Subscribe to Our Youtube Channel
Related Manuals for Arcora BLANCUS 45
Summary of Contents for Arcora BLANCUS 45
- Page 1 BLANCUS 45 Manual Use Please read this manual carefully before using the product .
- Page 2 BLANCUS 45. INTRODUCTION BLANCUS 45 Micro Automatic Floor Scrubber is a machine which uses the mechanical movement of the disc brush and the chemical action of water and detergent solution to clean the hard floor with various stains and at the same...
-
Page 3: Working Width
● The operator must use it in the appropriate application area (cleaning the hard floor) when operating the scrubber. ● Pay attention to obstacles in the workplace, such as stairs, shelves, etc.,and pay attention to the surrounding people, especially children. ●... - Page 4 Disc brush diameter 22.8cm Disc brush rotation rate 200rpm Disc brush motor 2*200W Disc brush pressure 20kg Water absorption motor 200W Vacuum degree 120mbar Turning radius 30cm Clean water tank capacity 3.5L Sewage tank capacity Noise level 75dB 2*8.8Ah-24V (Lithium battery) Battery pack Battery weight 1.9*2kg...
- Page 5 4.0 THE PACKAGE OF THE MACHINE Packing size is as follows： length：1275mm width： 600mm height： 450mm...
- Page 6 5.0 STRUCTURE 1.Water suction switch 2.battery indicator 3.Disc brush switch 4.Overload reset button 5.Power switch 6.Screw 7. Sewage tank cover 8. Sewage tank 9.Right battery 10.Right battery 11.Upright trigger lock 12.Water valve switch 13. Charging socket 14. Clean water tank lock 15.
- Page 7 6.0INSTRUCTIONS FOR USE 6-1 The description picture of disc brush installation：picture 6-1 1. According to step 1 in the picture, press the disc brush to the positive drive buckle to the end. 2. Rotate the two disc brushes in the direction of step 2 in the picture to fasten the disc brush .
- Page 8 description picture of filling the water ： Picture 6-3- （ 1） ~ (3) 1. As shown in step 1 of Figure 6-3-(1), push the lock of the clean water tank to the inside. 6-3-（1） 6-3-（2） 6-3-（3） 2. Lift the clean water tank up as shown in step Figure...
- Page 9 6-4The description picture of disassembling sewage tank ： Picture 6-4-（1）-（2） 1. Move the sewage tank swing buckle up as shown in Figure 6-4-(1). 2. As shown in Figure 6-4-(2), the upper end of the sewage tank is opened outwards,and then remove the tank from the joint.
- Page 10 6-6 The description picture of control panel：picture 6-6 1.Disc brush motor overload protection button 2.Power switch 3.Water suction motor overload protection button 4.Disc brush switch 5.Battery indicator (red, yellow, green) Description：When the red, yellow, and green indicators are on, it indicates that the battery is fully charged.
- Page 11 图 6-6 6-8 Battery charging： ATTENTION：A battery charger approved and supplied by the company must be used (picture 6-8).Using an incompatible charger may result in damage to the battery and may result in fire. Two batteries must be charged together during charging.
-
Page 12: Maintenance
5.The charger will automatically start charging, charging time is about 1 hour and 40 minutes. 6.After the end of the charging cycle, unplug the AC power cord from the outlet first and then unplug the DC charging plug from the machine. 7.0 MAINTENANCE 1、Daily maintenance （1）... - Page 13 （4）Please drain the sewage tank and the clean water tank before storing the machine. 8.0 Common faults and solutions Faults Cause Analysis Solutions Did not turn on the power switch Please turn on the power switch The battery is low and needs to be Please charge the battery The machine can't run charged...
- Page 14 The suction pipe is not reliably Reliably connect the suction connected to the water scraper pipe component Water suction pipe blocked Clear the blockage Poor water suction Suction pipe damage Replace the suction pipe performance The sewage tank cover is not Cover the sewage tank cover covered Sewage tank cover seal is damaged...
- Page 15 Name Name Button switch Upper handle case M3 nuts Charging plug M3X20 Pan head Lower handle case screws 4X30 Pan head tapping M6X20 Cylindrical screws head screws...
- Page 16 Handle connector Handle connector （back） （front） M6X20Cylindrical head 4X10 Pan head tapping screws screw Relay 4X10 Pan head tapping screws Circuit board Overload protector Power switch Water valve switch...
- Page 17 Name Numb Name Numb Name Aluminum tube 50X3Aluminum tube Joint rear plate sealing part handle Suction pipe upper M6X16 Cylindrical Clean water tank joint head screw lock 4X20 Countersunk Water tank pallet Silicone Case head tapping screws Conversion quick Aluminum pipe M6X16 Cylindrical...
- Page 18 connector connector head screws Water pipe Water suction motor 4X20 Pan head cover tapping screws Silencer Sponge Motor air guiding Silencer Sponge Cover shell Water suction motor Water suction motor 4X16 pan head exhaust hood tapping screw Motor air guide cover 3X12 pan head Circuit board cooling tapping screw...
- Page 19 Number Name Number Name Number Name Water tank cover Water tank cover Water tank cover lug lug screw A hanger screw A Threaded tank Clean water tank Threaded tank cover cover Water tank spool O-ring 11X3 O-ring 28X3 Water tank valve 4X20 Countersunk Water tank valve...
- Page 20 housing head tapping screws outer seal Tank swing buckle Tank swing buckle Tank swing buckle • screw spring Suction elbow for 3X12 countersunk Bottom cover sewage tank head tapping screw float ball cover Floating ball cap Sewage tank cover Sewage tank cover seal strip Sewage tank...
- Page 21 Number Name Number Name Right battery case upper cover Batteries 3X16 Pan head tapping screws 4X50 Pan head tapping screws Springs Battery pull buckles Battery buckles Battery plug copper parts Battery plugs Right battery case lower cover 4X70 Pan head tapping screw Left battery case lower cover Left battery case upper cover...
- Page 22 Number Name Number Name Machine fixing buckle 2.5X12 cotter pin Machine lock lever Disc brush motor cover Battery inserting pieces Battery insert plates 4X16 Pan head tapping Water pipe screws Motor cover bottom cover 4X20 Pan head tapping screws The electromagnetic valve 3X10 Pan head tapping screw Solenoid valve fittings...
- Page 23 Number Name Number Name 4X16 Pan head tapping Parabolic squeegee components screws Positioning components M4X20 Pan head screws M6 lock nuts 12X6 Flat pads 606 Bearings 40MM Parabolic squeegee wheels Bushings M6X25 Cylindrical head screws Parabolic squeegee rear Parabolic squeegee inner part strip Parabolic squeegee front Parabolic squeegee case...
- Page 24 Number Name Number Name Motor controller fixed Motor Controller plates M3 nuts M3X20 Pan head screws Disc brush cover Disc brush motors Drive buckles Motor cover connecting...
-
Page 25: Invoice Number
Parts M4X20 Pan head tapping 12X6 Flat pads screws Spring pads M6X25 Cylindrical head screws Disc brushes Drive buckle plates 5X16 Pan head tapping M5X12 Cylindrical head screw screws Water pipe quick connector Series product warranty card Card Number： Customer Name： Contact Number：... - Page 26 Distributor (official seal) 1. This warranty card must be stamped with the official seal of the distributor. 2. This warranty card is in duplicate, one for customer and one for agent distributor。 ★This card and the purchasing invoice are both considered as the protection to fix warranties,so please reserve them carefully.
- Page 27 Distributor (official seal) 3. This warranty card must be stamped with the official seal of the distributor. 4. This warranty card is in duplicate, one for customer and one for agent distributor。 ★This card and the purchasing invoice are both considered as the protection to fix warranties,so please reserve them carefully.
Need help?
Do you have a question about the BLANCUS 45 and is the answer not in the manual?
Questions and answers