PR-600 Series HPRT-HT100 User Manual Contents Manual Information ..........................1 Important Safety Instructions ......................2 Chapter 1 Introduction ......................... 5 1.1 Packing List ............................5 1.2 Appearance and Components ......................6 1.3 Dimension ............................7 Chapter 2 Specifications ........................8 Chapter 3 Installation &...
Page 3
Without any written permission from our company, any section of this manual is prohibited to be copied or transferred in any form. Copyright This manual is printed in 2017, the copyright belongs to IDZOR TECHNOLOGIES CO., LTD. Printed in China 1.0 Version...
PR-600 Series HPRT-HT100 User Manual Manual Information This user manual contains basic information for product usage as well as for emergency measures that may be required. The installation and usage of printer driver, utility tool and HPRT BarTender® Ultralite are also included in the manual.
PR-600 Series HPRT-HT100 User Manual Important Safety Instructions Before using the appliance, please carefully read the following safety regulations in order to prevent any hazard or material damage. 1.Safety warning Warnings: The print head will become very hot during printing; avoid contact with the print head after printing has finished.
Page 6
PR-600 Series HPRT-HT100 User Manual Note: Violating following instructions may cause slight damage of the appliance. 1) If you observe a strange smoke, odour or noise from the printer, unplug it before taking following measures. • Switch off the printer and unplug the set from the mains.
Page 7
PR-600 Series HPRT-HT100 User Manual 3.Other Precautions The copyright for this user manual and various other manuals is property of our company. Any copying or conversion into electronic form and saving of this material without the express written permission is strictly prohibited. Use of the information contained in this manual is not subject to any patent liability.
PR-600 Series HPRT-HT100 User Manual Chapter 1 Introduction 1.1 Packing List Note: 1. Unpack the printer and keep the packing material in case you need to ship the printer in the future. 2. Any damages exist, please contact the local dealer.
PR-600 Series HPRT-HT100 User Manual 1.2 Appearance and Components ■ Front View ■ Rear View ■ Inside View Note:The views above are for your reference. Ports vary by your choice. Rev.1.0...
PR-600 Series HPRT-HT100 User Manual Chapter 3 Installation & Usage 3.1 Media Loading 3.1.1 Paper Roll Loading 1.Pull and lift the cover. 2.Pull the roll holders open and place the roll between them. Rev.1.0...
Page 14
PR-600 Series HPRT-HT100 User Manual 3.Press down the locking tab. 4.Pass the labels through label guides and adjust label guides to label’s width. Note: If your printer is under Thermal Line Printing Method, press down the printer cover until it snaps closed. Otherwise, continue the procedure in chapter 3.1.2.
Page 15
PR-600 Series HPRT-HT100 User Manual 3.1.2 Ribbon Loading 1. After putting rewind spindle through printhead module, insert the right side of supply spindle into the rear pin, and then insert the left side into the rear wheel. Then do the same procedure for the ribbon rewind spindle.
Page 16
PR-600 Series HPRT-HT100 User Manual 3. Press the lock and close the cover slightly. 4. Press down the cover until it snaps closed. Rev.1.0...
Page 17
PR-600 Series HPRT-HT100 User Manual 3.1.3 External Paper Roll Loading If the paper roll is extremely large, users can load the paper roll outside (See the graph at right). Pass the paper through the external feed slot and then through paper guides.
PR-600 Series HPRT-HT100 User Manual 3.2 Power Connection 1.Make sure the printer’s power switch is in the off position. 2.Connect the AC adapter to power receptacle. 3.Connect the power cord to AC adapter. 4.Connect the other end of power cord to the outlet.
PR-600 Series HPRT-HT100 User Manual 3.3 Peripherals Connection 3.3.1 Interface Cable Connection The standard for the printer’s interface cable shows in the following. - USB B-Type Cable - RS-232C Cable - RJ45 Cable Please follow the instructions to connect the cable.
PR-600 Series HPRT-HT100 User Manual 3.4 Detection When printing paper, the moveable label sensor is used to detect paper. The label sensor moves differently when using various kinds of paper. If user moves the sensor improperly, paper may not be detected, therefore the printer could not print paper.
Page 21
PR-600 Series HPRT-HT100 User Manual Figure 2 (Left) Rev.1.0...
Page 22
PR-600 Series HPRT-HT100 User Manual 3.4.2 Labels When printing labels (Figure 3) or double-row labels (Figure 4), the sensor shall be aimed at the left photoelectric hole (Figure 5), which is the original position. Figure 3 (Labels) Figure 4 (Double-row Labels)
Page 23
PR-600 Series HPRT-HT100 User Manual Figure 5 (Left) Rev.1.0...
Page 24
PR-600 Series HPRT-HT100 User Manual 3.4.3 Punched Hole Label When printing punched hole labels, move the sensor until it’s aimed at the right photoelectric hole (Figure 6). Figure 6 (Right) Rev.1.0...
Page 25
PR-600 Series HPRT-HT100 User Manual 3.4.4 Blackmark Paper When printing blackmark paper (Figure 7), the sensor shall be aimed at the position of black mark (Figure 8). Figure 7 (Blackmark Paper) Figure 8 (aimed at blackmark’s position) Rev.1.0...
PR-600 Series HPRT-HT100 User Manual 3.5 Operation Panel 1.FEED button Turn on the printer. Press the feed button, and printer will automatically feed a label under “Label Mode”. Press the feed button, and the printer will feed the fixed distance under “Continuous Mode”.
PR-600 Series HPRT-HT100 User Manual 3.6 Basic Function 3.6.1 Power On/ Power Off Press “O” to power off the printer. Press “l”to power on the printer. 3.6.2 FEED Button 1.Turn on the printer. Press the feed button, and printer will automatically feed a label under “Label Mode”.
Page 28
PR-600 Series HPRT-HT100 User Manual 3.6.4 Print Self-test Page The self-test checks the printer’s current settings, status and whether the printer has any problems or not. 1.Printing Manually 1) Make sure the roll is loaded properly. 2) Make sure the top cover of the printer is closed properly. Then turn on the printer.
PR-600 Series HPRT-HT100 User Manual Chapter 4 Interface 4.1 USB Interface SIGNAL NAME VBUS 4.2 Other Optional Interfaces Serial Port SIGNAL NAME +5VDC Rev.1.0...
Page 30
PR-600 Series HPRT-HT100 User Manual Ethernet Port SIGNAL NAME Rev.1.0...
PR-600 Series HPRT-HT100 User Manual Chapter 5 Maintenance & Adjustment Adhesives and coatings of the media can transfer to the printer parts over time along the media path including the thermal print head and media sensor. This build-up can accumulate dust and debris. Failure to clean the print head, media path, and media sensor could result in inadvertent loss of labels, label jams and possible damage to the printer.
PR-600 Series HPRT-HT100 User Manual 5.3 Cleaning Roller and/or Paper Path 1) Open the printer cover and then remove the paper. 2) Remove any dust or foreign substance using dry cloth or cotton swab. 3) Soak the cloth or cotton swab in alcohol for medical use and use it to remove adhesive foreign substances or other pollution materials.
PR-600 Series HPRT-HT100 User Manual Chapter 6 Printer Utility Tool Instructions 6.1 Installation Preparation Download application program in CD. eg: HPRTUtilityForLabel_Channel V2.0.0.3. 6.2 Usage Note: The screen may vary slightly by different operating systems and models. Take printer HT100 as example. Please refer to printer HT100 when using printer HT130.
Page 34
PR-600 Series HPRT-HT100 User Manual (2) Add/Modify/Delete Printer, Connect Test. ●Click “Add Printer”. Choose the printer and port (eg: USB), then click “OK”, showed in “Printer List”. Rev.1.0...
Page 35
PR-600 Series HPRT-HT100 User Manual ●Click “Modify Printer”. Choose the printer and port(eg: COM1), then click “OK”, showed in “Printer List”. Rev.1.0...
Page 36
PR-600 Series HPRT-HT100 User Manual ●Click “Delete Printer”. Click “OK” to delete the printer, and click “Cancel” to cancel the command. ●Click “Connect Test” to test whether the connection is successful or not. If connection succeeds, it shows as follows.
Page 37
PR-600 Series HPRT-HT100 User Manual (3)Function. ●Click “Printer Information”, showing printer information.(varies by different printers) ●Click “Print Test Text”. Type the text and set up the printing range. Click “Print”, then printer starts to print the test text. ●Click “Print Self Information”, then printer starts to print self-test page.
Page 38
PR-600 Series HPRT-HT100 User Manual ●Click “Parameter Setting”. User can set up the BT config, print type, paper mode and so on. Click “Set”, and back to the main menu. ●Click “Model Print Test”, then printer starts to print models.
PR-600 Series HPRT-HT100 User Manual Chapter 7 Seagull Windows Driver Instructions 7.1 Introduction The following operating systems are supported: Microsoft Windows 10 (32 bit/64 bit) Microsoft Windows 8 (32 bit/64 bit) Microsoft Windows 7 SPI (32 bit/64 bit) Microsoft Windows Vista SP2 (32 bit/64 bit)
PR-600 Series HPRT-HT100 User Manual 7.3 Installation Note: Under different operating systems, the screen may be slightly different. Take Windows 7 as example. Take printer HT100 as example. Please refer to printer HT100 when using printer HT130. To avoid the prevention, recommend to close the security software before installation.
Page 41
PR-600 Series HPRT-HT100 User Manual 5.Choose the installation directory, then click “Next”. 6.Click "Finish". Rev.1.0...
Page 42
PR-600 Series HPRT-HT100 User Manual 7.Choose "Install printer drivers", then click "Next". Note: If you have connected the printer to computer, it will detect and install the driver automatically. (eg.: USB port) 8.Choose "Install a driver for a Plug and Play printer, then click "Next".
Page 43
PR-600 Series HPRT-HT100 User Manual 9.Enter a name for this printer, then click "Next". 10.Click"Finish". Rev.1.0...
Page 44
PR-600 Series HPRT-HT100 User Manual 11.Click "Close", and the printer driver is installed successfully. 12.After installation, the icon will be found in ”Start”→“Devices and Printers”. Note: 1.If you have already installed the driver (No matter what kind of ports), it will generate a USB port automatically when connecting the printer to computer.
PR-600 Series HPRT-HT100 User Manual 7.4 Usage 7.4.1 Printing Preferences 1.Click “Start”→“Devices and Printers”. Right click the icon and choose “Printing preferences”. Rev.1.0...
Page 46
PR-600 Series HPRT-HT100 User Manual 2.According to different needs, set up the page. Rev.1.0...
Page 47
PR-600 Series HPRT-HT100 User Manual ●Click “Stock”→”Name”, and choose the paper type. ●Click “New Stock”, and set up a new stock. Rev.1.0...
Page 48
PR-600 Series HPRT-HT100 User Manual ●Click “Edit Stock”, and edit the stock. ●Click “Delete Stock”, and delete the stock. Rev.1.0...
Page 49
PR-600 Series HPRT-HT100 User Manual ●Choose “Orientation” or “Effects”, showed in the “Preview”. Rev.1.0...
Page 50
PR-600 Series HPRT-HT100 User Manual ●Click “Preset”→“Name”, and back to the default settings. ●Click “Manage”, and change the settings. Rev.1.0...
Page 51
PR-600 Series HPRT-HT100 User Manual 3.Click “Graphics”, and edit the pictures. 4.Click “Stock”. Rev.1.0...
Page 52
PR-600 Series HPRT-HT100 User Manual ●Click “Method”, and choose the printing method. ●Click “Type”, and choose the printing type. Rev.1.0...
Page 53
PR-600 Series HPRT-HT100 User Manual ●Click “Post-Print Action”, and choose the method of media handling. Rev.1.0...
Page 54
PR-600 Series HPRT-HT100 User Manual 7.4.2 Printer Properties 1.Click “Start”→“Devices and Printers”. Right click the icon and choose “Printer properties”. Rev.1.0...
Page 55
PR-600 Series HPRT-HT100 User Manual 2.Click “General”→“Print Test Page”, and printer will print labels with current settings. Rev.1.0...
Page 56
PR-600 Series HPRT-HT100 User Manual 3.Click “Ports”, then choose the port needed. 7.4.3 Label’s Width USER(4.00 in×4.00 in) 2×4(2.00 in×4.00 in) 4×4(4.00 in×4.00 in) 4×6(4.00 in×6.00 in) Rev.1.0...
PR-600 Series HPRT-HT100 User Manual 7.5 Removing Note: Please turn off the printer or unplug the USB cable before removing the driver. 1.Double click Seagull Windows Driver 2.Read and agree the license agreement. Then click “Next”. Rev.1.0...
Page 58
PR-600 Series HPRT-HT100 User Manual 3.Choose the installation directory, then click “Next”. 4.Click"Finish". Rev.1.0...
Page 59
PR-600 Series HPRT-HT100 User Manual 5.Select “Remove printer drivers”, then click “Next”. 6.Select “Remove printers”, then click “Next”. Rev.1.0...
Page 60
PR-600 Series HPRT-HT100 User Manual 7.Select printer’s name, then click “Next”. 8.Please unplug the USB cable or turn off the printer when appearing the following prompt. Rev.1.0...
Page 61
PR-600 Series HPRT-HT100 User Manual 9.Click “Finish”. 10.Restart the computer when appearing the following prompt or continue step 11. Rev.1.0...
Page 62
PR-600 Series HPRT-HT100 User Manual 11.Click “Close”. The driver has been removed successfully. Rev.1.0...
PR-600 Series HPRT-HT100 User Manual Chapter 8 BarTender Ultralite Instructions 8.1 Introduction This chapter provides instructions on BarTender Ultralite program according to PC operating systems(OS). The followings are supported. Microsoft Windows 10 (32 bit/64 bit) Microsoft Windows 8 (32 bit/64 bit)
PR-600 Series HPRT-HT100 User Manual 8.3 Installation Note : Under different operating systems, the screen may be slightly different. Take Windows 7 as example. Take printer HT100 as example. Please refer to printer HT100 when using printer HT130.
Page 65
PR-600 Series HPRT-HT100 User Manual 4.Click “Next”. 5.Read and accept the license agreement, then click "Next". Rev.1.0...
Page 66
PR-600 Series HPRT-HT100 User Manual 6.Select "Features" and installation location, then click "Next". 7.Click "Install". Rev.1.0...
Page 67
PR-600 Series HPRT-HT100 User Manual 8.Click "Finish". 9.Back to desktop, and you will see the icon of BarTender Ultralite. Double click it and get down to use. Rev.1.0...
PR-600 Series HPRT-HT100 User Manual 8.4 Usage 8.4.1 Page Settings 1.Double click the icon, then choose the edition. Click “OK”. (The edition may be changed according to different needs.) 2.Click “Start a new BarTender document”. Rev.1.0...
Page 69
PR-600 Series HPRT-HT100 User Manual 3.Choose “Blank Template”, then click “Next”. 4.If the predefined stocks don’t meet your need, tick “Specify Custom Settings”. Then click”Next”. Rev.1.0...
Page 70
PR-600 Series HPRT-HT100 User Manual 5.Tick “Single item per page”, then click “Next”. (If you print multiple labels, tick “Multiple columns and/or rows of items per page ”.) 6.Edit the side edges, then click “Next”. Rev.1.0...
Page 71
PR-600 Series HPRT-HT100 User Manual 7.Choose the item shape, then click “Next”. 8.Edit the template size, then click “Next”. Rev.1.0...
Page 72
PR-600 Series HPRT-HT100 User Manual 9.Based on your need, edit the template background. Then click ”Next”. 10.Finish the settings, showed in the “Review” and “Preview”. Then click “Finish”. Rev.1.0...
Page 73
PR-600 Series HPRT-HT100 User Manual 8.4.2 label Edit 1.Click the icon of code 2.Choose the code, then click “Select”. 3.Click the blank, showing the code. Rev.1.0...
Page 74
PR-600 Series HPRT-HT100 User Manual 4.Double click the code and edit it. User can set up the size, font, border and so on. Finishing the changes, click “Close”. 5.Click the icon of character , then enter the text. Rev.1.0...
Page 75
PR-600 Series HPRT-HT100 User Manual 6.Click the icon of picture , then edit the pictures. 7.Compose the text. 8.Finish all the settings. Click “Print” and a new label will be printed. Rev.1.0...