1. Manuals
  2. Brands
  3. KLIK Manuals
  4. Switch
  5. Pixmob HUB2
  6. User manual

KLIK Pixmob HUB2 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DATASHEET-USER
GUIDE HUB2
Version 1.3, 02-01-2020

Advertisement

Table of Contents
loading

Related Manuals for KLIK Pixmob HUB2

Summary of Contents for KLIK Pixmob HUB2

  • Page 1 DATASHEET-USER GUIDE HUB2 Version 1.3, 02-01-2020...

  • Page 2: Table Of Contents

    103 rue Louvain Ouest, H2N 1A3, Montreal Contents HUB2 presentation and characteristics ..................3 1.1 Description use ........................... 3 1.2 Electrical charateristics ........................3 1.2.1 Description ........................... 3 1.2.2 Key features ..........................3 1.2.3 Working temperature ........................3 1.2.4 Water/Dust protection ......................... 3 1.2.5 Physical and body .........................

  • Page 3: Hub2 Presentation And Characteristics

    1.1 Description use The Pixmob HUB2 is an improvement from the last version of the HUB. It doesn’t need anymore a hard line wire for ethernet either an AC plug, smartphone as screen, battery powered, etc. The HUB2 can be place in hard access position and with the integrated battery, it will last around a half of the day if it always used.

  • Page 4: Electrical Specs

    103 rue Louvain Ouest, H2N 1A3, Montreal 1.2.6 Electrical specs FREQUENCY BAND: 2400–2483.5 MHz RF POWER MAX(W): Conducted 115mW TYPE OF MODULATION: GFSK POWER REQUIREMENTS: USB 5V with a battery 3.7V 5000mAh inside MAXIMUM TRANS DUTY CYCLE: 10% of duty cycle ANTENNAS INFORMATION: Bluetooth antenna RPSMA, 2.4 GHz Gain 4.9 dBi.

  • Page 5: Fcc Statements

    103 rue Louvain Ouest, H2N 1A3, Montreal 2. FCC Statements FCC ID: 2ADS4HUB2 § 15.19 (a)(3) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  • Page 6: Ic Statements

    103 rue Louvain Ouest, H2N 1A3, Montreal 3. IC Statements IC: 7254A-HUB2 This device complies with Industry Canada license-exempt RSS 247 standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

  • Page 7: Warning

    5. Material needed -1 USB-B cable to USB-A (Power and recharge the HUB2) -1 USB-A cable to USB micro (Communicate and recharge the Phone -1 antenna 2.4 GHz -1 phone with the Klik app USER GUIDE HUB2 | VERSION 1.3...

  • Page 8: Installation

    103 rue Louvain Ouest, H2N 1A3, Montreal 6. Installation 6.1 Installation The HUB2 might be install near a wall or an AC outlet for big event. The battery can run less than a day without charging (depending on the usage of these). The HUB2 also need to be out of sight of people and not in a restricted place to be sure that the data is correctly send to the server.

  • Page 9: Hub2 Button Control And Light

    7.1 Home screen When the HUB2 is open (switch in UP position), it will automatically open the phone and the Klik app. You will need after to setup the WIFI configuration and some parameter to be sure that the HUB2 is connected to the good server.

  • Page 10: Troubleshooting

    -Phone is "stuck" in kiosk mode? Follow procedure in the link on the right 8.3 PHONE (HUBDROID) software update Some apps (chrome, hexnode, ...) keep auto updating, killing the focus of Klik app...? No solution for the moment. 8.4 IP NETWORKING...

Table of Contents