Panasonic WH-ADC0309H3E5 Service Manual page 32

11.1.4.2 1 Wire Strip
No l
whe
11.1.4.3 1 Connectin
For Tank Unit F t with UD03H

The equip pment's Pow

The equip pment's Pow
network.

The equip pment's Pow

The equip pment's Pow
network, w with the follo
Please lia aise with sup
impedanc ce or less.
For Tank Unit F t with UD07H

This equip pment's Pow
greater th han or equal
responsib bility of the in
operator i if necessary,
or equal t to 400.00kW

The equip pment's Pow
network, h having servic
current ca apacity at the

The equip pment's Pow

The equip pment's Pow
network, w with the follo
Please lia aise with sup
impedanc ce or less.
1 1.1.5 Ch arging an
Wa ater

Make sur e all the pipi
done befo ore carry out
1 11.1.5.1 Charge th

For Dom estic Hot W
1 Set th he Domestic
(Drain n Tap) to "
C " L O S " E
D omestic Hot Wat
2 Set a ll Tap / Show
3 Start filling water t
Tank via Tube Co
After 20~40min, w
Tap / Shower. Els
autho orized dealer
4 Chec k and make
tube c connecting p
pping and Connecti
W ire stripping
Indoor/outdoor
connecting
terminal board
5mm or
more
oose strand
(gap between
n insert
wires)
ng Requir rement
HE5-1/UD05 HE5-1
wer Supply 1 complies wit
wer Supply 1 complies wit
wer Supply 2 complies wit
wer Supply 2 complies wit
owing maxim um permissi
pply authority y to ensure th
HE5-1/UD09 HE5-1
wer Supply 1 complies wi
to 400.00kW W at the interf
nstaller or use er of the equ
, that the equ uipment is co
.
wer Supply 1 complies wit
ces current c capacity ≥ 10
e interface po oint is sufficie
wer Supply 2 complies wit
wer Supply 2 complies wit
owing maxim um permissi
pply authority y to ensure th
d Dischar rging the
ng installatio ons are prope
t below steps s.
he Water
Water Tank
Hot Water T Tank Dischar
"CLOSE".
" O P E " N
ter Tank Discharg ge (Drain Tap)
wer "OPEN".
to the Dome stic Hot Wat
onnector i.
water should flow out from
se, please co ontact your lo
r.
sure no wate er leaking at
points.
ing Requir rement
Conductor
fully insert
ACCEPT
th IEC/EN 61 1000-3-2.
th IEC/EN 61 1000-3-3 and
th IEC/EN 61 1000-3-2.
th IEC/EN 61 1000- 3-11 a
ble system i mpedance Z
hat the Powe er Supply 2 is
th IEC61000 0-3-12 provid
face point be etween the u
uipment to en nsure, by con
onnected onl y to a supply
th IEC/EN 61 1000-3-11 an
00A per phas se. Please lia
ent for the in nstallation of
th IEC/EN 61 1000-3-2.
th IEC/EN 61 1000-3-11 an
ble system i mpedance Z
hat the Powe er Supply 2 is
5 Set
(Dra
rele
erly
The
6 Tur
cou
sec
The
7 Ens
rge
afte
Tan
8 To
the
Rel

For Spa
1 Tur
g g
anti
clos
ter
m
ocal
the
Conductor Co nductor not
over insert fu ully insert
PROHIBITED P PR ROHIBITED
d can be con nnected to cu
nd shall be c connected to
Z = 0.445 o ohm (Ω) at th
max
s connected only to a sup
ded that the s short circuit p
ser's supply and the pub
nsultation wit th the distrib
y with a shor rt circuit pow
nd shall be c connected to
aise with sup pply authority
the equipme ent.
nd shall be c connected to
Z = 0.445 o ohm (Ω) at th
max
s connected only to a sup
the Domest tic Hot Water
ain Tap) to o "OPEN" for
ease air from m this pipeline
en set it "CLO OSE".
n the Safety Relief Valve
unterclockwis se slightly an
conds to relea ase air from
en recover th he knob to or
sure Step 5 & & 6 is carried
er charging w water to Dom
nk.
prevent back k pressure fr
Safety Relie ef Valve, do t
ief Valve kno ob counterclo
ace Heating g / Cooling
n the plug on n the Air Pur
iclockwise by y one comple
sed position.
Plug (tur
anticlock
one com
urge valve a
Air p
urrent supply y
o suitable sup pply
he interface.
pply of that
power S is
sc
blic system. I t is the
ution networ rk
er S greate er than
sc
a suitable su upply
y that the ser rvice
suitable sup pply
he interface.
pply of that
r Tank Disch arge
r 10 seconds s to
e.
e knob
nd hold for 10 0
this pipeline .
riginal positio on.
d out each tim me
mestic Hot Wa ater
om happenin ng to
turn the Safe ety
ockwise.
rge Valve out tlet
ete turn from m fully
n
kwise by
plete turn)