Advertisement
Quick Links
Shock hazard.
Disconnect power before servicing or removing any pro-
tective covers.
Do not operate this device near water or while you are
wet.
Some medications may increase your sensitivity to ultraviolet light. It
is recommended that you consult a physician before using this booth if
taking any medication, or if you suspect that your skin might be espe-
cially sensitive to sunlight.
Wear protective eyewear.
Failure to may result in severe burns or longterm injury to the eyes.
Air from the room is used to cool the unit. Maximum ambient room
temperature should be 80°F. Place your booth no closer than 6" from
any wall. Make sure nothing obstructs the airflow into the booth's
endcaps or out of the fan openings. A poorly ventilated room may
cause the unit to become hot and cause discomfort to the user.
Electrical Requirements
Your booth operates from a 208V AC source. You should have a NEMA
6-30R electrical outlet (below), on a dedicated circuit capable of pro-
viding 30 Amp service, installed in the room in which you will use
the unit. We recommend installation by a professional electrician. The
outlet must be earth grounded.
Hardware Inventory
(Plus a small pillow and eyewear)
Shoulder Bolt
Quantity 4
Flanged Sleeve Bushing
Quantity 4
Nylon Flat Washer
Quantity 4
3/8" Washer, Black
Quantity 4
3/8-16 Locknut, Black
Quantity 4
#12 x 3" Screw
Quantity 1
DANGER
DANGER
WARNING
CAUTION
30 AMP NEMA #6-30R
RECEPTACLE
Hex (Allen) Wrench
Quantity 1
You Will Need:
#2 Phillips
Screwdriver
9/16" Wrench
Platinum
48
PRO
Unpacking and Inspection
Your booth arrives in three cardboard cartons. Pull back the plastic
sheet and, with a helper, grasp each unit and pull it from the carton
bottom, leaving the plastic wrap and the carton packaging. Do not try
to lift the unit with the plastic still on as it may slip.
The Control Unit box contains the hardware kit and a body fan.
Inspect the items and make sure they are free from any visible damage.
Report the extent of any damage to the transportation company.
Assembly Procedures
CONTROL UNIT
X
1
Connect the Side Unit to the Control
Unit (with timer), as shown. Both units
have legs. The Door Unit has wheels.
Be sure the white Nylon Washer is be-
tween the hinge brackets.
LEGS
10351A
Advertisement
Summary of Contents for Sunfire Platinum PRO48X
- Page 1 Platinum Unpacking and Inspection DANGER Shock hazard. Your booth arrives in three cardboard cartons. Pull back the plastic sheet and, with a helper, grasp each unit and pull it from the carton Disconnect power before servicing or removing any pro- bottom, leaving the plastic wrap and the carton packaging.
- Page 2 Using a #2 Phillips screwdriver, remove the center screw securing the top endcap on the Side Unit, indicated by the arrow. The Side Brace keeps the Control Unit and Side Unit from opening up. Position the two units as shown, and insert the pins on the Side Brace into the holes in the extrud- ed bosses on the endcaps.
- Page 3 SEULES LES LAMPES SUIVANTES ONT ÉTÉ HOMOLOGUÉES POUR CET ÉQUIPEMENT : Sunfire® Plus Modèle FR71/160W CAUTION: To achieve compliance with Canadian Standards Association’s (CSA) stan- dard CAN/CSA C22.2 No. 224, connect only to a circuit protected by a Class A Ground Débrancher l’alimentation électrique avant de nettoyer l’appareil ,...
- Page 4 Remote Connections CAUTION Your booth incorporates advanced circuitry allowing it to connect and The remote connection is not designed to supply or accept high communicate with most remote control systems. The unit is shipped voltage, nor can it provide power to an external timer. The sunbed’s remote interface circuitry operates on 5 volts, attempting to connect with a Remote Control Bypass Plug installed.
- Page 5 Setting the address manually Scenario 5 - T-Max® Manager Series with wires Before connecting your booth to the T-Max® Manager or T-Max® 1A or As always, this tanning booth is fully compatible with a wired T-Max® 3A, the address of your booth must first be set. Set the address manually system.
-
Page 6: Care And Maintenance
Operation Care and Maintenance Cleaning After Use A Timer display - Displays remaining time. Clean and disinfect areas you touch after each use. Use a non-abrasive B Timer button - Turns booth on. Timer disinfectant cleaner (such as a mixture of 2oz of Lucasol™ disinfectant display shows remaining time. -
Page 7: Troubleshooting
“0”. (example: Display shows 08 then 54. This equals 854 hours.) NOTE: If the unit is connected to a TMax® Sunfire® Plus FR71/160W remote device, it may briefly lose communication with the remote. This is normal. -
Page 8: Limited Warranty
SUNFIRE INDUSTRIES will advise the Purchaser of the nature of the problem and the cost to yond the range of normal usage, or by accident, fire or other hazard. Repair or replacement of a the Purchaser based on the proration of the defective system or component.