Table of Contents
Advertisement
2 Shipping Inspection
Always transport the unit upright; laying the unit on its side
or top during transit may cause equipment damage. The in-
staller should inspect the product upon receipt for shipping
damage and subsequent investigation is the responsibility
of the carrier. The installer must verify the model number,
specifications, electrical characteristics, and accessories
are correct prior to installation. The distributor or manufac-
turer will not accept claims from dealers for transportation
damage or installation of incorrectly shipped units.
2.1 Parts
Also inspect the unit to verify all required components
are present and intact. Report any missing components
immediately to the manufacturer or to the distributor.
Use only factory authorized replacement parts (see
Section 5). Make sure to include the full product model
number and serial number when reporting and/or ob-
taining service parts.
2.2 Handling
Use caution when transporting / carrying the unit. Do not
move unit using shipping straps. Do not carry unit with
hooks or sharp objects. The preferred method of carry-
ing the unit after arrival at the job site is to carry via a
two-wheel hand truck from the back or sides or via hand
by carrying at the cabinet corners.
3 Codes & Regulations
This product is designed and manufactured to comply with appli-
cable national codes. Installation in accordance with such codes
and / or prevailing local codes / regulations is the responsibility
of the installer. The manufacturer assumes no responsibility for
equipment installed in violation of any codes or regulations.
The United States Environmental Protection Agency
(EPA) has issued various regulations regarding the in-
troduction and disposal of refrigerants. Failure to fol-
low these regulations may harm the environment and
can lead to the imposition of substantial fines. Should
you have any questions please contact the local office of the
EPA and / or refer to EPA's website www.epa.gov.
4 Replacement Parts
When reporting shortages or damages, or ordering repair
parts, give the complete product model and serial numbers
as stamped on the product. Replacement parts for this prod-
uct are available through your contractor or local distributor.
For the location of your nearest distributor consult the white
business pages, the yellow page section of the local tele-
phone book or contact:
HOMEOWNER SUPPORT
GOODMAN MANUFACTURING COMPANY, L.P.
19001 KERMIER ROAD
WALLER, TEXAS 77484
(855) 770-5678
5 Pre-Installation Considerations
5.1 Preparation
Keep this document with the unit. Carefully read all in-
structions for the installation prior to installing product.
Make sure each step or procedure is understood and
any special considerations are taken into account be-
fore starting installation. Assemble all tools, hardware
and supplies needed to complete the installation. Some
items may need to be purchased locally. Make sure ev-
erything needed to install the product is on hand before
starting.
5.2 System Matches
The entire system (combination of indoor and outdoor
sections) must be manufacturer approved and Air-Con-
ditioning, Heating, and Refrigeration Institute (AHRI)
listed. NOTE: Installation of unmatched systems is not
permitted.
5.3 Interconnecting Tubing
Give special consideration to minimize the length of re-
frigerant tubing when installing air handlers. Refer to Re-
mote Cooling / Heat Pump Service Manual RS6200006,
and TP-107 Long Line Set Application R-410A for tubing
guidelines. If possible, allow adequate length of tubing
such that the coil may be removed (for inspection or
cleaning services) from the cabinet without disconnect-
ing the tubing.
5.4 Clearances
The unit clearance from a combustible surface may be
0". However, service clearance must take precedence. A
minimum of 24" in front of the unit for service clearance
is required. Additional clearance on one side or top will
be required for electrical wiring connections. Consult all
appropriate regulatory codes prior to determining final
clearances. When installing this unit in an area that may
become wet (such as crawl spaces), elevate the unit
with a sturdy, non-porous material. In installations that
may lead to physical damage (i.e. a garage) it is advised
to install a protective barrier to prevent such damage.
Always install units such that a positive slope in conden-
sate line (1/4" per foot) is allowed.
5.5 Horizontal Applications
If installed above a finished living space, a secondary
drain pan (as required by many building codes), must be
installed under the entire unit and its condensate drain
line must be routed to a location such that the user will
see the condensate discharge.
6 Installation Location
NOTE: These air handlers are designed for indoor instal-
lation only.
3
Hide quick links:
Advertisement
Table of Contents
