Advertisement
Quick Links
MoDEL no's 1500hQ, 2000hQ, 2000LQ, 2000LEQ, 3000LQ, 5000LQ
Your new jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
Important: REAd ThESE inSTRuCTiOnS CAREfuLLY. nOTE ThE SAfE OpERATiOnAL REQuiREMEnTS, WARninGS And CAuTiOnS.
uSE ThiS JACK CORRECTLY And WiTh CARE fOR ThE puRpOSE fOR WhiCh iT iS inTEndEd. fAiLuRE TO dO SO MAY CAuSE dAMAGE
And/OR pERSOnAL inJuRY And WiLL invALidATE ThE WARRAnTY. RETAin ThESE inSTRuCTiOnS fOR fuTuRE uSE.
1. SAfETY pRECAuTiOnS
Ensure the jack is in sound condition and good working order. take action for immediate repair or replacement of damaged parts.
Use genuine parts only. The use of improper parts may be dangerous and will invalidate the warranty.
Locate the jack in a suitable, well lit work area.
Keep work area clean and tidy and free from unrelated materials.
use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
Place wedges under wheels of vehicle (but ensure that wheels of jack can freely move).
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or "Park" if automatic).
Ensure minimum distance of 0.5mtr between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.
Ensure there are no passengers in the vehicle.
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
only place jack under those lifting points recommended by vehicle manufacturer (see vehicle handbook).
check the lifting point is stable and centred on the jack saddle.
Ensure the jack wheels are free to move and that there are no obstructions.
DanGEr! Use the jack for lifting only, NOT for supporting the lifted load.
use suitable capacity axle stands under the vehicle before proceeding with any task.
Ensure that there are no persons or obstructions beneath the vehicle before lowering.
use a qualified person to maintain or repair the jack's hydraulic system.
Do not operate the jack if damaged.
Do not allow untrained persons to operate the jack.
Do not exceed the rated capacity of the jack.
Do not allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
Do not jack the vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
Do not work under the vehicle until axle stands have been correctly positioned.
Do not use the jack for purposes other than that for which it is intended.
Do not top up the hydraulic system with brake fluid. use hydraulic jack oil only.
Do not adjust the safety overload valve.
When not in use store jack, fully lowered, in a safe, dry, childproof area.
WARninG! It is very dangerous to go under a vehicle which is supported by a jack even if additional supports are used. Do not go under a
vehicle unless it is supported by adequately rated axle stands.
iMpORTAnT! Ensure that you can see the saddle and jacking point throughout the jacking operation in case there is
any relative movement.
2.
SpECifiCATiOn
Model:
capacity . . . . . . . . . . . . . . . . . . . . . . . . . 1500kg. . . . . . . . . . 2000kg . . . . . . . . . 2000kg . . . . . . . 2000kg . . . . . . . . 3000kg . . . . . . . . . 5000kg
Min. saddle height . . . . . . . . . . . . . . . . . 100mm. . . . . . . . . . 100mm . . . . . . . . . 132mm . . . . . . . . 80mm . . . . . . . . . 95mm . . . . . . . . .165mm
Max. saddle height . . . . . . . . . . . . . . . . 815mm. . . . . . . . . . 780mm . . . . . . . . . 500mm . . . . . . . 375mm . . . . . . . . 508mm . . . . . . . . .565mm
Max. chassis height . . . . . . . . . . . . . . . . 170mm. . . . . . . . . . 200mm . . . . . . . . . 165mm . . . . . . . . 92mm . . . . . . . . 165mm . . . . . . . . .188mm
Length. . . . . . . . . . . . . . . . . . . . . . . . . 1030mm . . . . . . 1050mm . . . . . . . 890mm . . . . . . 860mm . . . . . . .998mm. . . . . . . 1300mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49kg. . . . . . . . . . . . 67kg . . . . . . . . . . . 30kg . . . . . . . . . 42kg . . . . . . . . . . 50kg . . . . . . . . . . . 86kg
3. ASSEMbLY
3.1
1500hQ, 2000hQ, 2000LEQ
3.1.1
Assemble the two-piece handle, using the bolt provided.
3.1.2
Insert the handle into the socket, taking care to ensure that the square indentation at the base of the handle fits correctly over the
square head of the central release shaft.
3.1.3
secure the handle using the bolt provided. Do not over-tighten.
3.2
2000LQ, 3000LQ, 5000LQ
3.2.1
Assemble the two piece handle (3000LQ only), using bolt provided.
3.2.2
Insert the handle into the socket, taking care to ensure that the small metal spigot at the base of the handle slots into the slot provided.
3.2.3
secure the handle using the bolt provided.
1500hQ
2000hQ
Original Language Version
InstructIons for:
TROLLEY JACKS
SupER ROCKET LifT
2000LQ
2000LEQ
1500HQ, 2000HQ, 2000LQ,
2000LEQ, 3000LQ, 5000LQ
3000LQ
5000LQ
Issue: 3 - 31/03/10
Advertisement
Related Manuals for Sealey 1500HQ
Summary of Contents for Sealey 1500HQ
- Page 1 TROLLEY JACKS SupER ROCKET LifT MoDEL no's 1500hQ, 2000hQ, 2000LQ, 2000LEQ, 3000LQ, 5000LQ Your new jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and properly maintained, give you years of trouble free performance.
- Page 2 5.1.3 turn the handle clockwise to close the release valve (1500HQ, 2000HQ & 2000LEQ) or allow the handle to rotate back into its normal position (2000LQ, 3000LQ, 5000LQ) and pump the jack to the required height. the super rocket Lift feature will rapidly raise the saddle to the vehicle lifting point with the minimum of handle strokes.