Advertisement
Remote Connections
Your booth incorporates advanced circuitry allowing it to connect and
communicate with most remote control systems. The unit is shipped
with a Remote Control Bypass Plug installed. Your booth will not oper-
ate without either the bypass plug or a remote system connected.
WIRED REMOTE
WIRELESS REMOTE
PORTS (RJ-22)
PORT (RJ-11)
If a remote system is to be used, first determine whether the remote sys-
tem is a TMax® System or a standard remote system operating with a
control relay. Follow the appropriate instructions for your system type.
T-Max® Products
The T-Max® remote systems offer the ultimate in sunbed control, while
allowing the tanner easy straightforward operation. Your booth is con-
figured to directly connect to this system, including the new wireless
remote system. The circuitry inside your booth eliminates the need for
the T-Max® 1A or 3A when connecting to the TMax® Manager series.
Your booth supports the auto addressing feature of the latest T-Max®
Manager models and the following parameters:
5, 6, 7, 8, 9, 10, 15 and 23. See your T-Max® manual for descriptions
of these parameters and how they function.
T-Max® Wireless Remote System
The T-Max® G2 eliminates wires in your salon, allowing easy setup
without hiring an electrician to run wires. It also protects your invest-
ment from damage by isolating each unit from one another. Your
booth arrives "wireless ready", which means it connects directly to
the T-Max® wireless system. Older tanning beds, and T-Max® man-
agers, also utilize this system but require a T-Max "Power Injector"
(PI) to provide the needed power to the wireless unit.
Remote System Hook-up Scenarios
Follow the diagrams below and on the next page to see the many differ-
ent scenarios for hooking up your salon. If you need further assistance,
call T-Max® directly at (417) 272-0761.
Scenario 1 - T-Max® Manager Series with Complete Wireless
Connect one G2 (with Power Injector) to the Manager and one G2 to
each of the tanning units. Install as many beds as you like with this
configuration. Units that do not communicate with T-Max will need a
G2 with Power Injector and an additional 3A to operate. If you have
an older T-Max® Manager that doesn't support auto addressing, set the
address of each sunbed manually as described in Setting the address
manually. You can place your booth at any location in the series.
4
The remote connection is not designed to supply or accept high
voltage, nor can it provide power to an external timer. The sunbed's
remote interface circuitry operates on 5 volts, attempting to connect
it to any higher voltages will damage the sunbed as well as void your
warranty.
Scenario 2 - T-Max 3A with Wireless
In single sunbed installations, the T-Max® 1A and 3A can offer the
same control as the T-Max® Manager, eliminating the need for a Man-
ager. If you're using a 1A in this manner, it must have a chip labelled
"master" installed on its circuit board. The remote control bypass plug
must not be used in this configuration. The 3A may be used as a "mas-
ter" with no modification.
After you have set the T-Max® 1A's,
or 3A's, address to "0" (refer to your
T-Max® user's guide) and the booth's
address to "1", simply connect one G2
(with Power Injector) to the T-Max® 3A
and one G2 to the booth.
Scenario 3 - T-Max® Manager Series with Wireless combination 2
Connect one G2 (with Power Injector) to the Manager and one G2
to a wireless ready tanning bed. The rest of the salon may be "dai-
sychained" together and connected to the wireless equipped tanning
bed, eliminating the need to wire the Manager to the tanning beds.
Scenario 4 - T-Max® Manager Series with Wireless combination
Wireless can be easily added to an existing salon already utilizing
TMax ®. Connect one G2 (with Power Injector) to the Manager and
one G2 to each wireless ready tanning bed. The rest of the salon may
be "daisy-chained" together and connected to the Manager.
CAUTION
Advertisement
