Page 1
Owner's Manual & Assembly Instructions Model No. HM10667 RMG106 RMW106 VH106-A CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ 709521207 SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION.
Page 2
Anchoring and foundation materials are not included with your building. We recommend the combined use of an Arrow Floor Frame Kit and an Arrow Anchoring Kit as an effective method of securing your building to the ground (Available by mail order or at your local dealer) or you may construct a foundation and anchoring system of your choice.
PLAN AHEAD..Watch the Weather: Be sure the day you select to install your building is dry and calm. Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Teamwork: Whenever possible, two or more people should work together to assemble your building.
Page 4
SAFETY FIRST..Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various •Practice caution with the tools being used in the pieces of your building since some contain assembly of this building. Be familiar with the sharp edges.
Page 5
Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy amounts of snow on roof can damage building making it unsafe to enter. In snow country, Roof Strengthening Kits are available for most Arrow Buildings for added protection against heavy snow accumulation.
Page 6
For buildings ATTIC KIT / WORKBENCH KIT larger than 10'x9', use 2 kits. Heavy-duty galvanized steel bars that fit all 10' wide Arrow buildings. They Model No. AK100 install quickly and easily to help New concrete anchor system permits...
Page 9
OPTION 1: ARROW FLOOR FRAME KIT: (Order No. FB106-A or 68381-A) Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This kit should be used with one of the following: A.
Page 10
It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Anchoring into Wood/Post: Arrow Anchoring Kit: (Model No. AK4 or 60298) Use 1/4" Wood Screws. There are 1/4" (0,63cm) dia.
Page 11
65109 67468 66646 66045 #8-32 Acorn Nut (4) Peak Cap (2) Washer (301) Handle (2) (Packed with Screws) (Arrow Logo) (8 sheets of 40) 66183 66769 66382 Roof Trim Cap 6228 Door Slide (4) Lower Door Guide (4) (2 right & 2 left)
Parts List Assembly Part Part Quantity Check Key No. Number Description in Carton List 5986 Rear Wall Angle 6403 Door Track Splice 10497 Horizontal Door Brace 6635 Gable Brace 6529 Roof Panel 6000 Right Gable 6001 Left Gable 3719 Door Handle Brace 8461 Ridge Cap 8468...
Page 14
● ● ● ● ● 8934 Ramp (1) ● Parts Needed For ● Step 1 ● ● ● ● ● 9367 Front Floor Frame (2) Floor Frame Assemblies ● ● ● ● ● 8936 Rear Floor Frame (2) The front floor frame is made up of three pieces.
● Parts Needed For ● ● ● ● ● ● 5986 Rear Wall Angle (2) Step 2 ● ● ● ● ● 9917 Rear Wall Channel (2) Frame Assemblies Rear Wall Channel 9917 The main frame pieces reinforce the 118 1/8" 3,0m 9917 walls.
Page 16
● Parts Needed For ● ● ● ● ● ● 8474 Roof Beam (1) Step 3 ● ● ● ● ● 8476 Side Wall Angle (1) Roof Beam Assembly The roof beams join the two gables and support the roof panels. The main roof beam is made up of two pieces fastened together.
Page 17
● Parts Needed For ● ● ● ● ● ● 6403 Door Track Splice (1) Step 4 ● ● ● ● ● 9366 Door Track (2) Door Track Assembly NOTE: Door Track Splice (painted part) The door track assembly supports the sliding doors and reinforces the front wall.
Page 18
● ● ● ● ● Front Floor Assembly (1) ● Parts Needed For ● Step 5 ● ● ● ● ● 8946 Side Floor Frame (2) Floor Frame ● ● ● ● ● Rear Floor Assembly (1) RIGHT REAR 8946 STEP Assemble the four corners of the floor frame using two screws at each...
Page 19
● Parts Needed For ● ● ● ● ● ● 6627 Wall Panel (2) Step 6 ● ● ● ● ● 9374 Front Wall Panel (2) Corners ● ● ● ● ● 8471 Corner Panel (4) NOTE Narrow The remainder of the building assembly Side 8471 requires many hours and more than one...
Page 21
● Parts Needed For ● Step 8 ● ● ● ● ● 6627 Wall Panel (6) Wall Panels Each wall panel has a crimped rib on STEP one side. The crimped rib should go 6627 6627 under the rib of the panel that follows 6627 6627 STEP...
Page 22
● Parts Needed For ● ● ● ● ● ● 9370 Door Jamb (2) Step 9 ● ● ● ● ● 9365 Front Wall Channel (2) Front Channel/Door Jamb The door jambs reinforce the door opening and provide an attractive 9365 trim.
Page 23
● Parts Needed For ● ● ● ● ● ● 6000 Right Gable (2) Step 10 ● ● ● ● ● 6001 Left Gable (2) Gable Assemblies ● ● ● ● ● 5971 Roof Beam Bracket (4) The gables go on top of the front and rear walls to support the roof beams.
Page 24
● ● ● ● ● Left Gable Assemblies (2) ● Parts Needed For ● Step 11 ● ● ● ● ● Right Gable Assemblies (2) Gables/Braces ● ● ● ● ● 6635 Gable Brace (2) Lift and fasten a right and left gable, under angle at corner, to the door track and rear wall angle with screws.
Page 25
● Parts Needed For ● ● ● ● ● ● Main Roof Beam (1) Step 12 ● ● ● ● ● 8474 Roof Beam (2) Roof Beams Fasten the main roof beam to the gable brace of the front gable. STEP Fasten the other end of the main roof beam to the gable brace of the...
Page 26
● Parts Needed For ● Step 13 ● ● ● ● ● 8468 Right Roof Panel (1) Right Roof Panel STEP Installing the roof panels is best done with a step ladder. Begin installing roof panels at the back right corner of 8468 8469 the building.
● Parts Needed For ● ● ● ● ● ● 8469 Left Roof Panel (2) Step 14 ● ● ● ● ● 6529 Roof Panel (4) Roof Assembly ● ● ● ● ● 8468 Right Roof Panel (1) STEP STEP 8469 Left Roof Panel Weather Stripping Tape Roll...
Page 28
● Parts Needed For ● Step 15 ● ● ● ● ● 8461 Ridge Cap (1) Ridge Cap Install the ridge cap on the com- pleted roof section using bolts and nuts. Do not fasten the ends of the ridge cap at this time. Fasten the lower end of the panels to the side wall angles using screws and washers.
Page 29
● Parts Needed For ● Step 16 ● ● ● ● ● 8482 Side Roof Trim (2) Roof Trim Attach the side roof trim to the lower end of the roof panels on each side of the building using screws at each panel overlap.
● ● ● ● ● 3719 Door Handle Brace (2) ● Parts Needed For ● ● ● ● ● ● 10477 Right and Left Doors (2) Step 17 ● ● ● ● ● 10497 Horizontal Door Brace (4) Door Assembly ●...
Page 31
● Parts Needed For ● ● ● ● ● ● Right Door Assembly (1) Step 18 ● ● ● ● ● Left Door Assembly (1) Door Installation & Adjustment Horizontal Door Brace Gable Door Track Door Slide From inside the building, put the bottom of the right door assembly (on your left when you are inside the building) behind door jamb into the...
Page 32
HM10667 RMG106 RMW106 VH106-A SOME FACTS ABOUT RUST 1. Avoid nicking or scraping the coating surface, Rusting is a natural oxidizing process that occurs inside and out. when bare metal is exposed to moisture. Problem 2. Use all the washers supplied. In addition to pro-...
Need help?
Do you have a question about the HM10667 and is the answer not in the manual?
Questions and answers