Advertisement
2. INTRODUCTION
Cleans carpets, car interiors, fabrics and upholstery. Supplied complete with carpet lance, hand held pistol tool and full wet and dry vacuum
accessory kit. Powerful pump forces cleaning fluid into fabric and 1000Watt suction power leaves surface virtually dry after one pass.
This machine can be used in three ways:
2.1.
As a dry vacuum cleaner. The cartridge filter MUST be fitted. Use regular vacuum accessories. Press ONLY the black switch marked
"MOTOR".
2.2.
As a wet vacuum cleaner. The foam filter MUST be fitted. Use regular vacuum accessories. Press ONLY the black switch marked
"MOTOR".
2.3.
As a valeting machine. The foam filter MUST be fitted. Use valeting accessories. Press both "Motor" and "Pump" switches. Make first
pass over carpet with both switches depressed, then switch off pump to pick up remaining fluid.
WARNING: USE OF INCORRECT FILTER WILL INVALIDATE WARRANTY.
3. PREPARING FOR USE
3.1.
To remove the motor unit, undo the clips on the side of the tank and lift off (Fig 1).
When replacing motor unit ensure that the clips are correctly located. Check correct filter is fitted.
3.2.
For dry/wet cleaning use regular accessories. For valeting use, select either hand held spray head
or carpet lance.
3.3.
For use as vacuum cleaner.
Release the appliance head motor from the container and turn it upside down.
Remove detergent tank (Fig 2).
Position the filtering element (b) on the motor support (c) (Fig 3). Fit the plastic adaptor disk (a) on
the filtering element (b) and turn knob in a clockwise direction to connect the two parts together
(Fig 3). Replace the motor head and snap back the hooks.
The filter cartridge should be used for vacuuming dust and solid matter. It can be used with a
paper dust bag which avoids clogging of the filter cartridge and provides a quick, hygienic means
of emptying the cleaner.
Avoid sucking up sharp or damp material.
DO NOT SUCK DRY OBJECTS, DUST ETC WITHOUT FILTER IN PLACE.
3.4.
For using as valet machine remove the cartridge (Fig 4) filter and fit the foam filter supplied.
Put the detergent tank in place.
IMPORTANT: When the motor emits a high pitched sound turn off the machine and empty the
tank. Never completely immerse the nozzle in order to ensure partial air flow.
4. FOR USE AS A VALETING MACHINE
4.1.
Firstly set the machine up in the vacuum mode with the vacuum accessories and remove excess dirt from carpet, car or upholstery.
Then empty the container, remove the cartridge filter and fit the foam filter. Insert the detergent tank into the machine.
4.2.
USE OF DETERGENT.
Fill the white tank with COLD water up to the "max" level. Add 20cl of SEALEY "VM" or "SORMATOP 42" detergent (NOTE: 20cl is
about half a coffee mug) DO NOT USE ANY DETERGENT OTHER THAN SEALEY OR SORMATOP.
DO NOT increase the strength of detergent mix beyond 80-1. If part of the fabric is badly soiled, rub in (by hand) a mix of 80-1
detergent and leave for 2-3 minutes before valeting.
4.3.
Fitting the detergent equipment.
4.3.1. Insert the detergent supply trigger onto the handle and tighten the screw (Fig 5).
4.3.2. Fit the detergent supply tube onto the flexible hose using the clips provided (Fig 6).
4.3.3. Insert the detergent supply hose connection into the socket on the machine (Fig 7). To remove,
simply press the front ring and pull the connection gently out.
Connect the accessories in the following sequence:
4.3.4. The flexible hose to the appliance (Fig 8A).
4.3.5. The handle to the rigid extension tubes (Fig 8B).
4.3.6. The extension tubes to the suction head (Fig 9C).
4.3.7. The detergent pipe from the spray head into the socket on the handle (Fig 9D).
Fig 6
Fig 4
Original Language Version
Fig 7
Fig 1
Fig 2
Fig 3
Fig 8
Fig 9
PC320.V2
Fig 5
Issue: 2 - 13/01/10
Advertisement
