Sony KDS-R50XBR1 Quick Setup Manual

2-637-152-11(1)
KDS-R50XBR1
KDS-R60XBR1

Quick Setup Guide

For further information, see the operating instruction supplied with the TV.
Please retain this guide for your future reference.
Please follow these steps to setup your TV:
1 Connecting Your TV
(See reverse side)
2 Running Initial Setup
3
Programming
the Remote Control
For service and technical assistance, call our Customer Information Service Center (Toll Free):
US residents: 1-800-222-SONY (7669) or visit http://www.sonystyle.com/tv/
Canadian residents: 1-877-899-SONY (7669) or visit http://www.sonystyle.ca/tv/
DO NOT RETURN TO THE STORE
Sony Corporation © 2005
Printed in Japan
2
Running Initial Setup
1
Press to turn on the TV.
The Initial Setup screen appears.
2
Press V or v to highlight the on-screen
display language. Then press .
The message "First please connect
cable/antenna" appears. This may require 50+ minutes for
completion and "Start auto program now?" appears.
3
Press (Yes) to start Initial Setup.
Initial Setup automatically creates a list of
receivable channels from both VHF/UHF
antenna and cable TV channels if both
sources are connected.
When Initial Setup is complete, the TV
will display the total number of analog channels and the total
number of digital channels found.
4
Press to exit this screen.
To run Auto Program again at a later time
Refer to the manual on "Initial Setup" and "Auto Program" sections.
1
Connecting Your TV
Making Audio/Video Connections
Your new TV includes various types of video inputs and two types
of audio jacks; composite-RCA type and digital audio (optical).
Use the outputs/inputs that are available on your components that
provide the best video/audio performances:
Best Audio/Video
Performance
Connector type
Connector type
PCM/DOLBY DIGITAL HDMI
Digital Optical
DIGITAL
AUDIO
(OPTICAL
OUT) (High-Definition Multimedia
Digital Coaxial
Interface)
Will require an adapter
DVI
(Digital Visual Interface)
to connect to this TV's
digital audio input. Will require an adapter to connect to this TV.
Analog Audio
Component video
S VIDEO
Composite video
RF/Coaxial
Activating CableCARD™ Service
Before you can use CableCARD service, you need to insert the
CableCARD device (supplied by your cable provider) and activate
the service.
Inserting the CableCARD incorrectly may result in permanent damage to the card and
the TV.
The connection diagrams shown on the reverse side are
recommendations only; other possible solutions may
exist. Connections that include an AV receiver can often
be complex, so check your AV receiver's instruction
manual for additional details.
See the "Cables Required" chart that appears with the
diagram to determine which cables you'll need.
Depending on the components you plan to connect, you
may need to purchase extra cables.
3

Programming the Remote Control

The remote control is preset to operate Sony brand video equipment.
Sony Equipment Programmable Code Number
DVD/VCR 751 (Sony Dream System)
SAT/CABLE 801 (Sony Satellite Receiver)
i.LINK 901 (Sony DVD Player (i.LINK))
If you have video equipment other than Sony brand that you want to
control with the TV's remote control, use the following procedures to
program the remote control.
The equipment must have infrared (IR) remote capability in order to be used with this
remote control.
Using the code list below, find the three-digit code number for the
manufacturer of your equipment. (If more than one code number is
listed, use the number listed first.)
2
1
Press repeatedly until the DVD/VCR, SAT/
1
CABLE or i.LINK indicator lights up.
2
Press for five seconds until the
3 indicator of the selected input flashes.
4
3
While the desired indicator is flashing, enter the
three-digit manufacturer's code number.
4
Press .
To check if the code works
Aim your TV's remote control at the equipment, and press
the button. If the equipment responds, the
programming is completed. If not, try the next code listed.
If no code is input within the above specified time, or an invalid or incorrect code
number is input, the remote control automatically goes back to the previous setting.
In some cases, you may not be able to program your remote control to operate other
equipment. In such cases, use the equipment's own remote control.
Removing the batteries or dead batteries may cause the programmed codes to be lost
and revert back to the factory setting. Reprogramming the codes may be necessary.
Review the following chart to determine which diagram to use to connect the components in your system:
Turn off and unplug all components before making connections.
DVD PC
VCR
Player
CableCARD
(optional)
DVD PC
Cable Box
VCR
Player
Satellite Receiver AV Receiver
DVD
Cable Box
VCR
Player
Satellite Receiver
DVD
HD Cable Box Player
AV Receiver
HD Sat Receiver
Digital Recorder
HD Cable Box
DVD
HD Sat Receiver VCR
Player
HD DVR
Cable Box
VCR
Sony
Satellite Receiver
Dream System
Manufacturer's codes Cable Boxes
Manufacturer Code
Instant Replay 308, 309 Manufacturer
DVD Players
JC Penney 304, 305, 309, 314,
Sony
330, 336, 337
Manufacturer Code
Hamlin/Regal
JVC 314, 336, 337, 345,
Sony 751
346, 347
Jerrold/
Sony (i.LINK) 901
Kenwood 314, 332, 336, 337
General Inst./
General Electric 755
LG 332 Motorola
Hitachi 758
LXI (SEARS) 305, 330, 332, 335, Oak
JVC 756 338
Panasonic
Magnavox 757 Magnavox 308, 309, 310
Pioneer
Mitsubishi 761
Marantz 314, 336, 337
Scientific Atlanta
Oritron 759 Marta 332
Tocom
Panasonic 753 Memorex 309, 335
Zenith
Philips 757
Minolta 304, 305
Pioneer 752, 778 Mitsubishi/MGA 323, 324, 325, 326
Satellite Receivers
RCA/PROSCAN 755 Multitech 321, 325, 338
Manufacturer
Samsung 758
NEC 314, 336, 337
Sony
Toshiba 754 Olympic 308, 309
Dish Network
Zenith 760 Optimus 327
Echostar
Orion 317
Laserdisc Players General Electric
Panasonic 306, 307, 308, 309
Hitachi
Pentax 304, 305
Manufacturer Code
Hughes
Philco 308, 309
Sony 701
Mitsubishi
Philips 308, 309, 310
Panasonic 704, 710
Panasonic
Pioneer 308
Pioneer 702
RCA/PROSCAN
Quasar 306, 308, 309
Toshiba
RCA/PROSCAN 304, 305, 308, 309,
VCRs
310, 311, 312, 313,
Manufacturer Code 329
Realistic 309, 324, 328, 330,
Sony 301, 302, 303
335, 338
* If an Aiwa VCR does not
Admiral (M. Ward) 327
Sansui 314
work even though you enter
Aiwa* 338, 344
Samsung 313, 321, 322
Audio Dynamic 314, 337 the code for Aiwa, enter the
Sanyo 330, 335
Broksonic 317, 319
code for Sony instead.
Scott 312, 313, 321, 323,
Canon 308, 309
324, 325, 326, 335
Citizen 332
Sharp 327, 328
Craig 302, 332
Signature 2000 (M.Ward) 327, 338
Criterion 315
SV 2000 338
Curtis Mathes 304, 309, 338
Sylvania 308, 309, 310, 338
Daewoo 309, 312, 341
Symphonic 338
DBX 314, 336, 337
Tashiro 332
Dimensia 304
Tatung 314, 336, 337
Emerson 316, 317, 318, 319,
Teac 314, 336, 337, 338
320, 341
Technics 308, 309
Fisher 330, 335
Toshiba 311, 312
Funai 338
Wards 327, 328, 331, 332,
General Electric 304, 309, 329
335
Go Video 322, 339, 340 Yamaha 314, 330, 336, 337
Goldstar 332
Zenith 331
Hitachi 304, 305, 306, 338
Notes on your new TV
Projection Lamp: Periodic replacement of the projection lamp
Code
will maintain the picture quality.
230
See the "Replacing the Lamp" section of the manual.
222, 223, 224, 225,
226
201, 202, 203, 204,
205, 206, 207, 208, Wide Mode: Selecting the appropriate screen mode will increase
218
enjoyment of your TV viewing.
227, 228, 229
219, 220, 221
211, 214, 215
When watching a Standard Definition source (4:3 aspect
209, 210, 211
216, 217 ratio) on this TV, you will see bars on both the left and right
212, 213
sides of the screen. Press the WIDE button on your remote to
cycle through different screen modes to fill the screen in
Code
various ways. (Wide Zoom enlarges the center, Normal is
801
how your TV receives the signal, Full stretches horizontally
810
810 and Zoom enlarges the image proportionately to fill the
802
screen.)
805
804
809
When watching a High Definition source (16:9 aspect ratio)
803
802, 808 on this TV, you will see the screen filled with an image. Press
806, 807
the WIDE button on your remote to toggle through different
screen modes, especially zooming in to the center of the
screen. (Wide Zoom enlarges the center, Full displays the
image at its original size, Zoom enlarges the image
proportionately to fill the screen.)
When the TV receives a 720p or 1080i formatted signal, the
Normal mode is not available. See the "Using the WIDE
Button" section of the manual.
If you feel the images on the screen are stretched, press the WIDE button to select a
different screen mode.