Page 2: Table Of Contents
The 2003 GMC Envoy/Envoy XL Owner Manual Preface Seats and Restraint Systems ... Front Seats Rear Seats Safety Belts Child Restraints Air Bag Systems Restraint System Check Features and Controls ... Keys Doors and Locks Windows Theft-Deterrent Systems Starting and Operating Your Vehicle...
Page 3 We reserve the right to make changes after that time without further notice. For vehicles first sold in Canada, substitute the name “General Motors of Canada Limited” for GMC whenever it appears in this manual. Please keep this manual in your vehicle, so it will be there if you ever need it when you’re on the road.
Page 4 Safety Warnings and Symbols You will find a number of safety cautions in this book. We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning. These mean there is something that could you or other people.
Page 5 Vehicle Damage Warnings Also, in this book you will find these notices: Notice: These mean there is something that could damage your vehicle. A notice will tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly.
Page 6 These are some examples of vehicle symbols you may find on your vehicle: LATCH BOTH LAP AND CAUTION SHOULDER BELTS TO POSSIBLE PROTECT OCCUPANT INJURY DO NOT TWIST SAFETY BELT WHEN ATTACHING PROTECT EYES BY FASTEN SHIELDING SEAT BELTS \& CAUSTIC &...
Page 7 NOTES...
Page 8: Seats And Restraint Systems
Section Front Seats ... Power Seats ... Power Lumbar Heated Seats ... Power Reclining Seatbacks ... Head Restraints ... Rear Seats ... 1-6 Rear Seat Operation ... Safety Belts ... Safety Belts: They Are for Everyone ... 1-9 Questions and Answers About Safety Belts ... 1-13 How to Wear Safety Belts Properly ...
Page 9: Front Seats
Front Seats Power Seats Your vehicle may have this feature. The power seat controls are located on the outboard side of the front seat cushions. The horizontal control adjusts the seat cushion and the vertical control adjusts the seatback. Move the front of the seat control up or down to adjust the front portion of the cushion.
Page 10 Heated Seats Your vehicle may have heated front seats. The buttons used to control this feature are located on the front door armrests. The engine must be running for the heated seat feature to work. To heat the entire seat, press the horizontal button with the heated seat symbol.
Page 11 Power Reclining Seatbacks The vertical power seat control described earlier allows the seatback to recline. But don’t have a seatback reclined if moving. 1 -4 Sitting in a reclined position whel. ;our vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this.
Page 12 Head Restraints Adjust your head restraint so that the top of the restraint is closest to the top of your head. This position reduces the chance of a neck injury in a crash. 1 -5...
Page 13: Rear Seats
Rear Seats Rear Seat Operation Your vehicle may have a folding rear seat which lets you fold the seatbacks down for more cargo space. Pull up on the loop located where the seat cushion meets the seatback to fold the seat cushion up and out of the way.
Page 14 To return the head restraint to the upright position, reach behind the seat and pull the restraint up until it locks into place. Push and pull on the head restraint to make sure that it is latched securely. Rear Seats (Envoy XL) The second row seat is a 65/35 split seat which may be folded and tumbled.
Page 15 Returning the Seats to an Upright Position To return the seat@) to the upright position, do the following: 1. Return the seat to the floor pins by rotating the seat down to reengage the seat hooks. 2. Try to raise the seat to check that it is locked down. 3.
Page 16: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. ’ C - - I t let -.le ride where he --.., wear a safety belt properly.
Page 17 You never know if you’ll be in a crash. If you do have a crash, you don’t know if it will be a bad one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person wouldn’t survive. most crashes are in between.
Page 18 Get it up to speed. Then stop the vehicle. Put someone on it. The rider doesn't stop. 1-1 1...
Page 20 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That’s why safety belts make such good sense. Questions and Answers About Safety Belts Won’t I be trapped in the vehicle after an...
Page 21 If I’m a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you’re in an accident even one that isn’t your fault your passengers can be hurt. Being a good driver doesn’t protect you from things beyond your control, such as bad drivers.
Page 22 Lap-Shoulder Belt The driver has a lap-shoulder belt. Here’s how to wear it properly. 1. Close and lock the door. 2. Adjust the seat so you can sit up straight. To see how, see “Seats” in the Index. 3. Pick up the latch plate and pull the belt across you. Don’t let it get twisted.
Page 23 5. To make the lap part tight, pull up on The lap part of the belt should be worn low and snug on the shoulder belt. the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt.
Page 24 What’s wrong with this? The shoulder belt is too loose. as much protection this way. You can be seriously hurt if ,Jur shoulder belt too loose. In forward too much, which could increase injury. The shoulder belt should fit against your body. give won’t nearly...
Page 25 What’s wrong with this? The belt is buckled in the wrong place. 1-18 Yo, can be s e r L s l y injured jour belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 26 What's wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 27 What's wrong with this? across The belt is twisted the body. 1-20 Yo-. :an be s-..ously injured by a In a crash, you wouldn't have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it.
Page 28 To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. if you slam the door on it, you can damage both the belt and your vehicle.
Page 29 Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they don’t wear safety belts. 1-22 A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
Page 30 Rear Seat Passengers It’s very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash.
Page 31 Lap-Shoulder Belt All rear seating positions have lap-shoulder belts. Here’s how to wear one properly. 1. Pick up the latch plate and pull the belt across you. Don’t let it get twisted. 2. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure.
Page 32 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash this applies force to the strong pelvic bones. And you'd be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 33 To unlatch the belt, just push the button on the buckle. 1-26 Rear Safety Belt Comfort Guides for Children and Small Adults Your vehicle may already have this feature. If not, you can get it from your GM dealer. Rear shoulder belt comfort guides provide added safety belt comfort for older children who have outgrown booster seats and for small adults.
Page 35 4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-23. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides.
Page 36 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. 4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-23. Make sure that the shoulder belt crosses the shoulder.
Page 37: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. 1-30 What is the proper way to wear safety belts? possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 38 Never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck?
Page 39 Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 40 Every time infants and young children ride in vehicles, they should have the protection provided by appropriate restraints. Young children should not use the vehicle’s adult safety belts alone, unless there is no other choice. instead, they need to use a child restraint. People should never hold a baby in their arms while riding in a vehicle.
Page 41 1-34 Children who are u- against, or very close to, any air bag when it inflates can be seriously injured or killed. Air bags plus lap-shoulder belts offer outstanding protection for adults and older children, but not for young children and infants.
Page 42 For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards.
Page 43 Child Restraint Systems An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous flat surface. Make sure that the infant’s head rests toward the center of the vehicle.
Page 44 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. A booster seat (F-G) is a child restraint designed to improve the fit of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a five-point harness.
Page 45 How do child restraints work? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner.
Page 46 Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We, therefore, recommend that child restraints be secured in a rear outside seat position including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat.
Page 47 Top Strap Some child restraints have a top strap, or “top tether.” It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
Page 48 Anchor the top strap to one of the following anchor points. Be sure to use an anchor point located on the same side of the vehicle as the seating position where the child restraint will be placed. Raise the head restraint and route the top strap Resfraints on under it.
Page 49 Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle may have the LATCH system. If it does, you’ll find anchors (A) in the rear outside seat positions. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system will have two metal tabs where the seat cushion meets the seatback.
Page 50 With this system, use the LATCH system instead of the vehicle’s safety belts to secure a child restraint. See Securing a Child Restraint in a Rear Outside Seat Position on page 1-44. If a -.4TC --type child restraint isn’t attached to its anchorage points, the restraint won’t be able to protect the child correctly.
Page 51 Securing a Child Restraint Designed for the LATCH System Find the anchors for the seating position you want to use, where the bottom of the seatback meets the back the seat cushion. Put the child restraint on the seat. Attach the anchor points on the child restraint to the anchors in the vehicle.
Page 52 You’ll be using the lap-shoulder belt. See Top Strap if the child restraint has one. Be sure to page 7-40 follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say. 1.
Page 53 1 -46 5. To tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint. If you’re using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 54 Securing a Child Restraint in the Right Front Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-42. Your vehicle has a right front passenger air bag. Never put a rear facing child restraint in this seat.
Page 55 Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. 4. Buckle the belt. Make sure the release button positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Page 56 6. To tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint. You may find it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 57: Air Bag Systems
Systems Air Bag This part explains the frontal and side impact air bag systems. Your vehicle has air bags a frontal air bag for the driver and another frontal air bag for the right front passenger. Your vehicle may also have a side impact air bag.
Page 58 Here are the most important things to know about the air bag systems: 1 3 1 1 You can be severe !ly injured or killed in a crash if you aren’t wearing your safety belt you have air bags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it.
Page 59 CAUTION: (Contirluea during a crash. Always belt, even with frontal air Dags. The driver should sit as far back as possible while still maintaining control of the vehicle. Front occupants should not lean on or sleep against the door. Anyone who is up against, or very close to, any air bag when it inflates can be seriously injured or killed.
Page 60 Where Are the Air Bags? The right front passenger's frontal air bag is in the instrument panel on the passenger's side. The driver's frontal air bag is in the middle of the steering wheel. 1-53...
Page 62 If something is between an occupant and an air bag, the bag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating air bag must be kept clear. Don’t put anything between an occupant and an air bag, and don’t attach or put anything on the steering wheel hub or on or near any other air...
Page 63 In any particular crash, no one can say whether an air bag should have inflated simply because of the damage to a vehicle or because of what the repair costs were. For frontal air bags, inflation is determined by the angle of the impact and how quickly the vehicle slows down in frontal and near-frontal impacts.
Page 64 What Will You See After an Air Bag Inflates? After the air bag inflates, it quickly deflates, so quickly that some people may not even realize the air bag inflated. Some components of the air bag module will be hot for a short time. These components include the steering wheel hub for the driver’s frontal air bag and the instrument panel for the right front passenger’s frontal air bag.
Page 65 In many crashes severe enough to inflate an air bag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger air bag. Air bags are designed to inflate only once. After an air bag inflates, you’ll need some new parts for your air bag system.
Page 66 Servicing Your Air Bag-Equipped Vehicle Air bags affect how your vehicle should be serviced. There are parts of the air bag systems in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the air bag systems.
Page 67: Restraint System Check
Restraint System Check Checking Your Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 68 Replacing Restraint System Parts Aft- a Crash A crash can damage the restraint system! your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 69 NOTES 1-62...
Page 70: Features And Controls
Section 2 Keys Remote Keyless Entry System ... Remote Keyless Entry System Operation Doors and Locks ... Door Locks ... Power Door Locks ... Delayed Locking ... 2-9 Programmable Automatic Door Locks ... 2-10 Rear Door Security Locks ... Lockout Protection ... Leaving Your Vehicle ...
Page 71 Section 2 HomeLin k@ Transmitter ... Programming the HomeLink@ Transmitter ... 2.42 Storage Areas ... Glove Box ... 2.46 Overhead Console Front Storage Area Luggage Carrier ... Features and Controls 2.42 Rear Floor Storage Lid ... Convenience Cover 2.46 Cargo Sunroof ...
Page 72: Keys
Keys Leaving -.lildren in a vehicle with the ignition key is dangerous for many reasons. A child others could be badly injured even killed. They could operate the power windows or other controls even make the vehicle move. Don’t leave the keys in a vehicle with children.
Page 73 This vehicle has one double-sided key for the ignition and door locks. It will fit with either side up. When a new vehicle is delivered, the dealer provides the owner with a pair of identical keys and a key code number. The key code number tells your dealer or a qualified locksmith how to make extra keys.
Page 74 Remote Keyless Entry System Your keyless entry system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 75 Remote Keyless Entry System Operation If your vehicle has this feature, you can lock and unlock your doors from about 3 feet m) up to 30 feet (9 m) away using the remote keyless entry transmitter supplied with your vehicle. You can program different feedback settings through the Driver Information Center (DIC).
Page 76 Battery Replacement touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter. To replace the battery in the remote keyless entry transmitter do the following: . , , Insert a thin coin in the slot between the covers of the transmitter housing.
Page 77: Doors And Locks
Doors and Locks Door Locks -docked doors can ..mgerous. ~- - Passengers especially children easily open the doors and fall out of a moving vehicle. When a door is locked, the handle won’t open it. You increase the chance of being thrown out of the vehicle in a crash if the doors aren’t locked.
Page 78 Power Door Locks The power door lock switches are located on the driver’s and front passenger’s armrests. Remove the ignition key and press the lock symbol to lock all of the doors at once. To unlock the doors, press the other side of the switch. Delayed Locking This feature makes it easier to use the power door locks to lock all the doors and the liftgate when leaving your...
Page 79 Programmable Automatic Door Locks Your vehicle is equipped with an automatic IocWunlock feature which enables you to program your vehicle’s power door locks. You can program this feature through the Driver Information Center (DIC), or by the following method. Programmable Locking Feature The following is the list of available programming options: Mode 1: All doors lock when the transmission is shifted...
Page 80 Programmable Unlocking Feature The following is the list of available programming options: Mode 1: Driver’s door unlocks when the transmission is shifted into PARK (P). Mode 2: All doors unlock when the transmission is shifted into PARK (P). Mode 3: All doors unlock when the key is removed from the ignition.
Page 81 Rear Door Security Locks Your vehicle may have this feature. You can lock the rear doors so they can’t be opened from the inside by passengers. To use one of these following: 1. Open one of the rear doors. You will find a security lock lever located on the inside edge of each rear door.
Page 82 Liftgs+e/Liftglass It can be dangerous to drive with the liftgate or liftglass open because carbon monoxide (CO) gas can come into your vehicle. You can’t see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftgate open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate or liftglass:...
Page 83 Windows Leav,,,, ~.1,11\31re11 ,n a vehicle ..ith the winL,ws closed is dangerous. A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 84 Power Windows The controls for the power windows are located on the armrest on each of the side doors. With power windows, the switches operate the windows when the ignition is in RUN, ACCESSORY or when Retained Accessory Power (RAP) is active. The driver’s door has a switch for each of the passenger’s windows as well.
Page 85 Express-Down Window The driver’s and front passenger’s window switches have an express-down feature that allows you to lower the window without holding the switch down. Press the bottom of the driver’s window switch down briefly to activate the express-down feature. Lightly tap the switch to open the window slightly.
Page 86 Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. However, there are ways you can help. Content Theft-Deterrent Your vehicle may be equipped with a content theft-deterrent alarm system.
Page 87 Testing the Alarm The alarm can be tested by following these steps: From inside the vehicle, lower the driver’s window and open the driver’s door. Activate the system by locking the doors with the power door lock switch while the door is open, or with the remote keyless entry transmitter.
Page 88 Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle doesn’t need an elaborate “break-in.” But it will perform better in the long run if you follow these guidelines: Keep your speed at for the first miles km). (805 Don’t drive at any one speed slow for the first...
Page 89 Notice: If your key seems stuck in LOCK and you can’t turn it, be sure you are using the correct key; if so, is it all the way in? Turn the key only with your hand. Using a tool to force it could break the key or the ignition switch.
Page 90 Starting Your Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine won’t start in any other position-that’s a safety feature. To restart when you’re already moving, use NEUTRAL (N) only. Notice: Don’t try to shift to PARK (P) if your vehicle is moving.
Page 91 Engine Coolant Heater Your vehicle may have this feature. In very cold weather, 0°F (-18°C) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 92 Automatic Transmission Operation There are several different positions for your shift lever. PARK (P): This position locks the rear wheels. It’s the best position to use when you start the engine because your vehicle can’t move easily. It is da -erous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set.
Page 93 REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage your transmission. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, sand without damaging your transmission, see If You Are Stuck: In Sand, Mud, Ice or Snow on page 4-44.
Page 94 SECOND (2): This position gives you more power but lower fuel economy than THIRD (3). You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use the brakes off and on. You can also use SECOND ( 2 ) for starting the vehicle from a stop on slippery road surfaces.
Page 95 Four-wheel Drive If your vehicle has four-wheel drive, you can send your engine’s driving power to all four wheels for extra traction. To get the most satisfaction out of four-wheel drive, you must be familiar with its operation. Read the part that follows before using four-wheel drive. You should use two-wheel drive high (2HI) for most normal driving conditions.
Page 96 Shifting the transfer case to NEUTRAL can cause your vehicle to roll even if the transmission is in PARK (P). You or someone else could be seriously injured. the parking brake before placing the transfer case in NEUTRAL. See “Parking Brake” in the Index.
Page 97 Shifting Out of 4LO To shift from 4LO to 4HI, A4WD or 2HI your vehicle must be stopped or moving less than 2 mph (3.2 km/h) with the transmission in NEUTRAL (N) and the engine running. The preferred method for shifting out of 4LO is to have your vehicle moving (1.6 to 3.2 km/h).
Page 98 2-29...
Page 99 Shifting Into Park (P) It can b , --..gerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 100 Leaving Your Vehicle With the Engine RNNrlning It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. If you have four-wheel drive, your vehicle will be free to roll even if your lever is in...
Page 101 Shifting Out of Park (P) Your vehicle has an automatic transmission shift lock control system. You have to fully apply the regular brakes before you can shift from PARK (P) when the ignition is in RUN. See Automatic Transmission Operation on page 2-23. If you cannot shift out of PARK (P), ease pressure on the shift lever.
Page 102 Engine Exhvst Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can’t see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: Your exhaust system sounds strange or different. Your vehicle gets rusty underneath. Your vehicle was damaged in a collision.
Page 103 can be dangerous to get out of if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Don’t leave your vehicle when the engine is running unless you have to. If you’ve left the engine running, the vehicle can move suddenly.
Page 104: Mirrors
Mirrors Automatic Dimming Rearview Mirror with OnStarB and Compass Your vehicle may have an automatic-dimming rearview mirror with a compass and the Onstar@ system. (On/Off): This is the on/off button for the automatic dimming feature and compass. There are three additional buttons for the Onstar@ system.
Page 105 Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. The mirror is set to zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as during a long distance cross-country trip, it will be necessary to adjust for compass variance.
Page 106 Outside Manual Mirrors Adjust your outside mirrors so you can see a little of the side of your vehicle. Fold the mirrors in before entering a car wash. To do this, pull the mirrors in toward the vehicle. Push the mirrors back out when finished.
Page 107 Outside Convex Mirror A convex mirror’s surface is curved so you can see -.-e fror .er’s seat. I I - -I..:. A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right or left lane, you could hit vehicle.
Page 108 Outside Automatic Dimming Mirror with Curb View Assist If your vehicle has this feature, the driver’s and/or passenger’s outside mirror will adjust to a preset tilt position while the vehicle is in REVERSE (R) gear. Curb view assist may be useful when you are parallel parking.
Page 109: Onstar@ System
Onstar@ System Your vehicle may be equipped with the Onstar@ System. Onstar@ uses global positioning system (GPS) satellite technology, wireless communications, and state of the art call centers to provide you with a wide range of safety, security, information and convenience services.
Page 110 Onstar@ Personal Calling With Onstar@ Personal Calling, you have a safer way to stay connected while driving. It’s a hands-free wireless phone that’s integrated into your vehicle. You can place calls nationwide using voice-activated dialing with no contracts, no roaming charges and no access fees. To find out more about Onstar@ Personal Calling, refer to the Onstar@ owner’s guide in your vehicle’s glove box, or call Onstar@ at 1 -888-4-ONSTAR...
Page 111: Homelink@ Transmitter
HomeLink@ Transmitter HomeLink@ , a combined universal transmitter and receiver, provides a way to replace up to three hand-held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems and home lighting. Additional HomeLink@ information can be found on the internet at www.homelink.com or by calling 1-800-355-351 5.
Page 112 Be sure that people and objects are clear of the garage door or gate operator you are programming. When programming a garage door, it is advised to park outside of the garage. is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio frequency.
Page 113 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7. Firmly press and release the “Learn” or “Smart” button.
Page 114 Using HorneLink@ Press and hold the appropriate HomeLink@ button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing HomeLink@ Buttons To erase programming from the three buttons do the following: 1.
Page 115: Storage Areas
Storage Areas Glove Box To open your glove box, pull the handle on the front of the glove box and lower the door. Overhead Console The overhead console includes sunglasses storage, a HomeLink@ transmitter and a travel note recorder (if equipped).
Page 116 You may also press and hold the button with the circle on it while you are speaking and then let it go when you are finished. To play back messages, press the button with the right arrow on it. Pressing the right arrow button more than once will return you to previously recorded messages.
Page 117 Rear Compartment Storage PaneKover Upper Position 2-48 Your vehicle may have this feature. Insert the front corners of the panel into the top guides and slide the panel forward. Press down on the back of the panel to lock it in place. This acts as a cargo shade.
Page 118 Lower Position Insert the front corners of the panel into the lower guides and slide the panel forward. Press down on the back of the panel to lock it in place. To prevent soiling the carpet, the panel may be installed either side up. Notice: To help avoid damage, do not load objects over 200 Ibs.
Page 119 Luggage Carrier If you try to ca something on vehicle that is longer or wider than the luggage carrier like paneling, plywood, a mattress and so forth the wind can catch it as you drive along. This can cause you to lose control.
Page 120 Rear Floor F+wage Lid If any removable convenience itel secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. Your vehicle has a rear floor storage lid located in the rear cargo area that allows you to put items underneath it.
Page 121 Cargo Cover If your vehicle has a cargo cover, you can use it to cover items in the cargo area of your vehicle. To install the cargo cover, do the following: 1. Align the endcap with the pocket in the trim panel located behind the rear seat.
Page 122: Sunroof
Sunroof Your vehicle may be equipped with a power sliding sunroof. To open or close your sunroof, the ignition must be on or Retained Accessory Power (RAP) must be active. Press and release the back of the button in the overhead console to open the sunroof.
Page 123: Vehicle Personalization
Vehicle Personalization Memory Seat Your vehicle may have this feature. The controls are located on the driver’s door, and are used to program and recall memory settings for the driver’s seating and outside mirror positions. Adjust the driver’s seat (including the seatback recliner and lumbar) and both of the outside mirrors to the desired position.
Page 124 Two personalized exit positions can be set by first recalling the driver’s position (by pressing 1 or 2), then positioning the seat in the desired exit position for that driver. Press and hold the button with the exit symbol for three seconds. A double chime will sound to let you know that the position has been stored.
Page 126: Instrument Panel
Section Instrument Panel Overview ... Hazard Warning Flashers Other Warning Devices ... Horn ... Tilt Wheel ... Turn SignaVMultifunction Lever ... Exterior Lamps ... Interior Lamps Accessory Power Outlets ... 3.19 Ashtrays and Cigarette Lighter ... Climate Controls ... Dual Climate Control System Dual Automatic Climate Control System ...
Page 127 Section 3 Audio System(s) Setting the Time ... Radio with CD Radio with Cassette and CD ... Radio with Six-Disc CD ... Rear Seat Entertainment System Rear Seat Audio (RSA) ... Radio Personalization ... Theft-Deterrent Feature (RDS Radios) Instrument Panel 3.63 Audio Steering Wheel Controls ...
Page 129: Instrument Panel Overview
Instrument Panel Overview...
Page 130 The main components of your instrument panel are the following: A. Exterior Lamp Controls B. Air Outlets C. Turn SignaVMultifunction Lever D. Climate Control Steering Wheel Controls E. Instrument Panel Cluster F. Audio Steering Wheel Controls G. Ignition Switch H. Audio System I.
Page 131 The button for the hazard warning flashers is located on top of the steering column. The hazard warning flashers work no matter what position your key is in, and even if the key isn’t in. Press the button all the way down to make your front and rear turn signal lamps flash on and off.
Page 132 Turn SignaVMultifunction Lever The lever on the left side of the steering column includes the following: : Turn and Lane Change Signals : Headlamp High/Low-Beam Changer Flash-to-Pass Feature : Windshield Wipers Windshield Washer : Cruise Control (If Equipped) Turn and Lane Change Signals To signal a lane change, just raise or lower the lever until the arrow starts to flash.
Page 133 If a bulb is burned out, replace it to help avoid an accident. If the arrows don’t go on at all when you signal a turn, check the fuse. See Fuses and Circuit Breakers page 5-92 and check for burned-out bulbs. If you have a trailer towing option with added wiring for the trailer lamps, a different turn signal flasher is used.
Page 134 Windshield Wipers (Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer. (Off): To stop the wipers, move the band to off.
Page 135 Windshield Washer (Windshield Washer): To spray washer fluid on the windshield, press the windshield washer paddle. The wipers will clear the window and then either stop or return to your preset speed. In freezing weather, don’t use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.
Page 136 Cruise Control (On): Move the switch to this position to turn the cruise control system on. (Resume/Accelerate): Move the switch to this position to resume a set speed or to accelerate. ";3- (Set): Press this button, located at the end of the lever, to set a speed.
Page 137 Setting Cruise Control 1. Move the cruise control switch 2. Get up to the speed you want. 3. Press in the set button at the end of the lever and release it. 4. Take your foot off the accelerator pedal. The accelerator pedal will not go down.
Page 138 Reducing Speed While Using Cruise Control Press in the set button at the end of the lever until you reach the lower speed you want, then release it. To slow down in very small amounts, briefly press the set button. Each time you do this, you’ll go about 1 mph (1.6 km/h) slower.
Page 139 Exterior Lamps Your exterior lamps knob is located on your instrument panel to the left of the steering wheel. :::. (Off): Turn the knob to this symbol and release it to turn off the Daytime Running Lamps (DRL) and the automatic headlamps.
Page 140 There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems, so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor sees a change in lighting lasting longer than the delay.
Page 141 Fog Lamps Your vehicle may have this feature. Use your fog lamps for better vision in foggy or misty conditions. Your ignition must be in RUN for your fog lamps to work. The fog lamp button is located on the instrument panel to the right of the exterior lamps knob.
Page 142 Dome Lamp Override The dome override button is located below the exterior lamps knob. To turn the dome lamps off, press the button. The dome lamps will remain off when a door is open. This will override the illuminated entry feature unless you use your keyless entry transmitter to unlock the vehicle.
Page 143 Reading Lamps Press the lens on the lamp located above the doors to turn the reading lamps on and off. Dome Lamps The dome lamps will come on when you open a door unless the dome lamp override is pressed in. You can also turn the dome lamps on by turning the thumbwheel, located next to the exterior lamps knob, all the way up to the top detent position.
Page 144 Accessory Power Outlets With the accessory power outlets, you auxiliary electrical equipment such as a cellular telephone or CB radio. Your vehicle may have accessory power outlets. The first two outlets are located below the cigarette lighter and the rear wiper switch on the instrument panel. The third outlet is located on the rear of the center console.
Page 145: Climate Controls
Climate Controls Dual Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. If the knob is in off outside air will still enter the vehicle, and will be directed based on the position of the mode knob.
Page 146 Temperature Control Driver’s Side: The lever on the left side of the climate control panel is used to raise or lower the temperature on the driver’s side of the vehicle. Slide the lever up or down to adjust the temperature. Passenger’s Side: The lever on the right side of the climate control panel is used to raise or lower the temperature on the passenger’s side of the vehicle.
Page 147 Rear Window Defogger The lines you see on the rear window warm the glass. Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is active. The rear window defogger will automatically turn off approximately ten minutes after the button is pressed.
Page 148 Operation Tips Keep the hood and front air inlets free of ice, snow, or any other obstruction (such as leaves). The heater and defroster will work far better, reducing the chance of fogging the inside of your windows. When you enter a vehicle in cold weather, turn the fan knob all the way to the right for a few moments before driving.
Page 149 +d (Mode): Press this button to manually select the air delivery mode to the floor, instrument panel, or windshield outlets. The system will stay in the selected mode until the mode button is pressed again or the AUTO button is pressed. Driver’s Side Temperature Knob: Turn this knob clockwise or counterclockwise to manually raise or lower the temperature on the driver’s side of the vehicle.
Page 150 Manual Operation To change the current setting, select one of the following: Lfi@ (Fan): This button allows you to manually adjust the fan speed. Press the up arrow to increase fan speed and the down arrow to decrease fan speed. The display will change to show you the selected fan speed and the driver’s side temperature setting for five seconds.
Page 151 You may notice a slight change in engine performance when the air-conditioning compressor shuts off and turns on again. This is normal. (Air Conditioning Off): When you turn the air conditioning off, this symbol will appear on the display. When the air conditioning is selected or in AUTO mode, the system will run the air conditioning automatically.
Page 152 Notice: Don’t use a razor blade or something else sharp on the inside of the rear window. If you do, you could cut or damage the defogger and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid.
Page 153 Rear Climate Control System Your vehicle has one of the following rear comfort control systems. With either system, the rear comfort controls will be disabled when the front comfort control system is in defrost. This occurs to provide maximum airflow to clear the windshield. Envoy 3-28 The temperature of the air coming through the rear...
Page 154 If your vehicle has the rear seat audio system, the lower buttons are used to adjust the rear seat comfort controls. The temperature of the air coming through the rear outlets is determined by the front passenger’s temperature setting. The button with the up and down arrows on it regulates the fan speed.
Page 155 Envoy XL To operate the rear air conditioning system, the front air conditioning system must be on. With the front air conditioning system off, the rear system controls can only be used to circulate air in the rear of the vehicle. To adjust the airflow speed, turn the fan knob (driver override switch), located on the floor console to 1, 2 or The rear mode and temperature positions now mimic...
Page 156 Envoy XL Turn the knobs on the control panel to choose a fan speed, temperature and direction of airflow. Selecting panel mode will deliver air to the four headliner outlets. Selecting bi-level mode will deliver warmer air to the third seat floor outlet and cooler air to the headliner outlets.
Page 157 Steering Wheel Climate Controls You can adjust the fan speed and temperature of the front climate control system by using the buttons located on your steering wheel. (Fan): Press the up or down arrow on this switch to increase or decrease the fan speed. &...
Page 158: Warning Lights, Gages And Indicators
Warning Lights, Gages and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 159 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel you’ve used, and many other thing you’ll need to know to drive safely and economically.
Page 160 Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). The odometer mileage can be checked without the vehicle running.
Page 161 Safety Belt Reminder Light When the key is turned to RUN, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. The safety belt light will also come on and stay on for several seconds, then it will flash for...
Page 162 If the air bag readiness light stays on after you start your vehicle, it means the air bag system may not be working properly. The air bags in your vehicle may not inflate in a crash, or they could even inflate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the air bag readiness light stays on after you start your vehicle.
Page 163 Voltmeter Gage When your engine is not running, but the ignition is on (in RUN), this gage shows your battery's state of charge in DC volts. When the engine is running, the gage shows the condition of the charging system. Readings between the low and high warning zones indicate the normal operating range.
Page 164 Brake System Warning Light When the ignition is on, the brake system warning light will come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. If it stays on after your parking brake is fully released, it means you have a brake problem.
Page 165 Anti-Lock Brake System Warning Light With the anti-lock brake system, this light will come on when you start your engine and may stay on for several seconds. That's normal. A chime may also sound when the light comes on. If the light stays on, or comes on when you're driving, your vehicle needs service.
Page 166 Malfunction Indicator Lamp Service Engine Soon Light in the United States or Check Engine Light in Canada SERVICE ENGINE SOON United States Your vehicle is equipped with a computer which monitors operation of the fuel, ignition and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life...
Page 167 This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light doesn’t come on, have it repaired. This light will also come on during a malfunction in one of two ways: Light Flashing A misfire condition has been...
Page 168 Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel.
Page 169 Oil Pressure Gage United States The oil pressure gage shows the engine oil pressure in psi (pounds per square inch) when the engine is running. Canadian vehicles indicate pressure in kPa (kilopascals). 3-44 Don't keep dri -..ig if the oil pressure is low. If you do, your engine can become so hot that it catches fire.
Page 170 Change Engine Oil Light CHANGE United States This light is displayed when the engine oil needs to be changed. Once the engine oil has been changed, the CHANGE ENG OIL light must be reset. Until it is reset, the light will be displayed when the engine is on.
Page 171 Cruise Control Light CRUISE United States Your vehicle may have this feature. The CRUISE light appears whenever you set your cruise control. 3-46 Reduced Engine Power Light REDUCED ENGINE Canada United States This light is displayed when a noticeable reduction in the vehicle's performance may occur.
Page 172 Service Four-wheel Drive Warning Light SERVICE United States This light should come on briefly when you turn on the ignition, as a check to show you it is working. The SERVICE 4WD light comes on to indicate that there may be a problem with the drive system and service is required.
Page 173 Gate Ajar Light GATE AJAR United States If this light comes on, your liftgate or liftglass is ajar. Try closing the liftgate or liftglass again. Never drive with the liftgate or liftglass even partially open. 3-48 Fuel Gage Canada United States When the ignition is on, the fuel gage tells you about how much fuel you have remaining.
Page 174 Here are four things that some owners ask about. None of these show a problem with your fuel gage: At the gas station, the gas pump shuts the gage reads full. It takes a little more or less fuel to fill up than the gage indicated.
Page 175: Driver Information Center (Dic)
Driver Information Center (DIC) Your vehicle may have this feature. The DIC display is located on the instrument panel cluster above the steering wheel. The DIC can display information such as the trip odometer, fuel economy and personalization features. The DIC buttons are located on the steering wheel.
Page 176 Trip Information Use the trip information button to scroll through the odometer, TRIP A, TRIP B and TIMER. Odometer Press the trip information button until the odometer appears on the display. This shows the total distance the vehicle has been driven in either miles or kilometers. Pressing the reset stem located on the instrument cluster with the vehicle off will also display the odometer.
Page 177: Maintenance Schedule
Fuel Information Use the fuel information button to scroll through the range, average fuel economy, instant fuel economy and the GM Oil Life SystemTM. Fuel Range Press the fuel information button until RANGE appears to display the remaining distance you can drive without refueling.
Page 178 Personalization You can program certain features to a preferred setting for up to two people. Press the personalization button to scroll through the following personalization features. All of the personalization options may not be available on your vehicle. Only the options available will be displayed on your DIC.
Page 179 Automatic Locking Press the select button while AUTOMATIC LOCKING is displayed on the DIC to scroll through the following choices: LOCK DOORS OUT OF PARK (default) LOCK DOORS MANUALLY LOCK DOORS WITH SPEED If you choose for the doors to lock out of park, the doors will lock when the vehicle is shifted out of PARK (P).
Page 180 Seat Position Recall Press the personalization button until SEAT POSITION RECALL appears in the display. To select your personalization for seat position recall, press the select button while SEAT POSITION RECALL is displayed on the DIC. Pressing the select button will scroll through the following choices: SEAT POSITION RECALL OFF (default) SEAT POSITION RECALL AT KEY IN...
Page 181 Remote Lock Feedback Press the personalization button until REMOTE LOCK FEEDBACK appears in the display. To select your personalization for the feedback you will receive when locking the vehicle with the remote keyless entry transmitter, press the select button while REMOTE LOCK FEEDBACK is displayed on the DIC.
Page 182 Headlamps on at Exit Press the personalization button until HEADLAMPS ON AT EXIT appears in the display. To select your personalization for how long the headlamps will stay on when you turn off the vehicle, press the select button while HEADLAMPS ON AT EXIT is displayed on the DIC.
Page 183 Easy Exit Driver Seat Press the personalization button until EASY EXIT DRIVER SEAT appears in the display. To select your personalization for seat position exit, press the select button while EASY EXIT DRIVER SEAT is displayed on the DIC. Pressing the select button will scroll through the following choices: EASY EXIT SEAT: OFF (default) EASY EXIT SEAT:...
Page 184 Display Language To select your personalization for display language, press the select button while DISPLAY LANGUAGE is displayed on the DIC. Pressing the select button will scroll through the available languages: Choosing a language will display all of the information on the DIC in the desired language.
Page 185 DIC Warnings and Messages Warning messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. More than one message may appear at one time.
Page 186 SERVICE BRAKE SYSTEM If a problem occurs with the brake system this message will appear on the DIC. If this message appears, stop as soon as possible and turn off the vehicle. Restart the vehicle and check for the message on the DIC display. If the message is still displayed, or appears again when you begin driving, the brake system needs service.
Page 187 ICE POSSIBLE If the outside temperature reaches a level where ice could form on the roadway, this message may appear on the DIC. If the temperature rises to a safe level, the message will clear. Pressing the select button will acknowledge this message and clear it from the DIC display.
Page 188: Audio System(S)
Audio System(s) Notice: Before you add any sound equipment to your vehicle like a tape player, CB radio, mobile telephone or two-way radio be sure you can add what you want. If you can, it’s very important to do it properly. Added sound equipment may interfere with the operation of your vehicle’s engine, Delphi Electronics radio or other systems, and even damage them.
Page 189 Radio with CD Playing the Radio PWR (Power): Press this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease volume. 3-64 AUTO (Automatic Volume): automatic With volume, your audio system will adjust automatically to make up for road and wind noise as you drive.
Page 190 Finding a Station AM FM: Press this button to switch between AM, FMI and FM2. The display will show your selection. TUNE: Turn this knob to choose radio stations. SEEK : Press the right or the left arrow to seek to the next or to the previous station and stay there.
Page 191 Setting the Tone (BassTTreble) AUDIO: Press and release the AUDIO knob until BASS or TREB appears on the display. Turn the knob to increase or to decrease. The display will show the bass or treble level. If a station is weak or noisy, you may want to decrease the treble.
Page 192 Using RDS Your audio system is equipped with a Radio Data System (RDS). RDS features are available for use only FM stations that broadcast RDS information. Using this system, your radio can do the following: Seek to stations broadcasting the selected type of programming, receive announcements concerning local and national emergencies,...
Page 193 AM FM (Alternate Frequency): Alternate frequency allows the radio to switch to a stronger station with the same program type. Press and hold AM FM for two seconds to turn alternate frequency on. AF ON will appear on the display. The radio may switch to stronger stations.
Page 194 When a traffic announcement comes on the current station or on a related network station, you will hear it, even if the volume is muted or a compact disc is playing. The traffic symbol and TRAF will appear on the display while the announcement plays.
Page 195 advance quickly within a track. Press and hold this pushbutton for less than two seconds to advance at six times the normal playing speed. Press and hold it for more than two seconds to advance at 17 times the normal playing speed. Release it to play the passage. The display will show ET and the elapsed time.
Page 196 Radio with Cassette and CD Playing the Radio PWR (Power): Press this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease volume. AUTO VOL (Automatic Volume): With volume, your audio system adjusts automatically to make up for road and wind noise as you drive.
Page 197 Finding a Station AM FM: Press this button to switch between AM, FMl and FM2. The display will show your selection. TUNE: Turn this knob to choose radio stations. SEEK Press the right or the left arrow to seek to the next or to the previous station and stay there. The radio will seek only to stations that are in the selected band and only to those with a strong signal.
Page 198 Setting the Tone (Bassmreble) AUDIO: Push and release the AUDIO knob until BASS or TREB appears on the display. Turn the knob to increase or to decrease. The display will show the bass or treble level. If a station is weak or noisy, you may want to decrease the treble.
Page 199 Adjusting the Speakers (Balance/Fade) AUDIO: To adjust the balance to the right and the left speakers, push and release the AUDIO knob until BAL appears on the display. Turn the knob to move the sound toward the right or the left speakers. To adjust the fade to the front and the rear speakers, push and release the AUDIO knob until FADE appears on the display.
Page 200 DlSP (Display): Press this knob to change what appears on the display while using RDS. The display options are station name, RDS station frequency, PTY and the name of the program (if available). To change the default on the display, push the knob until you see the display you want, then hold the knob for two seconds.
Page 201 INFO (Information): If the current station has a message, the information symbol will appear on the display. Press this button to see the message. The message may display the artist and song title, call in phone numbers, etc. If the whole message is not displayed, parts of it will appear every three seconds.
Page 202 Playing a Cassette Tape Your tape player is built to work best with tapes that are up to 30 to 45 minutes long on each side. Tapes longer than that are so thin they may not work well in this player. The longer side with the tape visible should face to the right.
Page 203 FWD (Forward): Press this pushbutton to advance quickly to another part of the tape. Press this pushbutton again to return to playing speed. The radio will play while the tape advances. The station frequency and FWD will appear on the display. You may select stations during forward operation by using TUNE and SEEK.
Page 204 Playing a Compact Disc Insert a disc partway into the slot, label side up. The player will pull it in and the disc should begin playing. The display will show the CB symbol. If you want to insert a compact disc with the ignition off, first press DlSP or EJT.
Page 205 DlSP (Display): Press this knob to see how long the current track has been playing. ET and the elapsed time will appear on the display. To change the default on the display (track or elapsed time), push the knob until you see the display you want, then hold the knob for two seconds.
Page 206 qadi0 with Six-Disc CD Playing the Radio PWR (Power): Push this knob to turn the system and off. VOL (Volume): Turn the knob to increase decrease volume. AUTO VOL (Automatic Volume): Your system has a feature called automatic volume. With this feature, your audio system adjusts automatically to make up for road and wind noise as you drive.
Page 207 Finding a Station AM FM: Press this button to switch between AM, FMI and FM2. The display will show your selection. TUNE: Turn this knob to select radio stations. k SEEK >I : Press the right or the left arrow to go to the next or to the previous station and stay there.
Page 208 Setting the Tone (Bassnreble) AUDIO: Push the AUDIO knob until BASS, MID or TREB appears on the display. Turn the knob to increase or to decrease. If a station is weak or noisy, you may want to decrease the treble. To adjust bass, midrange or treble to the middle position, select BASS, MID or TREB and push and hold the AUDIO knob.
Page 209 Using RDS Your audio system is equipped with a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. Using this system, the radio can do the following: Seek to stations broadcasting the selected type of programming, receive announcements concerning local and national emergencies,...
Page 210 SCAN: You can also scan through the channels within a cateaow bv Derformina the followina: " " Press the P-TYPE button. P-TYPE and the last selected PTY will be displayed on the screen. Select a category by turning the P-TYPE knob. Once the desired category is displayed, press and hold either SCAN arrow, and the radio will begin scanning within your chosen category.
Page 211 RDS Messages ALERT!: Alert warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! will appear on the display. You will hear the announcement, even if the volume is muted or a compact disc is playing. If the compact disc player is playing, play will stop during the announcement.
Page 212 Playing a Compact Disc If an error appears on the display, see “Compact Disc Messages” later in this section. LOAD CD : Press the LOAD side of this button to load CDs into the compact disc player. This compact disc player will hold up to six discs. To insert one disc, do the following: Turn the ignition on.
Page 213 Playing a Specific Loaded Compact Disc For every CD loaded, a number will appear on the radio display. To play a specific CD, first press the CD AUX button to start playing a CD. Then press the numbered pushbutton that corresponds to the CD you want play.
Page 214 RPT (Repeat): With repeat, you can repeat one track or an entire disc. To use repeat, do the following: To repeat the track you are listening to, press and release the RPT button. RPT will appear on the display. Press RPT again to turn it off. To repeat the disc you are listening to, press and hold the RPT button for two seconds.
Page 215 Using Song List Mode The integrated six-disc CD changer has a feature called song list. This feature is capable of saving 20 track selections. To save tracks into the song list feature, perform the following steps: 1. Turn the disc player on and load it with at least one disc.
Page 216 After a track has been deleted, the remaining tracks are moved up the list. When another track is added to the song list, the track will be added to the end of the list. To delete the entire song list: perform the following steps: 1.
Page 217 Rear Seat Entertainment System Your vehicle may have the optional Digital Versatile Disc (DVD) entertainment system. The entertainment system includes a DVD player, a video display screen, two sets of IR (Infrared) wireless headphones, a remote control and an instructional video disc. Before You Drive The video entertainment system is for passengers in the second and third row seats only.
Page 218 Battery Replacement To change the batteries, do the following: 1. Loosen the screw on the battery compartment door located the left side of the headphones. 2. Replace the two AAA batteries in the compartment. Make sure that they are installed correctly. 3.
Page 219 Video Screen The video screen is located in the overhead console. 3-94 To use the video screen, do the following: 1. Push forward on the release button and the screen will fold down. 2. Push the screen away from you and adjust its position as desired.
Page 220 DVD Player The video screen will default to off when an audio CD is played. Home recorded CDs (CDRs) may not play in 3-95...
Page 221 Playing a Disc To play a disc, gently insert the disc with the label side slot. up into the loading The DVD player will continue loading the disc and the player will automatically start. If a disc is already in the player, press the play/pause button on the face of the player or on the remote control.
Page 222 DVD Messages The following errors may be displayed: Disc Format Error: This message will be displayed if a disc is inserted upside down, if the disc is not able to be read or if the disc format is not compatible. Disc Play Error: This message will be displayed if the mechanism can not play the disc.
Page 223 Remote Control Buttons PWR (Power): Press this button to turn the DVD player on or off. , 1 1 1 PLAY/PAUSE: Press this button to play a disc. Press this button while a disc is playing to pause. Press it again to continue playing. 3-98 STOP: Press this button to stop playing, reversing...
Page 224 NEXT: Press this button to jump to the beginning of the next chapter. This button may not work when the DVD is playing the copyright or the previews. MENU: Press this button to view the media menu. The media menu is different on every disc. Use the up and down and the right and the left arrow buttons to move the cursor around the media menu.
Page 225 RTN (Return): When a DVD menu is active and this button is pressed, the selected option will be disabled. This button could have different functions with different discs. SCREEN BRIGHTNESS: Press the plus or the minus symbol to increase or decrease the brightness the screen.
Page 226 Recommended Action Problem No power The ignition might be off. The parental control button might have been pressed. (The power LED will flash.) Disc will not play. The lnputrritle on the remote might be set for auxiliary. The disc is upside down or is not compatible.
Page 227 Problem Recommended Action The language in the Press and hold the audio or on the screen COMP/AUDIO button on is wrong. the remote. This will access the DVD’s main menu. Then follow the prompts. The remote does Point the remote directly not work.
Page 228 Recommended Action Problem If the STOP button was When I return to the DVD pressed once, it resumes from the system menu, play from where it left off. sometimes it plays from If the STOP button was the beginning and sometimes from where pressed twice, it will it left off.
Page 229 Rear Seat Audio (RSA) This feature allows rear seat passengers to listen to any of the music sources: radio, cassette tapes or CDs. The rear seat passengers can only control the music sources that the front seat passengers are not listening to. For example, rear seat passengers may listen to a cassette tape or CD through headphones while the driver listens to the radio through the front speakers.
Page 230 PROG (Program): Press this button playing a cassette tape or a CD and listening radio. The inactive tape or CD will remain safely inside the radio for future listening. SEEK: Press the SEEK button to seek to the next station and stay there. The display will show your selection.
Page 231 Audio Steering Wheel Controls If your vehicle has this feature, certain radio functions can be operated by using the controls on your steering wheel. AM/FM: Press this button to switch between AM, FM1 and FM2. When playing a cassette tape or compact disc, press this button to listen to the radio.
Page 232 Care of Your Cassette Tape Player A tape player that is not cleaned regularly can cause reduced sound quality, ruined cassettes or a damaged mechanism. Cassette tapes should be stored in their cases away from contaminants, direct sunlight and extreme heat. If they aren’t, they may not operate properly or may cause failure of the tape player.
Page 233 After you clean the player, press and hold the EJT button for five seconds to reset the CLEAN indicator. The radio will display CLEANED to show the indicator was reset. Cassettes are subject to wear and the sound quality may degrade over time. Always make sure the cassette tape is in good condition before you have your tape player serviced.
Page 234: Driving Your Vehicle
Your Driving. the Road. and Your Vehicle ... 4-2 Defensive Driving ... 4.2 Drunken Driving ... Control of a Vehicle ... 4-5 Braking ... 4-5 Traction Assist System (TAS) ... Locking Rear Axle ... Steering ... Off-Road Recovery Passing ... Loss of Control ...
Page 235: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-9. Defensive driving really means “be ready for anything.”...
Page 236 Many adults by some estimates, nearly half the adult population choose never to drink alcohol, so they never drive after drinking. For persons under 21, it’s against the law in every U.S. state to drink alcohol. There are good medical, psychological and developmental reasons for these laws.
Page 237 this means that a woman generally will reach a higher BAC level than a man of her same body weight when each has the same number of drinks. The law in an increasing number of U.S. states, and throughout Canada, sets the legal limit at 0.08 percent. In some other countries, the limit is even lower.
Page 238 Control of a Vehicle You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering and the accelerator. All three systems have to do their work at the places where the tires meet the road. Sometimes, as when you’re driving on snow or ice, it’s easy to ask more of those control systems than the tires and road can provide.
Page 239 Avoid needless heavy braking. Some people drive in spurts heavy acceleration followed by heavy braking rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking.
Page 240 Let’s say the road is wet and you’re driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here’s what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each front wheel and at both rear wheels.
Page 241 Remember: Anti-lock doesn’t change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you won’t have time to apply your brakes if that vehicle suddenly slows or stops.
Page 242 The TRAC OFF light on the button will come on under following conditions: The Traction Assist System is turned off, either by pressing the TAS on/off button or by turning off the automatic engagement feature of the TAS. The transmission is in FIRST (1) gear; TAS will not operate in this gear.
Page 243 The next time you start your vehicle, the TAS will not automatically come on. You can restore the automatic feature by using the same procedure. Whether the TAS is set to come on automatically or not, you can always turn the system on or off by pressing the TAS on/off button.
Page 244 What should you do if this ever happens? Ease up on the accelerator pedal, steer the vehicle the way you want it to go, and slow down. Speed limit signs near curves warn that you should adjust your speed. Of course, the posted speeds are based on good weather and road conditions.
Page 245 Off-Road Recovery You may find that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 246 Do not get too close to the vehicle you want to pass while you’re awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you’re following a larger vehicle. Also, you won’t have adequate space if the vehicle ahead suddenly slows or stops.
Page 247 Loss of Control Let’s review what driving experts say about what happens when the three control systems (brakes, steering and acceleration) don’t have enough friction where the tires meet the road to do what the driver has asked. In any emergency, don’t give up. Keep trying to steer and constantly seek an escape route or area of less danger.
Page 248 Off-Road Driving with Your Four-Wheel-Drive Vehicle This off-road guide is for vehicles that have four-wheel drive. Also, see Braking on page 4-5. If your vehicle doesn’t have four-wheel drive, you shouldn’t drive off-road unless you’re on a level, solid surface. Off-road driving can be great fun.
Page 249 Loading Your Vehicle for Off-Road Driving There are some important things to remember about how to load your vehicle. The heaviest things should be on the load floor and forward of your rear axle. Put heavier items as far forward as you can. Be sure the load is secured properly, so driving on the off-road terrain doesn’t toss things around.
Page 250 Environmental Concerns Off-road driving can provide wholesome and satisfying recreation. However, it also raises environmental concerns. We recognize these concerns and urge every off-roader to follow these basic rules for protecting the environment: Always use established trails, roads and areas that have been specially set aside for public off-road recreational driving;...
Page 251 Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle is to control your speed. Here are some things to keep in mind. At higher speeds: you approach things faster and you have less time to scan the terrain for obstacles.
Page 252 When you drive over obstacles or rough terrain, keep a firm grip on the steering wheel. Ruts, troughs or other surface features can jerk the wheel out of your hands if you’re not prepared. When you drive over bumps, rocks, or other obstacles, your wheels can leave the ground.
Page 253 Approaching a Hill When you approach a hill, you need to decide if it’s one of those hills that’s just too steep to climb, descend or cross. Steepness can be hard to judge. On a very small hill, for example, there may be a smooth, constant incline with only a small change in elevation where you can easily see all the way to the top.
Page 254 Ease up on your speed as you approach the top of the hill. Attach a flag to the vehicle to make you more visible to approaching traffic on trails or hills. Sound the horn as you approach the top of the hill to let opposing traffic know you’re there.
Page 255 must Here are some things you not do if you stall, or are about to stall, when going up a hill. Never attempt to prevent a stall by shifting into NEUTRAL (N) to “rev-up” the engine and regain forward momentum. This won’t work. Your vehicle will roll backwards very quickly and you could go out of control.
Page 256 Driving Downhill When off-roading takes you downhill, you’ll want to consider a number of things: How steep is the downhill? Will I be able to maintain vehicle control? What’s the surface like? Smooth? Rough? Slippery? Hard-packed dirt? Gravel? Are there hidden surface obstacles? Ruts? Logs? Boulders? What’s at the bottom of the hili? Is there a hidden creek bank or even a river bottom with large...
Page 257 Am I likely to stall when going downhill? It’s much more likely to happen going uphill. But if it happens going downhill, here’s what to do. Stop your vehicle by applying the regular brakes. Apply the parking brake. Shift to PARK (P) and, while still braking, restart the engine.
Page 258 Driving across an incline that’s too steep will make your vehicle roll over. You could be seriously injured or killed. If you have any doubt about the steepness of the incline, don’t drive across it. Find another route instead. What if I’m driving across an incline that’s not too steep, but I hit some loose gravel and start to slide downhill.
Page 259 Stalling on an Incline If your vehicle stalls when you’re crossing an incline, be sure you (and your passengers) get out on the uphill side, even if the door there is harder to open. If you get out on the downhill side and the vehicle starts to roll over, you’ll be right in its path.
Page 260 Hard packed snow and ice offer the worst tire traction. On these surfaces, it’s very easy to lose control. On wet ice, for example, the traction is so poor that you will have difficulty accelerating. And if you do get moving, poor steering and difficult braking can cause you to slide out of control.
Page 261 After Off-Road Driving Remove any brush or debris that has collected on the underbody, chassis or under the hood. These accumulations can be a fire hazard. After operation in mud or sand, have the brake linings cleaned and checked. These substances can cause glazing and uneven braking.
Page 262 Since you can’t see as well, you may need to slow down and keep more space between you and other vehicles. Slow down, especially on higher speed roads. Your headlamps can light up only so much road ahead. In remote areas, watch for animals, If you’re tired, pull off the road in a safe place and rest.
Page 263 Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you can't stop, accelerate or turn as well because your tire-to-road traction isn't as good as on dry roads. And, if your tires don't have much tread left, you'll get even less traction.
Page 264 Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you can’t, try to slow down before you hit them. .--.
Page 265 D%ng Through Flowing Water Flowing or rushing water creates strong forces. If you try to drive through flowing might at a low water crossing, your vehicle can be carried away. As little as six inches of flowing water can carry away a smaller vehicle. If this happens, you and other vehicle occupants could drown.
Page 266 City Driving One of the biggest problems with city streets is the amount of traffic on them. You’ll want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: Know the best way to get to where you are going.
Page 267 Freeway Driving Mile for mile, freeways (also called thruways, parkways, expressways, turnpikes or superhighways) are the safest of all roads. But they have their own special rules. 4-34 The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 268 Once you are moving on the freeway, make certain you allow a reasonable following distance. Expect to move slightly slower at night. When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up.
Page 269 Highway Hypnosis there actually such a condition as “highway hypnosis”? Or is it just plain falling asleep at the whee.l? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 270 Hill and Mountain Roads Driving on steep hills or mountains is different from driving in flat or rolling terrain. If you drive regularly in steep country, or if you’re planning to visit there, here are some tips that can make your trips safer and more enjoyable. Your See Off-Road Driving with Four-Wheel-Drive...
Page 271 Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Your brakes will have to do all the work of slowing down. They could get so hot that they wouldn’t work well. You would then have poor braking or even none going down a hill.
Page 272 Winter Driving Here are some tips for winter driving: Have your vehicle in good shape for winter. You may want to put winter emergency supplies in your vehicle. Include an ice scraper, a small brush or broom, a supply of windshield washer fluid, a rag, some winter outer clothing, a small shovel, a flashlight, a red cloth and reflective warning triangles.
Page 273 Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You’ll have a lot less traction or “grip”...
Page 274 Your anti-lock brakes improve your vehicle’s stability when you make a hard stop on a slippery road. Even though you have an anti-lock braking system, you’ll want to begin stopping sooner than you would on page dry pavement. See Braking on Allow greater following distance on any slippery road.
Page 275 Here are some things to do to summon help and keep yourself and your passengers safe: Turn on your hazard flashers. Tie a red cloth to your vehicle to alert police that you’ve been stopped by the snow. Put on extra clothing or wrap a blanket around you.
Page 276 Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You can’t see it or smell it, so you might not know it is in your vehicle.
Page 277 If You Are Stuck: In Sand, Mud, Ice or Snow In order to free your vehicle when it is stuck, you will need to spin the wheels, but you don’t want to spin your wheels too fast. The method known as “rocking” can help you get out when you’re stuck, but you must use caution.
Page 278: Towing
Towing Towing Your Vehicle Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 7-5. If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing”...
Page 279 Dinghy Towing When towing your vehicle, turn the ignition off. To prevent your battery from draining while towing, remove the Ignition A and the Ignition B fuses from the engine compartment fuse block. Be sure to reinstall the fuse when you reach your destination. Two-Wheel-Drive Vehicles Two-wheel-drive vehicles should not be towed with all four wheels on the ground.
Page 280 4. Shift the transfer case to NEUTRAL (N). See “Four-Wheel Drive” in the Index for the proper procedure to select the NEUTRAL position for your vehicle. 5. Release the parking brake only after the vehicle being towed is firmly attached to the towing vehicle.
Page 281 Loading Your Vehicle FER’S MANUAL FOR ADDITIONAL The Certificationnire label is found on the driver’s door edge, above the door latch. The label shows the size of your original tires and the inflation pressures needed to obtain the gross weight capacity of your vehicle.
Page 282 Do not load your vehicle any heavier than the GVWR, or either the maximum front or rear GAWR. If you do, parts on your vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash.
Page 283 Electronically Controlled Air Suspension System Your vehicle may be equipped with an electronically controlled air suspension system that automatically keeps your vehicle level as you load and unload. The system includes a compressor, two height sensors and two air springs supporting the rear axle. The system also has an internal clock to prevent overheating.
Page 284 Overload Protection The air suspension system is equipped with overload protection. Overload protection is designed to protect the air suspension system, and it is an indicator to the driver that the vehicle is overloaded. When the overload protection mode is on, it will not allow damage to the air compressor.
Page 285 Towing a Trailer If you don’t use the correct eql drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well at all. You and your passengers could be seriously injured.
Page 286 If You Do Decide To Pull A Trailer If you do, here are some important points: There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only but also where you’ll be driving. A good source for this information can be state or provincial police.
Page 287 Weight of the Trailer How heavy can a trailer safely be? It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a trailer are all important. And, it can also depend on any special equipment that you have on your vehicle.
Page 288 4WD Envoy XL (L6 Engine) 2WD Envoy XL (V8 Engine) 4WD Envoy XL (V8 Engine) *The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equipment and conversion. The GCWR for your vehicle should not be exceeded.
Page 289 Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Page 290 Hitches It’s important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why you’ll need the right hitch. Here are some rules to follow: If you’ll be pulling a trailer that, when loaded, will weigh more than 4,000 Ibs.
Page 291 D 4 n g with a Trailer If you have a rear-most window open and you pull a trailer with your vehicle, carbon monoxide (CO) could come into your vehicle. You can’t see or smell CO. It can cause unconsciousness or death. See “Engine Exhaust”...
Page 292 Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer. This can help you avoid situations that require heavy braking and sudden turns. Passing You’ll need more passing distance up ahead when you’re towing a trailer.
Page 293 Driving On Grades Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you don't shift down, you might have to use your brakes so much that they would get hot and no longer work well. You can tow in DRIVE (D).
Page 294 It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicie can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured.
Page 295 Trailer Wiring Harness Your vehicle may be equipped with the seven-wire trailer towing harness. This harness has a seven-pin universal heavy-duty trailer connector that is attached to a bracket on the hitch platform. The seven-wire harness contains the following trailer circuits: 4-62 Yellow: Left Stopnurn Signal Dark Green: Right Stopllurn Signal...
Page 296: Service And Appearance Care
Section Service Doing Your Own Service Work ... Adding Equipment to the Outside of Your Vehicle Fuel ... Gasoline Octane Gasoline Specifications California Fuel ... Additives Fuels in Foreign Countries ... Filling Your Tank ... Filling a Portable Fuel Container ... Checking Things Under the Hood Hood Release ...
Page 297 Section 5 Appearance Care ... 5.82 Cleaning the Inside of Your Vehicle ... 5-82 Care of Safety Belts ... Weatherstrips Cleaning the Outside Your Vehicle ... 5-85 Sheet Metal Damage ... Finish Damage ... Underbody Maintenance ... Chemical Paint Spotting ... GM Vehicle Care/Appearance Materials ...
Page 298: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you’ll go to your dealer for all your service needs. You’ii get genuine GM parts and GM-trained and supported service people. We hope you’ll want to keep your GM vehicle all GM. Genuine GM parts have one of these marks:...
Page 299 Doing Your Own Service Work If you want to do some your own service work, you’ll want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7- 10.
Page 300: Fuel
Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle. Gasoline Octane Use regular unleaded gasoline with a posted octane of 87 or higher. If the octane is less than 87, you may get a heavy knocking noise when you drive.
Page 301 California Fuel If your vehicle is certified to meet California Emission Standards (see the underhood emission control label), it is designed to operate on fuels that meet California specifications. If this fuel is not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance may be affected.
Page 302 Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel may be hard to find. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel wouldn’t be covered by your warranty.
Page 303 While refueling, hang the fuel cap by the tether using the hook located on the inside of the filler door. To remove the fuel cap, turn it slowly to the left (counterclockwise). The fuel cap has a spring in it. If you let go of the cap too soon, it will spring back to the right.
Page 304 When you put the fuel cap back on, turn it to the right (clockwise) until you hear a clicking sound. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
Page 305: Checking Things Under The Hood
Checking Things Under the Hood Things that burn can get on hot engine parts and start a fire. These include liquids like fuel, oil, coolant, brake fluid, windshield washer and other fluids, and plastic or rubber. You or others could be burned. Be careful not to drop or spill things that will burn onto a hot engine.
Page 306 2. Then go to the front of the vehicle and release the secondary hood release. 3. Lift the hood; release the hood prop from its retainer and put the hood prop into the slot in the hood. 5-1 1...
Page 308 H. Radiator Pressure Cap A. Coolant Recovery Tank B. Engine Air CleanedFilter I. Engine Oil Fill Cap C. Windshield Washer Fluid Reservoir J. Remote Negative (-) Terminal Marked “GND” D. Engine Air Cleaner/Filter Indicator (If Equipped) K. Brake Master Cyiinder E.
Page 309 When you open the hood on the V8 engine, you’ll see the following: 5-1 4...
Page 310 Coolant Recovery Tank Engine Air Cleaner/Filter Windshield Washer Fluid Reservoir Engine Oil Dipstick Automatic Transmission Dipstick Engine Oil Fill Cap Radiator Pressure Cap Remote Negative (-) Terminal Marked “GND” Power Steering Fluid Reservoir Brake Master Cylinder Engine Compartment Fuse Block Battery Before closing the hood, be sure all filler caps are on properly.
Page 311 V8 Engine When to Add Engine.Oil If the oil is at or below the F mark for the L6 engine or the cross-hatched area at the tip of the dipstick for the V8 engine, then you’ll need to add at least one quart of oil. 5-1 6 The engine oil fill cap is located in the engine...
Page 312 What Kind of Engine Oil to Use Oils recommended for your vehicle can be identified by looking for the starburst symbol. This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Do not use any oil which does not carry this starburst symbol. If you choose to perform the engine oil change service yourself, be sure...
Page 313 As in the chart shown previously, SAE 5W-30 is the only viscosity grade recommended for your vehicle. You should look for and use only oils which have the API Starburst symbol and which are also identified as SAE 5W-30. If you cannot find such SAE 5W-30 oils, you can use an SAE 1OW-30 oil which has the API Starburst symbol, if it’s going to be 0°F (-18°C) or above.
Page 314 However, your engine oil and filter must be changed at least once a year and at this time the system must be reset. It is also important to check your oil regularly and keep it at the proper level. If the system is ever reset accidentally, you must change your oil at 3,000 miles (5 000 km) since your last oil change.
Page 315 Engine Air Cleaner/Filter The engine is located toward the front of the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on engine air cleaner filter location. 5-20 cleaner/filter The service window (A) with the percentage scale shows the amount of engine air cleaner/filter life used.
Page 316 To check or replace the engine air cleaner/filter, do the following: 1. Remove the three screws on the engine air cleaner/filter and lift off the cover. 2. Twist out the old engine air cleaner/filter and replace it with a new one, if needed. 3.
Page 317 How to Check Because this operation can be a little difficult, you may choose to have this done at the dealership service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. Notice: Too much or too little fluid can damage your transmission.
Page 318 Then, without shutting off the engine, follow these steps: The automatic transmission dipstick handle with the transmission and lock symbol is located in the engine compartment onthe passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location.
Page 319 Engine Coolant The cooling system in your vehicle is filled with DEX-COOL@ engine coolant. This coolant is designed to remain in your vehicle for 5 years or 150,000 miles (240 000 km), whichever occurs first, if you add only DEX-COOL@ extended life coolant. The following explains your cooling system and how to add coolant when it is low.
Page 320 Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you wouldn’t get the overheat warning.
Page 321 Adding Coolant If you need more coolant, add the proper DEX-COOL@ coolant mixture at the coolant recovery tank. Turning the radiator pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly.
Page 322 Engine Overheating You will find a coolant temperature gage on your vehicle’s instrument panel. If Steam Coming From Your Engine Steam from an overheated engine you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it.
Page 323 If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: Climb a long hill on a hot day. Stop after high-speed driving.
Page 324 Cooling System When you decide it’s safe to lift the hood, here’s what you’ll see: Engine V8 Engine A. Coolant Recovery Tank B. Radiator Pressure Cap C. Engine Fan If the coolant inside the coolant recovery tank is boiling, don’t do anything else until it cools down. The vehicle should be parked on a level surface.
Page 325 The coolant level should be at least up to the FULL COLD mark. If it isn’t, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system.
Page 326 How to Add Coolant to the Coolant Recovery Tank If you haven’t found a problem yet, but the coolant level isn’t at the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL@ engine coolant at the coolant recovery tank. See Engine Coolant on page 5-24 for more information.
Page 327 When the coolant in the coolant recovery tank is at the FULL COLD mark, start your vehicle. If the overheat warning continues, there’s one more thing you can try. You can add the proper coolant mixture directly to the radiator, but be sure the cooling system is cool before you do it.
Page 328 How to Add Coolant to the Radiator 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about one full turn. If you hear a hiss, wait for that to stop.
Page 329 3. Fill the radiator with the proper DEX-COOL@ coolant mixture, up the base of the filler neck. See Engine Coolant information about the proper coolant mixture. 5-34 4. Then fill the coolant recovery tank to the FULL COLD mark. page 5-24 for more Put the cap back on the coolant recovery tank, but leave the radiator pressure cap off.
Page 330 6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. 7. By this time, the coolant level inside the radiator filler neck may be lower. If the level is lower, add more of the proper DEX-COOL@ coolant mixture through the filler neck until the level reaches the base of the filler neck.
Page 331 Power Steering Fluid The power steering fluid reservoir is located in the engine compartment. is on the passenger’s side of vehicles with the L6 engine and is on the driver’s side of vehicles with the V8 engine. When to Check Power Steering Fluid is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise.
Page 332 Windshield Washer Fluid What to Use When you need windshield washer fluid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing.
Page 333 Brakes Brake Fluid Your brake master cylinder reservoir is filled with DOT-3 brake fluid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down. The first is that the brake fluid goes down to an acceptable level during normal brake lining wear.
Page 334 Checking Brake Fluid can check the brake fluid without taking off the cap. After work is done on the brake hydraulic system, make sure the level is above the MIN but not over the MAX mark. What to Add When you do need brake fluid, use only DOT-3 brake fluid.
Page 335 Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal firmly).
Page 336 Replacing Brake System Parts The braking system on a vehicle is complex. parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts.
Page 337 Vehicle Storage If you’re not going to drive your vehicle for 25 days or more, remove the black, negative (-) cable from the battery. This will help keep your battery from running down. Batteries have acid tnat can burn you and gas that can explode.
Page 338 Notice: Ignoring these steps could result in costly damage to your vehicle that wouldn’t be covered by your warranty. Trying to start your vehicle by pushing or pulling it won’t work, and it could damage your vehicle. 1. Check the other vehicle. must have a 12-volt battery with a negative ground system.
Page 339 Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You don’t need to add water to the ACDelco@ battery installed in your new vehicle.
Page 340 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Don’t let the other end ._ . _ . _ _,.-.. touch metal. Connect it to the positive (+) terminal of the good battery.
Page 341 8. Now connect the black negative (-) cable to the negative (-) terminal of the good battery. Use a remote negative (-) terminal if the vehicle has one. Don’t let the other end touch anything until the next step. The other end of the negative (-) cable doesn’t go to the dead battery.
Page 342 Jumper Cable Removal A. Heavy, Unpainted Metal Engine Part or Remote Negative (-) Terminal B. Good Battery or Remote Positive (+) and Remote Negative (-) Terminals C. Dead Battery or Remote Positive (+) Terminal To disconnect the jumper cables from both vehicles, do the following: 1.
Page 343: Rear Axle
Rear Axle When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant. How to Check Lubricant 5-48 To get an accurate reading, the vehicle should be on a level surface. The proper level is from 0 to 3/8 inch (0 to 10 mm) below the bottom of the filler plug hole.
Page 344: Four-Wheel Drive
Four-wheel Drive Lubricant checks in this section also apply to these vehicles. However, there are two additional systems that need lubrication. Transfer Case When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant. See Part Maintenance Inspections on page 6-15.
Page 345 Front Axle When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. How to Check Lubricant 5-50 To get an accurate reading, the vehicle should be on a level surface.
Page 346: Bulb Replacement
Bulb Replacement For the type of bulbs, see Replacement Bulbs on page 5-52. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs Halogen bulbs ha pressurized gas can burst if you drop or scratch the bulb. You or others could be injured.
Page 347 3. Pull the assembly away from the vehicle. 4. Unclip the wiring harness (A) and remove the three socket retaining screws (B). 5. Remove the socket by releasing the retaining tabs. 6. Holding the socket, pull the bulb to release it from the socket.
Page 348: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at leasi twice a year for wear or cracking. See Normal Maintenance Replacement Parts on page 5-106 for the proper type of replacement blade. Notice: Use care when removing or installing a blade assembly.
Page 349 2. Press down on the blade assembly pivot locking tab. Pull down on the blade assembly to release it from the wiper arm hook. 3. Remove the insert from the blade assembly. The insert has two notches at one end that are locked by the bottom claws of the blade assembly.
Page 350 A. Claw in Notch B. Correct Installation C. Incorrect Installation 6. Put the blade assembly pivot in the wiper arm hook. Pull up until the pivot locking tab locks in the hook slot. 7. Carefully lower the wiper arm and blade assembly onto the windshield.
Page 351: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your Warranty booklet for details. Poorly maintained and properly used tires are dangerous.
Page 352 Inflation Tire Pressure The Certificationflire label, which is on the driver’s door edge, above the door latch, shows the correct inflation pressures for your tires when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km).
Page 353 Tire Inspection and Rotation Tires should be rotated every 7,500 miles (12 500 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-59 and Wheel Replacement...
Page 354 Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust places where the wheel attaches to the vehicle.
Page 355 Buying New Tires To find out what kind and size of tires you need, at the Certificationnire label. The tires installed on your vehicle when it was new had a Tire Performance Criteria Specification (TPC Spec) number on each tire’s sidewall. When you get new tires, get ones with that same TPC Spec number.
Page 356 Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance.
Page 357 Temperature A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 359 Tire Chains Di-..’t use tire chains. There’s not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control vehicle and you or others may be injured in crash.
Page 360 The air inflator kit may be located in the glove box. The kit includes a 22 ft (6.7 m) hose with three nozzle adapters. To use the air inflator, attach the appropriate nozzle adapter to the end of the hose if required. Then attach that end of the hose to the object you wish to inflate.
Page 361 If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout”, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side.
Page 362 4. Turn off engine. 5. Put the wheel blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire on the other side of the vehicle, at the opposite end. The following steps will tell you how to use the jack and...
Page 363 Removing the Spare Tire and Tools Envoy 5-68 Envoy XL will The jacking equipment you need is stored under the rear seat in the Envoy or in the left rear quarter panel storage compartment in the Envoy XL. See Rear Seat Operation on page 1-6 for more information.
Page 364 : - i The tools you'll be using include the wheel wrench (A), tire blocks (B), extension(s) (socket end) (C), handle (jack end) (D), and jack (E). The Envoy XL will include an additional extension. The following instructions explain how to remove the spare tire mounted underneath your vehicle.
Page 365 2. Turn the wheel wrench counterclockwise to lower the spare tire. Keep turning the wheel wrench until the spare tire can be pulled out from under the vehicle. If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower.
Page 366 Secondary Latch System Your vehicle has an underbody mounted tire hoist assembly equipped with a secondary latch system. It’s designed to stop the spare or flat road tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the spare tire must be stored with the valve stem pointing up.
Page 367 2. If it is not visible, proceed to Step 6. If visible, first try to tighten the cable by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice. You cannot overtighten the cable. 3. Loosen the cable by turning the wheel wrench counterclockwise three or four turns.
Page 368 9. Lower the jack by turning the wheel wrench counterclockwise. Keep lowering the jack until the spare tire slides off the jack or is hanging by the cable. 10. Disconnect the jack handle from the jack and carefully remove the jack. Use one hand to push against the spare while firmly pulling the jack out from under the spare tire with the other hand.
Page 369 Removing the Flat Tire and Installing the Spare Tire 1. Using the wheel wrench, loosen all the wheel nuts. Don’t remove them yet. 2. Turn the jack adjusting knob clockwise by hand to raise the jack lift head. 5-74 3. Place the handle. extension and wheel wrench onto the jack.
Page 370 Rear A. Frame B. Jack C. Handle D. Extension(s) E. Wheel Wrench 4. Place the jack in the appropriate position nearest the flat tire. Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed.
Page 371 5. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground so there enough room for the spare tire to fit. 6. Remove all the wheel nuts and take off the flat 5-76 Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time.
Page 372 Never use or grease on studs or nuts. do, the nuts might come loose. Your wheel could fall off, causing a serious accident. 8. Place the spare on the wheel mounting surface. 9. Put the nuts on by hand. Make sure the rounded end is toward the wheel 10.
Page 373 12. Use the wrench to tighten the wheel nuts firmly in a crisscross sequence as shown. Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident.
Page 374 Storing a Flat or Spare Tire and Tools Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. The underbody-mounted spare tire needs to be stored with the valve stem pointing If the spare tire is stored with the valve stem...
Page 375 Follow this diagram to store the underbody-mounted spare. A. Wheel Wrench B. Hoist Shaft C. Extension(s) D. Retainer E. Spare or Flat Tire (Valve Stem Pointed Up) 1. Put the tire on the ground at the rear with the valve stem pointed up and to the rear. 2.
Page 376 Return the jack, wheel wrench and wheel blocks to the proper location in the vehicle. Roll up the instruction label and return to the slot in the tool kit. Envoy XL A. Handle B. Wheel Wrench C. Extension(s) D. Wheel Blocks and Jack 5-81...
Page 377: Appearance Care
Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into flames if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space.
Page 378 Here are some cleaning tips: Always read the instructions on the cleaner label. Clean up stains as soon as you can they set. Carefully scrape off any excess stain. Use a clean cloth or sponge, and change to a clean area often.
Page 379 Vinyl Use warm water and a clean cloth. Rub with a clean, damp cloth to remove din. You may have to do this more than once. Things like tar, asphalt and shoe polish will stain if you don’t get them off quickly. Use a clean cloth and vinyl/leather cleaner.
Page 380 Care of Safety Belts Keep belts clean and dry. or : e safety bt it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water. Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak.
Page 381 Cleaning Exterior LampdLenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing Your Vehicle.” Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish.
Page 382 Windshield, Backglass and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper biade chatters when running, wax, sap or other material may be on the blade or windshield. Clean the outside of the windshield with a full-strength glass cleaning liquid.
Page 383 Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials avaliable from your dealer or other service outlets.
Page 384 GM Vehicle Care/Appearance Materials Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Oil Removes tar, road oil Remover and asphalt. ~~~~~~~~ Chrome Cleaner and Use on chrome or Polish stainless steel. White Sidewall Tire Removes soil and black Cleaner marks from whitewalls.
Page 385: Vehicle Identification
Vehicle Identification Vehicle Identification Number (VIN) SAMPLE4UXl M072675 This is the legal identifier for your vehicle. a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates title and registration.
Page 386: Electrical System
Electrical System Add-on Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 387 Power Windows and Other Power Options Circuit breakers protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed or goes away. Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit...
Page 388 Engine Compartment Fuse Block The fuse block is located under the hood in the engine compartment on the driver’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. Remove the primary cover by pressing the two locking tabs.
Page 390 Usage Electrically-Controlled Air Suspension Passenger’s Side High-Beam Headlamp Passenger’s Side Low-Beam Headlamp Back-Up-Trailer Lamps Driver’s Side High-Beam Headlamp Driver’s Side Low-Beam Headlamp Fog Lamps Stop Lamp Cigarette Lighter lqnition Coils Suspension Ride TBD-Ignition 1 Air Baa Brake Electric 5-95...
Page 391 Fuses Ignition A Blower Motor Ignition B Passenger’s Side Trailer Turn Driver’s Side Trailer Turn Hazard Flashers Relays Blank Rear Window Fog Lamps Horn 5-96 Fuses Usage Miscellaneous Washer Usage Fuel Pump Windshield WipersANasher High-Beam Headlamp Air Conditionina Cooling Fan Headlamp Driver Module Starter Usage...
Page 393 Fuses Electrically-Controlled Air Suspension Passenger’s Side High-Beam Headlamp Passenger’s Side Low-Beam Headlamp Back-Up-Trailer Lamps Driver’s Side High-Beam Headlamp Driver’s Side Low-Beam Headlamp WASH Automatic Transfer Case Windshield Wipers Powertrain Control Module B Lamps Stop Lamp Cigarette Lighter lqnition Coils Cannister Vent TBD-Ignition 1 Crank Air Bag...
Page 394 Headlamp Washer Rear Window Washer Fog Lamps Horn Fuel Pump Windshield Wiperswasher High-Beam Headlamp Air Conditioning Cooling Fan 46 Headlamp Driver Module Starter Ignition 1 Miscellaneous Usage Instrument Panel Battery Rear Underseat Fuse Block L6 Engine 5-99...
Page 395 CLOCKS) 2 3 m 2 4 UNLOCK PARK Envoy 5-1 00 Fuses Usage Right Door Control Module Left Door Control Module Liftgate Module 2 Bodv Truck Controller 3 Rear Fog Lamps Liftaate Module/Driver Seat Module Body Truck Controller 2 Power Seats Blank Driver Door Module...
Page 396 Fuses Usage Blank UNLOCK Blank RainsenseTM Wipers Parking Lamps Truck Body Controller 4 Cruise Control 32 Truck Bodv Controller 5 Front Wipers Vehicle STOP Blank Heat Ventilation Air Conditioninq B Front Parking Lamps Left Turn Signal Fuses Heat Ventilation Air Conditionina 1 Truck Bodv Controller 4 Trailer Park Right Turn Signal...
Page 397 PARK LP Envoy XL 5-1 02 G,D,w) 4 o T B c 4 ) Truck Body Controller 3 Rear Foa Lamps Liftgate Module/Driver Seat Module Truck Body Controller 2 Power Seats Rear WiPer Driver Door Module Amplifier Passenger Door Module Rear Climate Controls Left Rear Parking Lamps Auxiliarv Power 2...
Page 398 Fuses Usage Retained Accessorv Power Blank UNLOCK Blank Blank OH Battery/OnStar@ System Sunroof RainsenseTM Wipers Parking Lamps Truck Body Controller 4 Cruise Control Truck Body Controller 5 Front WiDers Vehicle STOP Blank Heat Ventilation Air Conditioning B Front Parking Lamps Fuses Left Turn Siqnal Heat Ventilation Air Conditioning 1...
Page 399 Capacities and Specifications Engine “VORTECTM 4200 L6 ” “VORTECTM 5300 V8 ” Application Wheel Nut Torque 5- 1 04 VIN Code Transmission L6 Engine Metric English 100 Ib ft 140 N-m Spark Plug Gap Firing Order 0.042 inches 1-5-3-6-2-4 (1.07 0.060 inches 1-8-7-2-6-5-4-3 (1.52 mm)
Page 400 Differential Fluid Rear Front Fuel Tank Envoy with Envoy RPO NNK Envoy XL All capacities are approximate. When adding, be sure to fill to the appropriate level, as recommended in this manual. Recheck the fluid level after filling. L6 Engine 4.0 pints 1.9 L 2.6 pints...
Page 401 Normal Maintenance Replacement Parts Engine Oil Filter Engine Air Cleaner Automatic Transmission Filter Kit Spark Plugs Fuel Filter Windshield Wiper Blade Backglass Wiper Blade *ACDelco@ part number 5-1 06 Part Number PF58" P F44* A201 4C* GM Part No. 24200796 41 -981 41 -974* G F831*...
Page 402 Section 6 Maintenance Schedule Introduction ... Your Vehicle and the Environment ... Maintenance Requirements ... How This Section is Organized ... Part A: Scheduled Maintenance Services ... 6. 4 Using Your Maintenance Schedule ... Scheduled Maintenance Part B: Owner Checks and Services ... 6.10 At Each Fuel Fill At Least Once a Month At Least Twice a Year ...
Page 403 Maintenance Schedule Introduction IMPORTANT: KEEP ENGINE OIL AT THE PROPER LEVEL AND CHANGE AS RECOMMENDED Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the...
Page 404 How This Section is Organized This maintenance schedule is divided into five parts: “Part A: Scheduled Maintenance Services” explains what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your dealer’s service department or another qualified service center do these jobs.
Page 405 Part A: Scheduled Maintenance Services This part contains engine oil scheduled maintenance which explains the engine oil life system and how it indicates when to change the engine oil and filter. Also, listed are scheduled maintenance services which are to be performed at the mileage intervals specified. Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition.
Page 406 Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles (166 000 km) at the same intervals for the life this vehicle. The services shown at 150,000 miles (240 000 km) should be repeated at the same interval after 150,000 miles (240 000 km) for the life of this vehicle.
Page 407 7,500 Miles (12 0 Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. Rotate tires. See Tire lnspection and Rotation on page 5-58 for proper rotation pattern and additional information. (See footnote +.) 15,000 Miles (25 000 Inspect engine air cleaner filter if you are driving...
Page 408 45,000 Miles (75 000 km) Inspect engine air cleaner filter if you are driving in dusty conditions. Replace filter if necessary. An Emission Control Service. (See footnote Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking.
Page 409 67,500 Miles (1 12 Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. CI Rotate tires. See Tire lnspection and Rotation on page 5-58 for proper rotation pattern and additional information.
Page 410 100,000 Miles (166 000 km) V8 Engine Only: Inspect spark plug wires. An Emission Control Service. Replace spark plugs. An Emission Control Service. 0 Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: In heavy city traffic where the outside temperature regularly reaches 90°F (32°C)
Page 411 Part B: Owner Checks and Services Listed in this part are owner checks and services which should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Part D.
Page 412 At Least Twice a Year Restraint System Check Make sure the safety belt reminder iight and aii your beits, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 413 At Least Once a Year Key Lock Cylinders Service Lubricate the key lock cylinders with the lubricant specified in Part D. Body Lubrication Service Lubricate all hood latch assembly, secondary latch, pivots, spring anchor, release pawl, rear compartment hinges, outer liftgate handle pivot points, rear door detent link, roller mechanism, liftgate handle pivot points, latch bolt, fuel door hinge, cargo door hinge, locks and folding seat hardware.
Page 414 Automatic Transmission Shift Lock Ccntrol Sy-+er CheP When you are doing this check, the vehicle could move suddenly. If it does, you or others could be injured. Follow the steps below. Before you start, be sure you have enough room around the vehicle.
Page 415 Parking Brake and Automatic Transmission Park (P) Mechanism Check WI .___ ou are doing check, your vehicle ’_. could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll.
Page 416 Part C: Periodic Maintenance Inspections Listed in this part are inspections and services which should be performed at least twice a year (for instance, each spring and fall). You should let your dealer’s service department or other qualified service center do these jobs.
Page 417 Engine Cooling System Inspection Inspect the hoses and have them replaced if they are cracked, swollen or deteriorated. Inspect all pipes. fittings and clamps; replace as needed. Clean the outside of the radiator and air conditioning condenser. To help ensure proper operation, a pressure test of the cooling system and pressure cap is recommended at least once a year.
Page 418 Part D: Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer. Usage Gasoline Engines starburst symbol Engine Oil of the proper viscosity. To determine the preferred viscosity for your vehicle's engine, see Daae 5- 15.
Page 419 Fluid/Lubricant Usage AUTO-TRAK II Fluid (GM Part No. U.S. 12378508, in Canada Transfer Case 1 0953626). Chassis Lubricant (GM Part No. Rear Driveline U.S. 12377985, in Canada Center Spline 88901242, or equivalent) or lubricant and Universal meeting requirements of NLGI #2, Joints Category LB or GC-LB.
Page 420 Part E: Maintenance Record After the scheduled services are performed, record the date, odometer reading and who performed the service and any additional information from “Owner Checks and Services” “Periodic Maintenance” on the following record pages. Also, you should retain all maintenance receipts. Maintenance Record 6-1 9...
Page 421 Maintenance Record kont’d) 6-20...
Page 422 Maintenance Record (cont’d) 6-2 1...
Page 423 Maintenance Record (cont’d) Odometer Date Serviced By Maintenance Record Reading 6-22...
Page 424: Customer Assistance Information
Section 7 Customer Assistance Information ... Customer Satisfaction Procedure ... Online Owner Center Customer Assistance for Text Telephone (TTY) Users ... Customer Assistance Off ices ... GM Mobility Program for Persons with Disabilities ... Roadside Assistance Program ... Courtesy Transportation Customer Assistance Information Reporting Safety Defects Reporting Safety Defects to the United States...
Page 425 Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to GMC. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best...
Page 426 The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. Although you may be required to resort to this informal dispute resolution program prior to filling out a court action, use of the program is free of charge and your case will generally be heard within...
Page 427 Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use the Text Telephones (TTYs), GMC has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with GMC by dialing: 1 -800-GMC-8583 (462-8583).
Page 428 Roadside Assistance Program GMC’s Roadside Assistance Provides stranded owners with over-the-phone roadside repairs, location of the nearest GMC dealer or the following special services: Flat Tire Change: Installation of spare tire will be covered at no charge (customer is responsible for repair or replacement of tire).
Page 429 Maps include points of interest and a list of GMC dealers along the route. Also included is a list of hotels along the route that are discounted through affiliation with “Quest International.”...
Page 430 Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, GMC helps minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following:...
Page 431 Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, reimbursement up to $30 per day (five days maximum) may be available for the use of public transportation such as taxi or bus. In addition, should you arrange transportation through a friend or relative, reimbursement for reasonable fuel expenses up to $10 per day (five day maximum) may be available.
Page 432: Reporting Safety Defects
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying General Motors.
Page 433 Reporting Safety Defects to General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you’ll notify us. Please call us at 1 -800-GMC-8782 (1 -800-462-8782), or write: Pontiac-GMC Customer Assistance Center P.O. Box 33172...
Page 434 Service Bulletins Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. In Canada, information pertaining to Product Service Bulletins can be obtained by contacting your General Motors dealer or by calling 1-800-GM-DRIVE (1 -800-463-7483).
Page 436 Accessory Inflator Accessory Power Outlets ... Adding Snow Plow or Similar Equipment Adding Washer Fluid ... Additional Program Information ... Additives, Fuel ... Add-on Electrical Equipment ... Adjusting the Speakers (Balance/Fade) ..3-66, 3-74, Air Bag Readiness Light Air Bag Systems How Does an Air Bag Restrain? ...
Page 437 Automatic Transmission Fluid ... Operation ... Automatic Transmission Check ... Automatic Transmission Shift Lock Control System Check Backglass Wiper Blade Replacement Backing Up ... Battery ... BATTERY NOT CHARGING ... Battery Replacement ... Battery Run-Down Protection Before Leaving on a Long Trip ... Before You Drive Body Lubrication Service ...
Page 438 Check Engine Light Gages Warning Light CHECK WASHER FLUID Checking Brake Fluid Checking Coolant ... Checking Engine Oil ... Checking Things Under the Hood ... Checking Your Restraint Systems Chemical Paint Spotting Child Restraints Center Seat Position Child Restraint Systems ... Infants and Young Children ...
Page 439 Customer Assistance Information Courtesy Transportation ... Customer Assistance for Text Telephone (TTY) Users ... Customer Assistance Offices ... Customer Satisfaction Procedure ....7-2 GM Mobility Program for Persons with Disabilities ...
Page 440 Electrical System Add-on Equipment ... Fuses and Circuit Breakers Headlamps ... Power Windows and Other Power Windshield Wiper Fuses ... Electronically Controlled Air Suspension System Emergency Release for Opening Emissions Inspection and Maintenance Programs ... Engine Air Cleaner/Filter ... Battery ... Change Engine Oil Light ...
Page 441 Fluid Automatic Transmission ... Power Steering ... Windshield Washer ... FM ... Fog Lamps Following Distance Footnotes Four-wheel Drive ... Front Axle ... Front Storage Area Fuel ... Addltwes California Fuel ... Filling a Portable Fuel Container ... Filling Your Tank Fuels in Foreign Countries ...
Page 442 Headlamps Bulb Replacement ... Electrical System ... Front Turn Signal and Sidemarker Lamps H ~ O C J ~ R B~llbs ... Headphones ... Heated Seats ... Highway Hypnosis ... Hill and Mountain Roads ... Hitches ... HomeLink Transmitter, Programming HomeLink@ Transmitter Hood Checking Things Under...
Page 443 Instrument Panel Brightness ... Interior Lamps Interior Plastic Components ... Jump Starting ... Key Lock Cylinders Service ... Keyless Entry System ... Keys ... Lamps Exterior ... Interior ... Lamps On Reminder ... Lap-Shoulder Belt ... LATCH System Child Restraints ... Securing a Child Restraint Designed for the LATCH System Leather ...
Page 444 Locks (cont.) Power Door ... Programmable Automatic Door Locks Rear Door Security Locks ... Loss of Control ... Low Fuel Warning Light Luggage Carrier ... Lumbar Power Controls Maintenance. Normal Replacement Parts ... 5-1 06 Maintenance Schedule At Each Fuel Fill At Least Once a Month ...
Page 445 New Vehicle Break-In ... Normal Maintenance Replacement Parts Odometer ... Off-Road Recovery ... Change Engine Oil Light ... Engine ... Pressure Gage ... OIL PRESSURE LOW/STOP ENGINE ... 3-60 Older Children, Restraints ... Online Owner Center ... Onstar@ System ... Onstar@ Personal Calling Onstar@ Services ...
Page 446 Personalization ... Personalization. Climate Controls ... Plan Ahead When Possible ... Playing a Cassette Tape ... Playing a Compact Disc Playing a Specific Loaded Compact Disc ... Playing the Radio Power Accessory Outlets ... Door Locks ... Electrical System ... Lumbar Controls ...
Page 447 Rear Seat Entertainment System Rear Seat Operation ... Rear Seat Passenger Positions Rear Seat Passengers, Safety Belts ... 1-23 Rear Seats (Envoy XL) ... Rear Underseat Fuse Block ... Rear Window Defogger ... Rearview Mirror, Automatic Dimming with OnStarB and Compass ... Reclining Seatbacks, Power ...
Page 448 Safety Belts (cont.) Passengers Seat Rear Right Front Passenger Position Safety Belt Extender Safety Belt Use During Pregnancy ... 1-22 Safety Belts Are for Everyone ... Safety Chains ... Safety Warnings and Symbols ... Scheduled Maintenance ... Seats Head Restraints ... Heated Seats ...
Page 449 Steering. Suspension and Front Drive Axle Boot and Seal Inspection ... Steering Tips ... Steering Wheel Comfort Controls ... Steering Wheel Controls, Audio ... Stereo RCA Jacks ... Storage Areas Convenience Net ... Front Storage Area ... Glove Box ... Luggage Carrier ...
Page 450 Transfer Case ... Transfer Case and Front Axle (Four-wheel Drive) Inspection ... Transmission Fluid, Automatic ... Transmission Operation, Automatic Transmission. Transaxle. Transfer Case Unit Repair Manual Transportation Options ... Travel Note Recorder Trip Information ... Trip Odometer ... Turn and Lane Change Signals ... TURN SIGNAL ON ...
Page 451 Weatherstrip Lubrication ... Weight of the Trailer Weight of the Trailer Tongue ... What Kind of Engine Oil to Use ... What to Add ... What to Do with Used Oil ... What to Use ... Wheels Alignment and Tire Balance Replacement ...
Page 455 NOTES . &...
Page 457 NOTES -&...

GMC 2003 Envoy XL Owner's Manual

Quick Links

Related Manuals for GMC 2003 Envoy XL

Summary of Contents for GMC 2003 Envoy XL

Table of Contents