Advertisement
INSTALLATION MANUAL
INSTALLATION MANUAL
AUTOMATIC WASHER
We congratulate you for your choise. In order to certify the good performance of your Washer, and improve
its life please, follow these instructions.
CHECKING THE INSTALLATION REQUIREMENTS
CHECKING THE INSTALLATION REQUIREMENTS
ELETRIC REQUIREMENTS
Check the
supply
voltage
indicated
on the
label
attached to the
Washer's power cord,
and see if the power
outlet that will be used
for the connection has
D
the same voltage(120V)
Thermal cut-outs or
fuses are required for
the Washer protection.
PREPARING THE WASHER FOR INSTALLATION
PREPARING THE WASHER FOR INSTALLATION
UNPACKING THE WASHER
1. Remove the Washer from the
external packaging. Then
remove the internal
packaging piece and the
accessories bag which are
inside the Washer.
2. Remove the bottom
packagingpiece by lifting
it by the side handles.
Never use the Washer
with the bottom packaging
piece under the machine,
as you may damage it.
INSTALLING THE WASHER
INSTALLING THE WASHER
INSTALL THE WATER OUTLET RUBBER HOSE
Set the curve of the water outlet
rubber hose in the tank, or in a
exclusive draining tube
.
B
IMPORTANT:
The curved end of the water outlet hose must be located between
34 inches and 47 inches. If below34 inches your Washer will not
reach the water level considered adequate for operation. If located
above 47 inches, the Washer will not be able to drain the water.
INSTALL THE WATER INLET HOSE
Please note inside the threaded part the sealing washer
with filter-screen, which must be with the prominent side
of the filter-screen turned outwards.
IMPORTANT:
The filter-screen in that position prevents dirt present
in the water from blocking the filter. Occassionally, it may be
necessary to disconnect the hose from the tap and clean the
filter-screen with a brush and water.
Connect the hose on the tap, sufficiently tight to avoid
water leakage. Open the tap and ckeck if there is leakage in
either end
and
. In case that occurs, tighten again the
A
C
connections
and
.
A
C
IMPORTANT:
Don't conect the Washer hot water inlet to a water source
with temperature above 140F.
TURNING THE WASHER ON
TURNING THE WASHER ON
Do not use plug adapters, extensio cords or improvised connections between the
Washer and the wall outlet. If there is more than one home appliance connected in
the same outlet, there is the risk of a surge and damage may occur to the products.
Ckeck if all the recommendations in the sections 1, 2 and 3 were followed.
Check if the tap and the shutoff valve are open.
Connect the Washer's power cord
If there are no
Phases
thermal cut-outs in
Ground
the power
Wire
distribution panel,
10A
and a exclusive
120V
tripolar power outlet
is not available, seek the aid of an
electrician to install them
(preferably in some place near the
Washer).
ATENTION
Never change the power cord or use it
differently from recommended. If
installation or repair is necessary, call
in an authorized service technician.
3. Remove the plastic
protection from the
cabinet. Over time the
film will become more
difficult to remove, so
it is better to remove it
as you are installing
the washer.
47
inches
34
inches
to the power outlet.
D
The wide diameter of the electric
network must conform to the following
table:
Gauge
12#AWG
10#AWG
8#AWG
Distance
30ft to 39ft
40ft to 65ft
66 to 98ft
from panel
120V
4. Remove the film that
protects the control
panel.
USE THE ADJUSTABLE FEET
TO LEVEL YOUR WASHER
Set the Washer in
its location,
installing it 10cm
away from the
wall, furniture, or
other objects.
Level the Washer
by turning its
rotary feet up or
down,until the surface
of casters is higher
than feet bottom
surface in order to
avoid vibrations.
In order to check if
your Washer is
adequately
laveled, fill it with
water up to the
MIDDLE LEVEL and
see if the water
surface is perfectly
aligned with the
basket holes.
IMPORTANT:
Your Washer was designer with
adjustable feet, which are useful
for the leveling and stability of
the product.
WATER REQUIREMENTS
It is necessary to have
an exclusive tap for the
Washer water inlet
A
The tap should be ¾ BSP
6#AWG
thread.
99 to 164ft
The water pressure
needed filling the Washer
should correspond to a
level of 6ft to 260ft above
the tap (approximately
0,3 PSI to 11 PSI)
LOCATION FOR INSTALLATION
You must install your Washer:
In a location that is not exposed to
direct sunshine or rain.
On a flat, level surface, with
adequate support for all feet. This
will help to avoid vibration, noise
and leakage (see how to level your
Washer on iten 3).
CHECK THE ACESSORIES
Warranty and Autorized Service List.
A
B
TECNICAL DATA
TECNICAL DATA
WATER CONSUPTION
Program
High Level
Super Wash
215 liters
Regular Wash
215 liters
Fast Wash
175 liters
SIZE AND WEIGHT
WITHOUT PACKAGE
Width
22''
Depth
25''
Height with the lid closed
39''
75 lbs
Weight
ELECTRIC FEATURES
Voltage
Voltage
Frequency
Eletric
Range
current
7,3 A
127V
106 to 132V
60 Hz
3,9 A
220V
198 to 242V
60 Hz
GENERAL
Centrifugation (rpm)
750
.
tap
water outlet rubber hose
rubber hose for
C
water inlet
power
D
cord
Medium Level
149 liters
149 liters
129 liters
WITH SHRINK PACKAGE
24''
26''
41''
79 lbs
Maximum
Max. power
power
consumpition
700 W
219 W/h
690 W
213 W/h
Advertisement
