Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Dream Bot L10 Pro
Summary of Contents for Dream Bot L10 Pro
- Page 1 Dreame L10 Pro Robot Vacuum...
- Page 2 One. General * What’s the function of the line laser? How do I use it? A: The line laser on the robot vacuum helps recognize its surroundings and obstacles, which then enables the vacuum to accurately avoid bumping and reduce the probability of entanglement, stuck and accidentally riding on small objects.
- Page 3 Orange Fast Flashes: error Tip: The robot vacuum cannot be turned off during charging; Press any button to pause in the middle of cleaning, Spot Clean, or charging. 2. What is the (Dock) button on the vacuum cleaner for, and how do I use it? A：please refer to the table below Function...
- Page 4 4. How to reset Wi-Fi with Dreame L10Pro robot? A：When your phone fails to connect with the robot due to router configuration changes, forgetting password or other reasons, open the top cover and observe the Wi-Fi indicator LED. Press and hold the Spot Clean button and Dock button until hearing a voice prompts of "waiting for network configuration".
- Page 5 where the robot will clean a square area with a side length of 1.5 meters centered on itself. After cleaning is finished, robot will automatically return to the starting position and stop working. 6.How to use the Do-Not-Disturb mode with Dreame L10Pro robot? A：DND mode is enabled by default from 22:00 pm to 08:00 am, you can disable or edit DND mode with Mi Home app.
- Page 6 9. How to use the Advanced Map function on the robot vacuum? A: Launch the Mi Home app, tap to start cleaning, and D9 will automatically learn about the surroundings and start building a full map, where you can access to Auto Zone, Area Editor, Zoned Cleanup, Designated Cleanup, Virtual Wall, and other functions.
- Page 7 12. Can Dreame L10Pro robot connect to the dock all the time? Is there an overcharge protection? A ：Yes. The robot supports overcharging protection, and will disconnect automatically once fully charged. 13. What is the size of Dreame L10Pro? A：The dimensions of Dreame L10Pro is 350*350*96.8 mm, with a height of 9.68 cm. 14.
- Page 8 17. Does Dreame L10Pro have a motor overload protection? A：Yes. Dreame L10Pro has overload protection for all motors on-board, including the suction module, main brush, side brush, and main driving wheel. Motor overload protection is on once the robot is severely clogged with debris or foreign matters. 18.
- Page 9 a better app control experience, make sure the dock is connected to Wi-Fi. Note: Do not place the dock in direct sunlight or block the identification area with any objects, otherwise the robot may fail to return automatically. 2. How to charge Dreame L10Pro? A：Press the power button and hold.
- Page 10 （1）Install the mop: Wet the mop pad and wring it out until it stops dripping, insert it all the way along the slots of the water tank, and stick it firmly. （2）Fill the water tank: Open the cover of the water tank, fill with water and close the cover.
- Page 11 Notes: Do not use the mop mode when no one is at home; Do not mop on carpets; Please use detergent carefully as it may clog the filter of the water tank. When charging or not in use, please remove the mop module, pour the remaining water and clean the mop to avoid mold or odor.
- Page 12 6. How does Dreame L10Pro return to dock for charging? A：After cleaning, L10Pro will automatically return to the dock for charging， in pause status, press the dock button for charging, the buttons will flash slowly when charging. Power ≤ 15% is indicated by orange flashes, power > 15% is indicated by white flashes.
- Page 13 8. How to clean the dust bin and filter of Dreame L10Pro? A： （1）Open the upper cover of the robot, press the buckle to remove the dust bin; （2）Open the bin cover marked with the arrow and remove the debris inside; （3）Fill the dust bin with water, close the cover, shake the bin left and right, pour out, and repeat for several times;...
- Page 14 Note: Wash the bin with water only. Do not add any detergent or clean the filter screen with finger or brush. （4）Remove the filter screen as illustrated, spin off the water, dry the filter before installing it back to the bin for use. Note: Ensure the filter is dried up (for at least 24 hours) before use 9.
- Page 15 10. How to clean the side brush of Dreame L10Pro? A： 1. Turn over the robot, pull out the side brush and clean it up as shown below. 2. Re-install the side brush. Tip: It is recommended to clean the side brush once a month and replace every 3-6 months for a better cleaning result.
- Page 16 12. How to clean and maintain the robot vacuum? A：Use soft dry cloth to wipe the parts, which includes: 1. Four cliff sensors at the bottom 2. The infrared deceleration sensor in the front 3. The electric pole at the bottom 4.
- Page 17 15. How to restore to factory settings with Dreame L10Pro? A：If L10Pro still fails to operate normally after restarting, press and hold the reset button with a tool until hearing the voice prompt "start to restore factory settings". Four. *New line laser related questions 1.
- Page 18 2. What should I do if the robot vacuum fails to avoid obstacles during the cleaning? A ： 1. The sensor might be clouded by dirt. Wipe the obstacle sensor in the middle of the bumper with a soft dry cloth and try restart the machine to check if it can work properly. 2.
- Page 19 2. *Black carpet, sliding door track, staircase suspending warnings A : There are 6 sets of downward infrared sensors equipped in front of the universal wheels and on the side of the driving wheels. When the sensors detect stairs that are wider than 85mm, it will retreat to avoid falling.
- Page 20 for connection result after hearing the voice report. Ensure the location permission of the app has been enabled before network connection. Failure to enable the permission will result connection failure. If the network still fails, please try to restart the host and router. 4.
- Page 21 8. Why do I smell odor from the mop and dust compartment? Odor is caused by dirty mop that is not washed in time after cleaning. Please clean the rag in time after mopping the floor. The dust compartment may also emit odor with liquid getting inside. Please clean the dust compartment in time after cleaning.
- Page 22 drop quickly in the first few minutes during cleaning. After this, the power consumption will return to normal. Battery will also drop faster in Turbo mode. 13. What should I do if the L10Pro is entangled with the power cord of the dock during cleaning？ Tie the excessive power cord of the dock with a strap before cleaning.
- Page 23 2. The map in the APP disappear when the sweeping begins(and the orientation fails too), what should I do then? A :It may be caused by placing it in places where has not been swept, please move it to places where it had been swept earlier.
- Page 24 map next time while it enters the space. 3. Please do not follow or let your pet follow the robot vacuum while it is working since it will affect its mapping and obstacle avoiding accuracy. 4. To ensure the cleaning coverage, the robot vacuum will clean each section including all the corners.
- Page 25 1. Please make sure if the robot vacuum is working in Zoned Cleanup mode. If it is, please move any obstacle that is on the way of the vacuum moving to the designated area. 2. Please remove any obstacle on the way or open the door for the robot vacuum in order for it to clean properly.
- Page 26 while it is working, the machine will reroute to avoid bumping. 2. Staircase obstacle avoidance: If the robot vacuum encounters high staircase, vertical gaps or tracks of slide door, its route may be disordered. We recommend building a slope for the robot vacuum or setting virtual walls in such situations.
- Page 27 9. What are the possible reasons for failing to return to the charging base to recharge? 1. There are too many obstacles next to the charging base. Please place the charging base in an open space and make sure there are at least 0.5m empty space on both sides of the base and 1.5m clear space in front of the base.
- Page 28 uncleaned one, but it is not repeating the work. 13. How to deal with device errors of Dreame L10Pro? A : Press the Power/Clean button and hold for 6 seconds to restart. 14. Why is the scheduled clean not working? A: It might be caused by low battery level.
- Page 29 Eight. Common hardware problems 1. Why does the robot vacuum still tangle hairs? A: The robot vacuum is equipped with a row of combing gears that helps reduce hair entanglement and lower maintenance frequency. However, for heavy tasks where a lot of hair is involved, the robot vacuum might still get tangled and need to be cleaned manually.
- Page 30 radar on top of the robot vacuum. If so, please remove the foreign object. 4. *Why does the robot vacuum indicate LDS laser sensor malfunction A： 1. Please check if the hardware version is updated to the latest version. If not, update the hardware and operate the robot vacuum again to see if the problem is solved.
- Page 31 robot vacuum loud, please try the following options: adjust to quiet cleaning mode via the APP or schedule clean in the period when the house is empty. 7. What should I do if the robot vacuum makes abnormal noise while cleaning? 1.
- Page 32 Users can adjust the water level based on the types of cleaning. If the water level is at its maximum, water stains might be left on the floor. 10. What should I do if the L10Pro fails to charge? Please clean the charging interface of the dock and the robot if there is any dust on it, as dust may result in charging failure.
- Page 33 14. *What should I do if the water tank falls while working? :If the water tank is not installed properly, it might fall while working. Make sure you hear a sound of click on both sides of the water tank while installing it to the robot vacuum. A successfully installed water tank couldn’t be pulled off by hand.
Need help?
Do you have a question about the Bot L10 Pro and is the answer not in the manual?
Questions and answers