Maintenance; Residual Risks - Ryobi RBL1850S Original Instructions Manual

WARNING
If the product is dropped, suffers heavy impact or begins
to vibrate abnormally, immediately stop the product and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service centre.
To reduce the risk of injury associated with contacting
rotating parts, always stop the machine, remove the battery
pack, and make sure all moving parts have stopped:
● before cleaning or clearing a blockage
● when leaving the product unattended
● before installing or removing attachments
● before checking, maintaining or working on the
product
● if the machine starts to vibrate abnormally (inspect
immediately)
BLOWER SPECIFIC SAFETY WARNINGS
■ Wear a face filter mask in dusty conditions to reduce
the risk of injury associated with the inhalation of dust.
■ Slightly dampen surfaces in dusty conditions.
■ Do not point the blower nozzle in the direction of people
or pets.
■ Never place objects inside the blower tubes.
■ Do not operate the product near open windows.
■ Use the full blower nozzle extension so that the air
stream can work close to the ground and perform
effectively.
■ Do not place blower on top of or near loose debris.
Debris can be sucked into the intake vent, resulting in
possible damage to the product.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow a fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
TRANSPORTATION AND STORAGE
■ Stop the product, remove the battery, and allow it to
cool before storing or transporting.
■ Clean all foreign materials from the product. Store the
product in a cool, dry, and well-ventilated place that
is inaccessible to children. Keep away from corrosive
agents, such as garden chemicals and de-icing salts.
Do not store outdoors.
■ For transportation in vehicles, secure the product
against movement or falling to prevent injury to persons
or damage to the product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.

MAINTENANCE

WARNING
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can
cause possible injury and poor performance, and may
void your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service, bring the product to an
authorised service centre. When servicing, use only
identical replacement parts.
■ To reduce the risk of injury associated with contacting
rotating parts, always stop the machine, remove the
battery pack, and make sure all moving parts have
come to a complete stop:
● before cleaning or clearing a blockage
● when leaving the product unattended
● before installing or removing attachments
● before checking, maintaining or working on the
product
● if the machine starts to vibrate abnormally (inspect
immediately)
■ Do not make adjustments and repairs not described in
this manual. For other repairs, contact an authorised
service agent.
■ After each use, clean the product with a soft dry cloth.
■ Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure that the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
■ Bring the product to an authorised service centre to
replace damaged or unreadable labels.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
■ Injury caused by vibration. Always use the right tool for
3