Samsung FlexWash DVE60M9900V Installation Manual

INSTALLATION GUIDE
FlexWash™
Parts supplied
Bolt hole covers Hose guide Tie strap Rubber cup
1
PREPARATION.
□ CHECK : The floor must be sturdy. (Carpet and soft tile surfaces are not permitted.
1. Check the installation location.
2. And move the washer to the installation location.
* When installing the washer on a pedestal, install the pedestal according to its manual.
2
UNPACKING WASHER.
CAUTION
When unpacking the washer, 2 person collaboration
is needed. To remove the cushion bottom of the
packing materials, forward dumping is strictly
prohibited. When you lay the washer down to
remove carton base, should protect the side of
washer and lay it carefully.
Make sure to lay the washing machine to its side.
Never lay your washer on its back or front.
 CAUTION: The shipping bolts must stay tightened during this unpacking.
3
REMOVING ALL SHIPPING BOLTS (7 BOLTS) DEPENDING ON THE MODEL.
Remove all shipping bolts at the
back of washer with spanner.
 CAUTION: Failure to remove the shipping bolts will cause vibration and noise.
4 COLD & HOT WATER HOSES INSTALLATION ON FAUCETS.
Rubber
Coupling
washer
Make sure a Rubber washer is Tighten Coupling by hand until
inside each coupling on both ends. it is snug.
 Water Supply is separately. To order, please refer to call center number on the back page of your " User Manual " .
5
WATER HOSES INSTALLATION ON WASHER.
COLD (Left) HOT (Right)
Water Water
Connect one end of the COLD/ Tighten Coupling by hand until
HOT water supply hoses to the it is snug.
each COLD/HOT water supply
intakes at the back of the washer.
 CAUTION: Make sure that the HOT & COLD hoses are not switched with each other.
Installation Guide-DC68-02580F-01_EN+CFR+MES.indd 1
Parts needed(Sold separately) Tools needed
Tape Carpen-
Water supply hoses
measure ter's level
When unpacking the washing
machine,a collaboration of
two persons is required.
Do not lay the machine on its
front face when removing the
bottom cushion.
Hold the shipping bolt with your Fill the holes with the supplied
hand and pull it through the bolt hole covers.
wide section of the hole. Repeat
for each shipping bolt.
Rubber washer
Then tighten two-thirds of a turn Run water in a bowl or basin to get
rid of any debris inside hose. Check
with pliers.
for HOT and Cold water supply.
Then tighten two-thirds of a turn For proper operation, make sure
with pliers. both Hot & Cold hoses from faucets
are connected to the corresponding
Hot / Cold water inlets on the washer.
6
CONNECTING THE DRAIN HOSE .
Flat screw-
Pliers spanner
drilver
Pipe
connector
Case 2. Laundry tub
96" Max
18" Min
Laundry tub must be no shorter
than 18 in (46 cm) and no longer
than 96 in (245 cm).
7
MOVE THE WASHER TO ITS FINAL LOCATION AND MAKE SURE IT IS LEVELED.
Confirm whether washer is well seated and does not shake. Adjust
leveling legs, if necessary.
8
LEVEL THE WASHER BY ADJUSTING THE FOUR LEVELING LEGS.
HOT COLD
Level the washer by turning the leveling wheel
clockwise or counter clockwise to the required level
with the spanner.
 CAUTION: Your washer must be leveled on all four sides. An unlevel washer may cause vibration.
9
Final Test : Water leakage , Vibration & Noise
1. Powering your washing machine.
2. Run a test cycle(Rinse+Spin) with small amount of laundry such as 4~5 Towels.
(1) Check for any leakage at the hose connections.
 If water leaks while water is being supplied or drained, check the water connections. (Refer to Step 4,5,6)
(2) Check for vibration and noise.
 If the washer rocks and vibrates excessively, level your washer again. (Refer to Step 7,8)
Visits by a Service Engineer to explain functions, maintenance or installation is not covered by warranty.
INSTALLATION
COMPLETION CHECKLIST
□
Washer plugged in, power OK
Upper The pipe connector is attached
drain
on the product.
hose Drain hose
Lower
To remove the pipe connector
drain
hose
from the product, separate the
pipe connector and the clamp
Hose guide
rings from the drain hose.
To keep the drain hose spout
To reassemble, follow the steps
bent, use the supplied plastic
in reverse order.
hose guide.
Case 3. Stand pipe Case 4. wall standpipe
Hose
retainer
Hose
retainer
85 mm
96" Max
18" Min
Tie strap
Tie strap
Do not insert the drain hose Insert the pipe connector into
too far into the stand pipe: 6 - 8 the wall standpipe.
inches, and no more.
Your washer must be leveled on all four sides. Use a carpenter's level
on all four corners of your washer to ensure it's level.
Check whether washer shakes and level
again, if necessary.
□
No water leakage
□
Water hose connected properly
□
Drain hose connected properly
French on back 
Spanish on back 
Case 1. Wash basin
The drain hose must be placed
at a height between 23.6 in
(60cm) and 35.4 in (90cm).
Make sure you face the tip of the
pipe connector downwards to
the drain hole.
When your washer is leveled, tighten
the locking nuts using the spanner or (-)
flathead screwdriver.
□
No vibration / noise
□
Washer leveled
□
Shipping bolts removed
DC68-02580F-01
2017-02-02 2:54:13