten (10) screws in the lower cover. Step Lower Cover Assembly Screw Quantity 1 (green call out) 1 (blue call out) 9 (red call out) Screw Quantity 4 (red call out)

  • Page 127: Replacing The Keyboard

    Replacing the Keyboard Connect the keyboard cable into the mainboard. Turn the keyboard over and press the keyboard into place Replacing the WLAN Module Insert the WLAN module. Chapter 3...

  • Page 128: Replacing The Dimm Module

    Replace the one (1) screw. Step WLAN Assembly Replace the two cables (white is MAIN, black AUX) Replacing the DIMM Module Insert the DIMM module. Screw Quantity Screw Type. Chapter 3...

  • Page 129: Replacing The 3G Module

    Press the DIMM module down. Replacing the 3G Module Insert the 3G module. Chapter 3...
  • Page 130 Replace the one (1) screw. Step 3G Board Assembly Lay the 3G antenna cables into the retention guides. Connect the antenna cables (blue cable is MAIN, yellow cable is AUX). Screw Quantity Screw Type. Chapter 3...

  • Page 131: Replacing The Hdd Module

    Replacing the HDD Module Attach the rails and replace the four (4) screws in the HDD rails. Step HDD Assembly 3.0*3.5 (silver) Connect the HDD cable to the HDD. Chapter 3 Screw Quantity Screw Type.

  • Page 132: Replacing The Lower Covers

    Connect the HDD cable to the main board. Lift up the black tab and place the HDD into the bay. Replacing the Lower Covers Replace the memory cover aligning the front tabs first. Chapter 3...
  • Page 133 Tighten the three (3) captive screws. Replace the HDD cover, aligning the outside edge tabs first. Tighten the two (2) captive screws. Chapter 3...

  • Page 134: Replacing The Sim Card

    Replacing the SIM Card Insert the SIM card until it clicks into place. Replacing the Battery Insert the battery. Slide the battery lock switch into the closed position. Chapter 3...

  • Page 135: Replacing The Dummy Card

    Replacing the Dummy Card Insert the dummy card until it clicks into place. Chapter 3...
  • Page 136 Chapter 3...

  • Page 137: Troubleshooting

    Common Problems Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. Obtain the failing symptoms in as much detail as possible.

  • Page 138: Power On Issue

    Power On Issue If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not replace non-defective FRUs: Start Start Start Check Check AC/Battery AC/Battery Power on Power on Check Check Daughter/B & Daughter/B &...

  • Page 139: No Display Issue

    No Display Issue If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace non-defective FRUs: Replace LCD LCD Module OK? Panel and Cable No POST or Video If the POST or video doesn’t display, perform the following actions one at a time to correct the problem. Make sure that the internal display is selected.

  • Page 140: Random Loss Of Bios Settings

    Disconnect power and all external devices including port replicators or docking stations. Remove any memory cards and CD/DVD discs. Restart the computer. If the computer boots correctly, add the devices one by one until the failure point is discovered. Reseat the memory modules. Remove the drives (see “Disassembly Process”...

  • Page 141: Lcd Failure

    If HDD information is missing from the BIOS, the drive may be defective and should be replaced. Replace the Motherboard. If the Issue is still not resolved, see “Online Support Information” on page 165. LCD Failure If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace non- defective FRUs: Start Start...

  • Page 142: Built-In Keyboard Failure

    Built-In Keyboard Failure If the built-in Keyboard fails, perform the following actions one at a time to correct the problem. Do not replace non-defective FRUs: Start Keyboard properly connected? Keyboard functioning? Replace mainboard Disconnect and reconnect Replace Keyboard Chapter 4...

  • Page 143: Touchpad Failure

    Touchpad Failure If the Touchpad doesn’t work, perform the following actions one at a time to correct the problem. Do not replace non-defective FRUs: Start Start Check M/B T/P Check M/B T/P Check Check TouchPad TouchPad Swap M/B Swap M/B Chapter 4 Re-assemble the Re-assemble the...

  • Page 144: Internal Speaker Failure

    Internal Speaker Failure If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace non-defective FRUs: Start Start Check M/B SPK Check M/B SPK cable cable Check Logic Check Logic Upper/Logic Upper/Logic upper upper...

  • Page 145: Internal Microphone Failure

    Ensure that all volume controls are set mid range: Click the volume icon on the taskbar and drag the slider to 50. Ensure that the volume is not muted. Click Mixer to verify that other audio applications are set to 50 and not muted. Navigate to Start Control Panel as the default audio device (green check mark).

  • Page 146: Hdd Not Operating Correctly

    Check that the microphone is enabled. Navigate to Start Sound and select the Recording tab. Right-click on the Recording tab and select Show Disabled Devices (clear by default). The microphone appears on the Recording tab. Right-click on the microphone and select Enable. Select the microphone then click Properties.

  • Page 147: Usb Failure (Right Up/Down Side)

    USB Failure (Right up/down side) If the rightside USB port fails, perform the following actions one at a time to correct the problem. Do not replace non-defective FRUs: Start Start Check USB/B to Check USB/B to M/B cable M/B cable Check USB/B Check USB/B Swap M/B...

  • Page 148: Intermittent Problems

    Issue” on page 128.): Power-off the computer. Visually check them for damage. If any problems are found, replace the FRU. Remove or disconnect all of the following devices: • Non-Acer devices • Printer, mouse, and other external devices • Battery pack •...

  • Page 149: Post Code Reference Tables

    POST Code Reference Tables These tables describe the POST codes and components of the POST process. Code Beeps 1-2-2-3 1-3-1-1 1-3-1-3 1-3-4-1 1-3-4-3 1-4-1-1 Chapter 4 POST Routine Description Verify Real Mode Disable Non-Maskable Interrupt (NMI) Get CPU type Initialize system hardware Initialize chipset with initial POST values Set IN POST flag Initialize CPU registers...
  • Page 150 Code Beeps 2-1-2-3 2-2-3-1 POST Routine Description POST device initialization Check ROM copyright notice Check video configuration against CMOS Initialize PCI bus and devices Initialize all video adapters in system QuietBoot start (optional) Shadow video BIOS ROM Display BIOS copyright notice Display CPU type and speed Initialize EISA board Test keyboard...
  • Page 151 Code Beeps Chapter 4 POST Routine Description Initialize Extended BIOS Data Area Test and initialize PS/2 mouse Initialize floppy controller Determine number of ATA drives (optional) Initialize hard-disk controllers Initialize local-bus hard-disk controllers Jump to UserPatch2 Build MPTABLE for multi-processor boards Install CD ROM for boot Clear huge ES segment register Fixup Multi Processor table...
  • Page 152 Code Beeps Code Beeps POST Routine Description PnPnd dual CMOS (optional) Initialize notebook docking (optional) Initialize notebook docking late Force check (optional) Extended checksum (optional) Unknown interrupt For Boot Block in Flash ROM Initialize the chipset Initialize the bridge Initialize the CPU Initialize system timer Initialize system I/O Check force recovery boot...

  • Page 153: Jumper And Connector Locations

    Jumper and Connector Locations Mainboard Top View Item Description LVD Connector JSIMI SIM Card DC In Lan Connector Bluetooth Connector USB & Card Reader Connector Speaker Connector Chapter 5 Item Description ALC272 Clock Generator Touch Pad Connector Keyboard Connector SB710 Keyboard controller Chapter 5...

  • Page 154: Mainboard Bottom View

    Mainboard Bottom View Item CN15 Fan Connector CN16 Lasso CN18 Battery Connector CN12 3G Card CN10 HDD Connector Description Item CN11 CN13 CN14 CN17 Description WIFI Card DRII Socket DRII Socket CPU Socket RS780MN Side Port Memory Chapter 5...

  • Page 155: Bios Recovery

    BIOS Recovery BIOS Recovery by Crisis Disk BIOS Recovery Boot Block The BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to the factory settings if a BIOS flash process fails.
  • Page 156 Chapter 5...

  • Page 157: Fru (Field Replaceable Unit) List

    Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

  • Page 158: California Exploded Diagrams

    1. Keyboard 2. Upper Cover 3. TP board 4. IO Cable 5. Mainboard 6. Thermal Cable 7. Thermal Module 8. Memory Module Acer PN Item KB.I110A.085 11. Bluetooth Module 60.FRC07.001 12. DC Power Cable 55.FRC07.002 13. I/O Board 14. 3G Module MB.FRB06.001...

  • Page 159: Lcd Assembly

    Item 9. Lower Cover 10. Memory Cover LCD Assembly Item 1. LCD Bezel 2. LCD Panel Chapter 6 Acer PN Item 60.FRB07.001 19. HDD Door 42.FRC07.002 Acer PN Item 60.FRC07.007 5. Antennas w/cable LK.11605.003 6. Camera module Acer PN 42.FRC07.001 Acer PN LZ.23500.006...
  • Page 160 Item 3. LeftHinge 4.LCD FCP w/microphone Acer PN Item 33.FRC07.002 7. Right hinge 50.FRC07.004 8. LCD Module Case Acer PN 33.FRC07.001 60.FRB07.003 Chapter 6...

  • Page 161: California Fru Listv

    California FRU ListV CATEGORY ADAPTER ADAPTER DELTA 30W 19V 1.7X5.5X11 BLACK ADP-30JH BA LF ADAPTER LITE-ON 30W 1.7X5.5X11 BLACK PA-1300- 04AC LF ADAPTER HIPRO 30W 19V 1.7X5.5X11 BLACK HP- A0301R3 B1LF LF Adapter DELTA 65W 19V 1.7x5.5x11 Yellow ADP-65JH DB A, LV5 LED LF Adapter LITE-ON 65W 19V 1.7x5.5x11 Yellow PA-1650- 22AC LV5 LED LF...
  • Page 162 CATEGORY PWR CORD V943B30001218008 DANISH 3P PWR CORD(ISR)1.8M 3PBLK FZ0I0008-038 PWR CORD V50CB3T3012180QD TW-110V,3P POWER CORD(SWI)1.8M 3PBLACK FZ010008-011 POWER CORD(IT) 1.8M 3PBLACK FZ010008-008 POWER CORD(S.A) 1.8M 3BLACK FZ010008-006 POWER CORD US 3PIN ROHS POWER CORD(EU) 1.8M 3PBLACK FM010008-010 POWER CORD(UK) 1.8M 3PBLACK FP010008-013 POWER CORD BRAZIL IMETRO 3 PIN POWER CORD UK 3PIN BLUETOOTH CABLE...
  • Page 163 CATEGORY LCD COVER ASSY UV RED W/3G ANTENNA LCD COVER ASSY IMR RED W/3G ANTENNA LCD COVER ASSY UV RED W/WF ANTENNA LCD COVER ASSY IMR RED W/WF ANTENNA LCD BEZEL ASSY - BLACK HDD COVER - BLACK RAM COVER - BLACK HINGE - R HINGE - L SD DUMMY CARD...
  • Page 164 CATEGORY HDD TOSHIBA 2.5" 5400rpm 160GB MK1655GSX Libra SATA LF F/W: FG011J HDD HGST 2.5" 5400rpm 160GB HTS545016B9A300 Panther B SATA LF F/W:C60F Disk imbalance criteria = 0.014g-cm HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO ML160 SATA LF F/W:11.01A11 HDD SEAGATE 2.5" 5400rpm 250GB ST9250315AS Wyatt SATA LF F/W:0001SDM1 HDD TOSHIBA 2.5"...
  • Page 165 Keyboard ACER NT1T Ferrari California 85KS Black Italian Texture Keyboard ACER NT1T Ferrari California 88KS Black Japanese Texture Keyboard ACER NT1T Ferrari California 85KS Black US w/ Canadian French Texture Keyboard ACER NT1T Ferrari California 85KS Black Danish Texture Keyboard ACER NT1T Ferrari California 85KS Black Nordic...
  • Page 166 CATEGORY Keyboard ACER NT1T Ferrari California 84KS Black US International w/ Hebrew Tex Keyboard ACER NT1T Ferrari California 85KS Black Norwegian Texture Keyboard ACER NT1T Ferrari California 84KS Black Korean Texture Keyboard ACER NT1T Ferrari California 84KS Black Chinese Texture LED LCD AUO 11.6"...
  • Page 167 CATEGORY THERMAL MODULE SPEAKER SPEAKER MODULE ASSY(WITH L/R) MISCELLANEOUS LCD BEZEL RUBBER UPPER CASE RUBBER FRONT LENS RUBBER LOWER CASE RUBBER FOOT - BACK LOWER CASE RUBBER FOOT - FRONT SCREW SCREW M2*5-I(BZN)(NYLOK) SCREW M2.0*3.0-I,IRON SP SCREW M2-0.4*2-I(BNI)(NYLOK)(7,0.6)IRON SCREW M2.0*8.0-I(BZN)(NYLOK) SCREW M2.0*2.5-I(BUWZN) SCREW M3*0.5+3.5I SCREW 2.0*4.0...
  • Page 168 Chapter 6...
  • Page 169 314G25n FO200- EMEA Holland 313G25n FO200- EMEA Italy 312G25n FO200- EMEA Russia 312G25i Appendix A Acer Part No LX.FRC02.138 FO200-312G25n W7HP64FRGR1 MC UMACrk 1*2G/250/6L2.8/5R/ CB_bgn_0.3D_AU_EL32 LX.FRC02.078 FO200-313G25n W7HP64FRHU1 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_AU_HU12 LX.FRC02.151 FO200-312G25n W7HP64FRHK2 MC UMACrk 2*1G/250/BT/6L2.8/5R/ CB_bgn_0.3D_AU_ZH35 LX.FRC02.080 FO200-313G25n W7HP64FRPT1 MC UMACrk 2G+1G/250/6L2.2/5R/...
  • Page 170 314G50n FO200- EMEA Denmark 313G32n FO200- EMEA Greece 312G25n FO200- EMEA Israel 312G25n FO200- EMEA Italy 312G25n Country Acer Part No LX.FRC02.065 LX.FRC02.150 LX.FRC02.149 LX.FRC02.148 LX.FRC02.147 LX.FRC02.123 LX.FRC01.002 LX.FRC02.124 LX.FRC02.146 LX.FRC02.103 LX.FRC02.076 LX.FRC02.129 LX.FRC02.130 LX.FRC02.144 LX.FRC02.143 LX.FRC02.142 Description FO200-313G25n W7HP64FRDK2 MC UMACrk 2G+1G/250/6L2.2/5R/...
  • Page 171 314G50n FO200- EMEA Norway 314G50n FO200- EMEA Denmark 313G32n FO200- EMEA 312G25n FO200- EMEA Middle East 312G25n Appendix A Country Acer Part No LX.FRC02.141 LX.FRC02.140 LX.FRC02.139 LX.FRC02.136 LX.FRC02.135 LX.FRC02.134 LX.FRC02.102 LX.FRC02.128 LX.FRC02.133 LX.FRC02.132 LX.FRC02.131 S2.FRC02.004 LX.FRC02.127 LX.FRC02.126 LX.FRC02.125 LX.FRC02.005 LX.FRC02.003...
  • Page 172 Austria 313G25n FO200- EMEA Germany 313G25n FO200- EMEA Israel 313G25n FO200- EMEA Israel 313G25n FO200- EMEA Poland 313G25n Country Acer Part No LX.FRC02.098 LX.FRC01.001 LX.FRC02.122 LX.FRC02.121 LX.FRC02.120 LX.FRC02.118 LX.FRC02.117 LX.FRC02.116 LX.FRC02.114 LX.FRC02.113 LX.FRC02.112 LX.FRC02.101 LX.FRC02.072 LX.FRC02.012 LX.FRC02.085 LX.FRC02.084 LX.FRC02.087 Description FO200-313G25n W7HP64EMFRME2 MC UMACrk 2G+1G/250/6L2.2/5R/...
  • Page 173 313G25n FO200- EMEA 313G25n FO200- EMEA Greece 313G25n FO200- EMEA Switzerland 313G25n FO200- EMEA Cyprus 313G25n Appendix A Country Acer Part No LX.FRC02.091 LX.FRC02.095 LX.FRC02.074 LX.FRC02.086 LX.FRC02.093 LX.FRC02.094 LX.FRC02.073 LX.FRC02.077 LX.FRC02.066 LX.FRC02.079 LX.FRC02.104 LX.FRC02.075 LX.FRC02.096 LX.FRC02.001 LX.FRC02.083 LX.FRC02.088 LX.FRC02.082 Description FO200-313G25n W7HP64EMFRZA2 MC UMACrk 2G+1G/250/6L2.2/5R/...
  • Page 174 Zealand FO200- Singapore 312G25n FO200- Australia/ 314G50n Zealand FO200- Singapore 314G32n FO200- Singapore 312G32n FO200- CHINA China 314G50n Country Acer Part No LX.FRC02.089 LX.FRC02.092 LX.FRC02.099 LX.FRC02.090 LX.FRC02.097 LX.FRC02.081 LX.FRC02.067 LX.FRC02.071 LX.FRC02.070 LX.FRC02.111 LX.FRC02.110 LX.FRC02.109 LX.FRC02.108 LX.FRC02.107 LX.FRC02.106 LX.FRC02.105 LX.FRC02.009 Description FO200-313G25n W7HP64FRGB1 MC UMACrk 2G+1G/250/6L2.2/5R/...
  • Page 175 FO200- Thailand 314G32n FO200- Thailand 314G50n FO200- 314G50n FO200- Australia/ 314G32n Zealand FO200- Australia/ 314G50n Zealand Appendix A Country Acer Part No LX.FRC02.013 LX.FRC02.010 S2.FRC02.005 LX.FRC02.007 LX.FRC02.002 LX.FRC02.004 LX.FRC02.008 S2.FRC02.003 S2.FRC02.002 S2.FRC02.001 LX.FRB02.007 LX.FRB02.006 LX.FRB02.005 S2.FRB02.004 LX.FRB02.001 LX.FRB02.002 Description FO200-312G25n W7HP64FRES1 MC UMACrk 2*1G/250/BT/6L2.8/5R/...
  • Page 176 Australia/ 312G25n Zealand FO200- Australia/ 312G32n Zealand FO200- 314G50n FO200- 314G32n FO200- 314G32n Country Acer Part No LX.FRB02.003 LX.FRB02.004 S2.FRB02.002 S2.FRB02.001 S2.FRB02.003 Description FO200-312G25n W7HP64FRAU1 MC UMAGCrk 1*2G/250/BT/6L2.8/5R/ CB_bgn_0.3D_G2K_AU_ES62 FO200-312G32n W7HP64FRAU1 MC UMAGCrk 1*2G/320/BT/6L2.8/5R/ CB_bgn_0.3D_G2K_AU_ES62 FO200-314G50n W7HP64FWW1 MC UMAGCrk 2*2G/500_L/BT/6L2.8/5R/ CB_bgn_0.3D_G2K_AU_ES64...
  • Page 177 Test Compatible Components This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions are tested under Windows Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
  • Page 178 Wiping Cloth Wireless Foxconn 3rd WiFi 1x2 Qualcomm Gobi2000 Description Keyboard ACER NT-1T Ferrari California Internal 11 Standard Black NONE Texture Atheros AR8131L PIFA Realtek Audio Codec ALC272X ABS UV Red Mirror w/Camera Foxconn Bluetooth BRM 2046 BT2.1 (T60H928.33) f/w:861...
  • Page 179 This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d.

  • Page 181: Index

    Antennas Removing 89 Battery Pack Removing 42 BIOS ROM type 18 vendor 18 Version 18 – BIOS Utility Advanced 26 Boot 29 Exit 30 Navigating 23 Save and Exit 30 Security 26 System Security 30 Bluetooth Module Removing 65 brightness hotkeys 12 Button Board Removing 62...
  • Page 182 Removing 69 LCD Module Disassembly Flowchart 79 LCD Panel Removing 84 Main Unit Disassembly Flowchart 54 Mainboard Removing 71 media access on indicator 8 Memory Check Microphone Removing 84 Model Definition No Display Issue num lock on indicator 8 ODD Failure Online Support Information optical drive module Panel...

This manual is also suitable for:

Ferrari one series

Table of Contents