Subscribe to Our Youtube Channel
Related Manuals for Hoshizaki KM-590DWJ
Summary of Contents for Hoshizaki KM-590DWJ
- Page 1 KM-590DJ STACKABLE CRESCENT CUBER KM-590DWJ KM-590DJ-S KM-590DWJ-S INSTRUCTION MANUAL No. 15 Qingqiu Street, Suzhou Industrial Park, Suzhou 215126 China L1F137104 (051221)
-
Page 2: Table Of Contents
ENGLISH IMPORTANT This manual should be read carefully before the appliance is installed and operated. Read the warnings and guidelines contained in this manual carefully as they provide essential information for the continued safe use and maintenance of the appliance. Retain this manual for any further reference that may be necessary. -
Page 3: Important Safety Information
ENGLISH Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, damage to the appliance, or damage to property. WARNING Indicates a hazardous situation which could result in death or serious injury. - Page 4 ENGLISH WARNING, continued • Children should be properly supervised around the appliance. • Do not climb, stand, or hang on the appliance or allow children or animals to do so. Serious injury could occur or the appliance could be damaged. •...
-
Page 5: Specifications
The nameplate provides electrical and refrigerant data. The nameplate is located on the left panel. For certification marks, see the nameplate. We reserve the right to make changes in specifications and design without prior notice. 1. KM-590D_J/KM-590D_J-S Model KM-590DJ/ KM-590DWJ/ KM-590DJ-S KM-590DWJ-S Type Air-cooled, Water-cooled,... -
Page 6: Dimensions/Connections
ENGLISH B. Dimensions/Connections 1. KM-590DJ/KM-590DJ-S Units: mm WATER INLET 1/2''FPT Side ELECTRICAL SUPPLY Rear 24mm DIA OPENING WATER INLET DRAIN 1/2''FPT WATER INLET 3/4" FPT ELECTRICAL SUPPLY 1/2''FPT 24mm DIA OPENING CONDENSATION ELECTRICAL SUPPLY DRAIN DRAIN OUTLET 24mm DIA OPENING 3/4"... - Page 7 ENGLISH 2. KM-590DWJ/KM-590DWJ-S Units: mm WATER INLET Rear 1/2"FPT Side ELECTRICAL SUPPLY WATER INLET 24mm DIA OPENING DRAIN WATER INLET 1/2"FPT 3/4" FPT 1/2"FPT ELECTRICAL SUPPLY ELECTRICAL SUPPLY 24mm DIA OPENING DRAIN 24mm DIA OPENING DRAIN CONDENSATION 3/4" FPT 3/4"...
- Page 8 ENGLISH Intentionally Left Blank...
-
Page 9: Installation And Startup Instructions
• This icemaker can be installed on a storage bin 48" to go below 0°C. For details, see "III.C. Preparing the wide or wider. For options, contact your local Hoshizaki Icemaker for Long Storage." distributor. -
Page 10: D.setup
ENGLISH c. Use the thumbscrew removed in the previous step D. Setup and the thumbscrew included in the accessory bag to secure the bin control assembly to the bottom of the CAUTION icemaker. See Fig. 4. Before operating the icemaker, the bin control d. -
Page 11: Installation Of Upper Unit
ENGLISH Upper Unit Connection Overview 6) Level the icemaker and storage bin in both the left-to-right and front-to-rear directions. Adjust the Lower Unit Wire Harness Connector B/ storage bin legs to make the icemaker level.7 Upper Unit Wire Harness Connector A 7)Replace the panels and storage bin baffle in their Upper Unit Wire Harness correct positions unless you are installing an upper... -
Page 12: Electrical Connection
ENGLISH • The opening for the power supply connection is F. Electrical Connection 7/8" (22.2 mm) DIA to fit a 1/2" trade size conduit. • If a power cord is used to provide electricity to the WARNING icemaker in place of a hard-wired (conduit) connection, a strain relief (gland) of the appropriate size for the For All Models power cord must be installed at the 7/8"... -
Page 13: Installation Of Remote Condenser Unit
3) Install Parker quick connect couplings on each • A dry and well ventilated area with 61 cm clearance in end. OS-QUICK, an optional Hoshizaki universal both front and rear for proper air circulation and ease quick connect coupling kit, is recommended. - Page 14 R-404A for each meter over 20 m to a maximum of 30.5 refrigerant oil or Parker Super O Lube only. m. Your nearest Hoshizaki Service office is available for recommendations. c. Make sure the male fitting and female coupling are...
- Page 15 ENGLISH 6. Electrical Connection • Usually an electrical permit and services of a licensed electrician are required. WARNING • The opening for the power supply connection is 7/8" (22 mm) DIA to fit a 1/2" trade size conduit. 1. Electrical connection must meet national, state, and 1) Remove the louver panel.
- Page 16 ENGLISH 7. Stacking Remote Condenser Units 1) Install the lower remote condenser unit as described earlier in this section. 2) Place the upper remote condenser unit on top of the lower. See Fig. 15. 3) Secure the upper remote condenser unit to the lower remote condenser unit with the 4 screws provided.
-
Page 17: Water Supply And Drain Connections
• External filters, strainers, or softeners may be required depending on water quality. Contact your local See Fig. 16, 17, or 18 Hoshizaki distributor for recommendations. WARNING • The icemaker and condensation drain line(s), storage bin drain line, and water-cooled condenser drain line 1. - Page 18 Vent Tube Condensation Drain Outlet 3/8" (9.5 mm) OD Hard Tube 5-cm air gap Bin Drain Outlet Minimum 3/8" (10 mm) See Manufacturer's Instructions Nominal Hard Pipe Floor Drain KM-590DWJ/KM-590DWJ-S Fig. 17 Connection to an Open Drain System...
- Page 19 Minimum 3/4" (18 mm) Nominal Hard Condensation Pipe 5-cm air gap Drain Outlet 3/8" (9.5 mm) OD Hard Tube Vent Tube Bin Drain Outlet See Manufacturer's Instructions Floor Drain Fig. 18 KM-590DWJ/KM-590DWJ-S Connection to a Closed Loop System...
-
Page 20: Final Checklist
ENGLISH I. Final Checklist WARNING Separators CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within 7°C to 38°C and the water temperature within 7°C to 32°C all year around? 3) Is there at least 15 cm clearance at sides, rear, and top... -
Page 21: Startup
Performed by Qualified Service Technician operate for a total of 10 minutes. Hoshizaki recommends cleaning and sanitizing this unit at 6) Turn off the power supply, then remove the front panel. least once a year. More frequent cleaning and sanitizing, however, may be required in some existing water 7) Remove the insulation panel. -
Page 22: Maintenance
25) Remove the drain plug. Allow the water tank to drain. Replace the drain plug and the insulation panel in 1) Dilute 800 ml of Hoshizaki "Scale Away" with 19 l their correct positions. of warm water or prepare the other recommended Note: Do not replace the insulation panel when you proceed to "2. -
Page 23: Preparing The Icemaker For Long Storage
IV. WARRANTY When the icemaker is not used for two or three days under Hoshizaki warrants to the original owner/user that all Hoshizaki normal conditions, it is sufficient to move the control switch branded products shall be free of defects in material and/or to the "OFF"...
Need help?
Do you have a question about the KM-590DWJ and is the answer not in the manual?
Questions and answers