Table of Contents
Advertisement
Quick Links
Инструкция к сканеру штрих-кода
1: Start .................................................................................................................................. 1
About user manual .............................................................................................................................. 1
Reset default ......................................................................................................................................... 1
Interface mode initialization ............................................................................................................... 1
2: Function mode setting .................................................................................................. 2
About Function mode setting ............................................................................................................ 2
Operating mode ................................................................................................................................... 2
Barcode on/off ...................................................................................................................................... 4
Image reversal ...................................................................................................................................... 5
Lighting settings ................................................................................................................................... 5
Speaker settings .................................................................................................................................. 6
Beeper duration .................................................................................................................................... 6
Dormancy settings ............................................................................................................................... 7
Three-level lighting setting ................................................................................................................. 7
Code reading timeout setting ............................................................................................................ 8
Interface settings .................................................................................................................................. 9
RS232 interface ................................................................................................................................... 9
Data bit ................................................................................................................................................ 10
Stop bit ................................................................................................................................................ 10
Check bit setting ................................................................................................................................ 10
3:Output settings .............................................................................................................. 11
About output settings ....................................................................................................................... 11
Carriage return/line feed setting .................................................................................................... 11
Remove the barcode line at the beginning/end ......................................................................... 11
Set barcode length ........................................................................................................................... 12
Additional code settings .................................................................................................................. 12
Chinese output in keyboard mode ................................................................................................ 13
Poscenter OT 2D
Contents
Advertisement
Table of Contents
Related Manuals for POScenter OT 2D
Summary of Contents for POScenter OT 2D
-
Page 1: Table Of Contents
Инструкция к сканеру штрих-кода Poscenter OT 2D Contents 1: Start ..........................1 About user manual ..........................1 Reset default ............................1 Interface mode initialization ....................... 1 2: Function mode setting ....................2 About Function mode setting ......................2 Operating mode ........................... 2 Barcode on/off ............................ - Page 2 Keyboard language country type ....................13 Analog keyboard ..........................15 Caps lock ............................15 Data Format ............................15 4: Barcode symbology configuration ................16 About Barcode symbology configuration ..................16 Barcode configuration ........................16 Airline 2 of 5 ......................... 16 Aztec Code ...........................
- Page 3 MSI ............................25 PDF417 ..........................25 Pharmacode ......................... 25 QR Code ..........................25 Straight 2 of 5 Industrial ....................26 Telepen ..........................26 Trioptic Code........................26 UPC-A ........................... 26 UPC-E ........................... 27 5: Special function configuration (example) ............... 28 About Special function configuration .................... 28 Only set the prefix and suffix of cross 25 code ................
-
Page 4: 1: Start
1: Start About user manual This user manual includes code system settings, function settings (lighting, keyboard type, and factory reset, etc.) and interface settings. If you need to change the function you need, scan the configuration according to the configuration code below. All bands (*) indicate the factory default value. Reset default Recall Default Read the Version Number... -
Page 5: 2: Function Mode Setting
Function mode setting About Function mode setting In this chapter, you can configure the function mode of the device, including working mode (such as image reversal, etc.), Aimer setting, lighting configuration, LED indicator setting and speaker setting, etc. You only need to scan the corresponding configuration codes as required. - Page 6 Auto scan mode same barcode interval time setting 50ms 100ms 150ms 200ms...
-
Page 7: Barcode On/Off
250ms 300ms Barcode on/off Turn on all barcodes Turn off all barcodes Turn on all one-dimensional codes Turn off all one-dimensional codes Turn on all two-dimensional codes Turn off all two-dimensional codes... -
Page 8: Image Reversal
Image reversal Image reversal *Normal Lighting image settings Enable *Aimer Disable Aimer Enable *Light Disable Light *Led indicator is normal indicator reverse... -
Page 9: Speaker Settings
The LED indicator is always off The LED indicator is always on Speaker settings *Turn on Speaker Turn off Speaker Beeper duration Normal Short 2.7KHz 1.6KHz... -
Page 10: Dormancy Settings
2.0KHz 2.4KHz 3.1KHz 3.5KHz 4.2KHz No sound Dormancy settings 10s Dormancy 100s Dormancy... -
Page 11: Three-Level Lighting Setting
Three-level lighting setting One-level Two-level Three-level Code reading timeout setting 120s 180s 240s 240s... -
Page 12: Interface Settings
Interface settings RS232 interface RS232 baud rate 2400 4800 *9600 19200 38400 57600... -
Page 13: Data Bit
115200 Data bit 7 bits 8 bits Stop bit 2 bits 1 bit Check bit setting... -
Page 14: 3:Output Settings
3: Output settings About output settings This chapter can configure the output of the device, including carriage return/line feed, adding pre/suffix, setting bar code length, removing bar code digits (start/end removal) and multi-country keyboard switching settings, etc. You only need to scan the corresponding configuration code as required. -
Page 15: Set Barcode Length
Set barcode length The length 1 The length is 255 Barcode length lock Additional code settings Enable two additional codes *Disable two additional codes Enable two additional codes Disable two additional codes All UPC/EAN codes must have additional codes No additional code required... -
Page 16: Chinese Output In Keyboard Mode
Chinese output in keyboard mode The keyboard mode can output as Chinese. If you need to output as Chinese, please scan the corresponding configuration code as required. (The default state is no Chinese, but other national languages can be input) *Default Can be used for word, qq, not for excel, notepad Can be used in notepad, excel, not in word... - Page 17 Spanish Singapore Salvador Japan Sierra Leone Turkey Russia Hungary Russian (Russia) Thai...
-
Page 18: Analog Keyboard
Analog keyboard You may need to type your characters in the form of ASCII code. At this time, you can configure the corresponding configuration code to simulate the keyboard as required Enable analog keyboard Disable analog keyboard Turn on the analog keyboard and the front is zero Turn off the analog keyboard and the front is zero Caps lock... -
Page 19: 4: Barcode Symbology Configuration
Barcode symbology configuration About Barcode symbology configuration This chapter can configure the bar code system of the device, including UPC/EAN, Codebar code, Code39, Full ASCII Code39, Interleaved 2 of 5, Code93, UPC-A, GS1 DataBar Omnidirectional, GS1 DataBar Expanded, PDF417, QR Code, Hong Kong 2 of 5 (China post) and Airline 2 of 5 support barcode configuration, you only need to scan the corresponding configuration codes in sequence according to the requirements. -
Page 20: Codablock F
*Disable 5. Codablock F Enable *Disable 6. Code 128 *Enable Disable 7. Code 11 Enable *Disable... -
Page 21: Code 32
8. Code 32 Enable *Disable 9. Code 39 *Enable Disable 10. Code93 Enable *Disable 11. Composite Enable *Disable... -
Page 22: Data Matrix Code
12. Data Matrix Code *Enable Disable 13. EAN/UPC *Enable Disable 14. EAN-8 *Enable Disable Output EAN-8 check digit Disable EAN-8 check digit... -
Page 23: Ean-13
EAN-8 is converted to EAN-13 Prohibit the conversion of EAN-8 to EAN-13 15. EAN-13 *Enable Disable Output EAN-13 check digit Disable EAN-13 check digit 16. Full ASCII Code39 Enable *Disable... -
Page 24: Gs1 Databar Expanded
17. GS1 DataBar Expanded Enable *Disable 18. GS1 DataBar Limited Enable *Disable 19. GS1 DataBar Omnidirectional Enable *Disable... -
Page 25: Hanxin
20. HANXIN Enable *Disable 21. Hong Kong 2 of 5(China post) Enable *Disable Notice: When reading a postal, all other postal need close. 22. Interleaved 2 of 5 *Enable Disable... -
Page 26: Matrix 2 Of 5
23. Matrix 2 of 5 Enable *Disable 24. Maxicode Enable *Disable 25. MicroPDF417 Enable *Disable 26. Micro QR Code Enable *Disable... -
Page 27: Msi
27. MSI Enable *Disable 28. PDF417 *Enable Disable 29. Pharmacode Enable *Disable 30. QR Code *Enable Disable... -
Page 28: Straight 2 Of 5 Industrial
Turn on URL QR code Turn off URL QR code 31. Straight 2 of 5 Industrial Enable *Disable 32. Telepen Enable *Disable 33. Trioptic Code Enable *Disable 34. UPC-A... -
Page 29: Upc-E
*Enable Disable UPC-A output check digit UPC-A does not output check digit Output UPC-A numeric system characters Do not output UPC-A numeric system characters Convert UPC-A to EAN-13 UPC-A is not converted to EAN-13 35. UPC-E *Enable... -
Page 30: 5: Special Function Configuration (Example)
Disable UPC-E does not output check digit UPC-E output check digit *UPC-E does not output header characters UPC-E output header characters UPC-E extended to 12 bits Prohibit UPC-E expansion to 12 bits Special function configuration (example) About Special function configuration This chapter enumerates some configuration examples used by the device, and specifically explains the configuration methods of special functions, which is convenient for users to perform actual operations and familiarize themselves with the... -
Page 31: Scan The Billing Data Code
Turn off Turn off Scan the billing data code Scan the following configuration codes in turn: Can be used in notepad, excel, not in word Turn on Turn off Configure to output only the first 24 characters If the bar code value to be scanned is（986698654666777969696123 test 96969688）... -
Page 32: Web Page Chinese Input Settings
Display all information (need to configure Chinese output configuration)： Default Can be used in notepad, excel, not in word Can be used in word, not in notepad, excel Web page Chinese input settings Scan from top to bottom： Factory settings Utf-8 encoding (can be used for word, not for notepad, excel) Cancel carriage return Cancel line feed... -
Page 33: Attached: Ascii Code Table
Attached: ASCII code table Decimal Characte Decimal Characte Decimal Characte Decimal Characte Ř " & － < > 附：ASCII 码扩展字符（CP-1252 编码） Decimal Characte Decimal Characte Decimal Characte Decimal Characte... -
Page 34: Bytecode Value (Decimal)
€ À Ì ¡ Á Ë ‚ æ Â Í ƒ ç Ã Ï „ ¤ Ä Î … ¥ Å Ð ä Ť Æ æ ‡ è Æ Ñ ˆ ¨ È Ó ‰ © Ç Ò Š ª Ê...
Need help?
Do you have a question about the OT 2D and is the answer not in the manual?
Questions and answers