Panasonic WH-ADC0309H3E5 Service Manual page 37

(Ancho

After sele ecting the bes
1 Fix th he unit on con
2 When n installing at
firmly y with bolt or
1 11.2.2.2 Disposal

When a D Drain elbow i
the un nit should be
o
cover r the ø20mm
o
use a a tray (field su
o

If the unit is used in a
not to use e the Drain e
2
Rubb ber cap
UD0
1 1.2.3 Co nnecting t
1 11.2.3.1 Connectin
D Decide piping g length and
R Remove burrs s from cut ed
in nserting the f flare nut (loca
p ipe. Align ce enter of piping
w with torque w rench to the
th he table.
Model
UD03*E5* an nd ø12.7
UD05*E5*
UD07*E5* an nd ø15.88
UD09*E5*
C Close the tube e joining are
(l ocal supply) without any
(T To prevent in nsects or sm
(F For UD07*E5 5* and UD09
11.2.3.1.1 1 Cutting
1 Pleas se cut using p
2 Remo ove the burrs
Turn t the piping en
3 Pleas se make flare
Pipe
Ream
Po oint
do wn
1. . To cut 2. To remove bu
E
A A B
or pitch)
st location, s start installati
ncrete or rigi d frame firm
t roof, please e consider st
nails.
of Outdoo or Unit Dra
s used, plea se ensure to
e placed on a a stand which
holes with R Rubber cap (
upply) when necessary to
n area where e temperatur
elbow and Ru ubber cap, fo
Drain el
x 7
03*E5* and UD0 05*E5*
the Piping g
ng the Pip ping to Ou
then cut by u using pipe cu
dge. Make fla are after
ate at valve) onto the cop
g to valves a and then tigh
specified tor rque as state
Piping size (Torque)
Gas Liquid
7mm (1/2") ø6.35mm (1/4
[55 5 N•m] [18 N•m]
8mm (5/8") ø6.35mm (1/4
[65 5 N•m] [18 N•m]
a with putty heat insulato
gap as show wn in right fig
all animal en ntering.)
9*E5* only)
g and Fla ring the P
pipe cutter a nd then remo
s by using re amer. If burr
nd down to a avoid the met
e after inserti ing the flare
Han ndle
er
Bar
Yoke
Core
Clamp
Re ed arrow mark
handle
rrs 3. To fla are
Model
UD03*E5* a
UD05*E5
UD07*E5* a
UD09*E5
on according g to Installati
ly and horizo ontally by bo
trong wind an nd earthquak
ain Water
o follow below w:
h is taller tha an 50 mm.
(refer to illust tration below
o dispose the e outdoor un
re falls below w 0°C for 2 o
or the drain w water freezes
lbow 1
Rubber
utdoor Uni it
utter.
pper
ten
ed in
Be sure to u
(If the nuts a
to break or
4")
4")
or
gure.
Piping
ove the burrs s.
rs is not remo oved, gas lea
tal powder e ntering the p
nut onto the copper pipe
 Impro
0 – 0.5 mm
Ba r
Inclined Surfac
Copper pipe
damage
A B C
and
540 160 20
*
and
620 140 15
*
on Diagram. .
lt nut (ø10 m mm).
ke. Please fa asten the inst
w).
nit drain wate er.
r 3 consecut tive days, it is
s and the fan n will not rota
2
cap
x 8
UD07*E5* an nd UD09*E5*
Spanner S
or Wrench o
use two span nners to tight
are overtight tened, it may
leak.)
Putty or Hea
insulator
(local supply
akage may b be caused.
pipe.
s.
per flaring 
When prope
surface of th
and be of ev
flare part com
ce Uneven n
Cracked
the connect
ed thicknes s
the flare finis
D E F
330 430 46
355 450 44
(Un nit : mm)
tallation stan nd
s recommen ded
ate.
1
Dra ain elbow
Torque
wrench
ten.
y cause the f flares
at
y)
erly flared, the int ternal
he flare will even ly shine
ven thickness. S ince the
mes into contact t with
tions, carefully check
sh.