Table of Contents
Advertisement
Available languages
Available languages
Operating the appliance
These instructions apply to several appliance variants. It is
possible that individual features are described which do not
apply to your appliance.
Note: Switch on the extractor hood when you start cooking and
switch it off again several minutes after you have finished
cooking. This is the most effective way of removing the kitchen
fumes.
Control panel
Explanation
1
Switch the fan on/off
2
Switch the fan setting up
3
Display panel
4
Switch on the lighting
5
Switch on the fan run-on
Setting the fan
Note: Always adjust the fan strength to meet current conditions.
If there is a large build-up of steam or fumes, select a high fan
setting.
Switching on the appliance
Press the
button.
#
1.
Fan setting 1 is set.
Press the
button until the required fan setting is set.
a
2.
The set fan setting is shown in the display panel. After the
intensive setting, fan setting 1 is set.
Switching off the appliance
Press the 0 button.
Intensive setting
You can use the intensive setting if there is a large build-up of
odours and fumes/vapours.
Press the
button until fan setting 4 is displayed in the
a
1.
display panel.
The intensive setting is activated.
Press the
button until fan setting 1 is displayed in the
a
2.
display panel.
The intensive setting is deactivated and fan setting 1 is set.
Note: The running time of the intensive setting is 5 minutes.
Once this time has elapsed, the appliance switches back to fan
setting 2.
Fan run-on time
The duration of the run-on time depends on the fan setting that
is set:
Fan setting 1: 20 minutes
■
Fan setting 2: 15 minutes
■
Fan setting 3: 10 minutes
■
Intensive setting: 5 minutes
■
6
Select the fan setting.
1.
Press the
button.
0
2.
The fan runs at the set fan setting. The indicator beside the
set fan setting flashes. The ventilation automatically switches
off once the run-on time has elapsed.
Press the
button.
a
3.
The fan run-on ends before the remaining run-on time
elapses. Ventilation continues at the set fan setting.
Press the
0
or
#
button.
4.
The fan run-on ends before the remaining run-on time
elapses. The ventilation is switched off.
Lighting
The lighting can be switched on and off independently of the
ventilation.
Press the
button.
B
Saturation display
If the metal grease filter and the activated charcoal filter are
saturated, the following numbers flash:
Metal grease filter:
‚
■
Activated charcoal filter:
■
Metal grease filter and activated charcoal filter:
■
flash alternately
When this happens, do not delay cleaning the metal grease
filter or replacing the activated charcoal filter any further.
For instructions on how to clean the metal grease filter, refer to
the section Cleaning and maintenance.
Resetting a saturation indicator
Press and hold the
#
button until the saturation indicator no
longer flashes.
The saturation indicator is reset.
Resetting the saturation displays
Press and hold the
button until the saturation indicator for
#
1.
the metal grease filter no longer flashes.
The saturation indicator for the metal grease filter is reset.
Press and hold the
button until the saturation indicator for
#
2.
the activated charcoal filter no longer flashes.
The saturation indicator for the activated charcoal filter is
reset.
Switching over the display for circulating-air mode
For circulating-air mode, the electronic control display must be
switched over accordingly:
Check that the extractor hood is connected and switched off.
1.
Press the
and
buttons at the same time until the
a
B
2.
numbers
and
flash alternately.
‚
ƒ
The electronic control is switched over to circulating-air
mode.
Switching over the display for exhaust air mode
Check that the extractor hood is connected and switched off.
1.
Press the
and
buttons at the same time until the
a
B
2.
number
flashes.
‚
The electronic control is switched back to exhaust-air mode.
ƒ
‚
and
ƒ
Advertisement
Chapters
Table of Contents
