superbrightleds NFLSK-x300X3-UC Instruction Sheet

Important: Read all instructions prior to installation.
Under Cabinet LED
Flexible Light Strip Kit
Parts Included
1 - 16.5' (5m) LED Flexible Light Strip
1 -
Single Color LED Controller - Wireless RF Remote
1 - 12VDC 60W Desktop Power Supply
1 - Female Terminal Screw Adapter
1 - Pigtail CPS Power Adapter Cable
2 - CPS Adapter Cable Clamp-On
4 - Flexible Light Strip Interconnect
3 - Solderless Clamp-On Pigtail Adapter
1 - LC2 Male Power Connector Pigtail
1 - LC2 Female Power Connector Pigtal
10 - 22-16 AWG Grey Wire Nuts
1 - 8' Length 24 AWG Two Conductor Power Wire
8 - Double-Sided Foam Pads
If your installation requires additional parts, visit superbrightleds.com and
enter the part number above in the search box.
Connecting Strips
Gently pull out locking tab on face of Flexible Light Strip
1.
Interconnect (NFLS10-2CSH)
+
-
2. Insert strip fi rmly into Interconnect making sure the polarity is
correct by lining up the + symbol on the strip with the white wire
on the connector.
+
-
3. Return the locking tab to the closed position on the Interconnect
by pushing back in.
+
-
Troubleshooting Tips: If the light strip does not light up, check that the
polairty is correct. + symbol connecting to + symbol on all segments. Make
sure strips are fully inserted in clamp-on connectors.
4400 Earth City Expy
St. Louis, MO 63045
(NFLS-x300X3-UC)
(MCBRF-15A)
(TPZ-1200500A2)
)
(CPS-F2ST
(CPS-PT)
(NFLS10-2CHCPS)
(NFLS10-2CSH)
(NFLS10-2CPTH)
(LC2M-PT)
(LC2F-PT)
(WN-2216)
(WP24-2)
(3M-FTP)
+ + +
- - -
+ + +
- - -
Instruction Sheet
Part Number:
NFLSK-x300X3-UC
Instructions
Pre-test & Confi gure
Remove strip from reel and make connections to power supply
and dimmer (see "Method 1" diagram). Briefl y turn on strip using
dimmer power button to ensure proper operation of the strip,
power supply, dimmer, and remote.
Layout strip on counter below cabinets, hold strips up under
cabinets to determine lengths of strip segments needed for your
installation. See below for cutting instructions.
Connect all strip segments using appropriate length connectors,
see "Connecting Strips" section and "General Diagram" for
guides. Connect strip. Connect strip assembly to power supply
to ensure all segments are connected properly, then remove
power.
Ensure all installation surfaces are clean and dry.
Begin to remove strip's backing while adhering to bottom front
edge of cabinets for optimal illumination. Press fi rmly to secure
strips to surface. Route strip interconnectors under cabinet
seams, windows, and other spaces between cabinets. Attach
dimmer and power supply to desired location using included
foam tape.
Cutting
Cut strips to appropiate length using scissors on lines
indicated with scissor icon. Strip can only be cut on
these lines, which are spaced every 3 LEDs.
(Method 1) With Dimmer
Pigtail CPS Power Adapter Cable
+ -
+ -
Light Strip
Dimmer
(MCBRF-15A)
(Method 2) Without Dimmer
Female Terminal Screw Adapter
(CPS-F2ST)
+
+ -
-
Light Strip
(Method 3) Without Dimmer
CPS Adapter Cable Clamp
(NFLS10-2CHCPS)
+ - + -
Light Strip
(CPS-PT)
+ -
Power Supply
Note: Dimmer must be used between
the light strip and power supply.
Power Supply
Power Supply
5
WA RRANT Y
yr