Clas Ohlson LS9A123-1-01 Quick Start Manual

Extendable RGBW LED Strip Light
Art. no 36-7974 Model LS9A123-1-01
36-7975 LS9A123-2-01
Read the entire instruction manual before use and save it for future reference. We
apologise for any text and picture errors and any changes of technical data. If you have
any questions concerning technical problems please contact our Customer Services.
Safety
Warning:
• Neither the product nor its mains adapter may be dismantled or modified in any
way.
• Never use the product or the mains adapter if it is in any way damaged or
malfunctioning. Unplug the product immediately if it is damaged.
• Do not use the product in environments where explosive or flammable gases are
stored or used.
• The product must only be connected to the included mains adapter.
• Never connect several or other types of devices to the mains adapter.
• The product must not be installed on a wet or electrically conductive surface.
• Make sure that the cables are not damaged whilst the product is being installed.
• Always unplug the mains adapter from the wall socket when the product is not in
use.
• Do not carry the product using the mains lead and do not use it for other
unsuitable purposes.
• Never let children play with the product.
• The product may be used by persons with reduced physical, sensory or mental
capabilities or persons with a lack of experience or knowledge which could
jeopardise their safety, provided they have been instructed in the safe operation of
the product and understand the hazards involved.
Important
• The LEDs cannot be replaced. When the LEDs have reached the end of their
service life, the entire product must be discarded.
• This product is intended only for private use.
Risk of eye damage. Do not look directly at the light source.
The product is not suitable for illuminating a room.
The product is intended for indoor use only.
Class II mains adapter.
Class III strip light
UNITED KINGDOM • CUSTOMER SERVICE tel. 020 8247 9300 e-mail customerservice@clasohlson.co.uk internet www.clasohlson.co.uk
postal Clas Ohlson Ltd, Aquilla House (First floor), 1 Becketts Wharf, Lower Teddington Road, Hampton Wick, Kingston Upon Thames, KT1 4ER
1
Installation
Information
The LED strip light can be mounted using the double-sided adhesive tape (mounted).
For best adhesion, ensure that the surface is clean, dry and free of grease.
The length of the light strip can be adjusted by cutting it at one of the soldering points
which are spaced every 33 cm along its length.
Note: Once the strip light has been cut and shortened, it is no longer possible to
extend it with additional strip lights.
1. Strip light: Remove the protective film from the tape on the back of the light strip
and attach it to a clean, grease-free surface. The strip light may also be screwed
on with plastic clips.
2. Connectors. Connect the strip light and the control box together.
Note: Make sure the strip light is connected in the right way, with the arrows
pointing towards each other. Otherwise the strip light will not work.
3. IR Receiver.
Note: Make sure there are no obstacles between the IR receiver on the LED
control unit and the remote control.
4. Control unit
5. Connection cable: Connect the connection cable to the LED control unit.
6. Mains adapter: Plug the mains adapter into an electrical outlet.
LED strip light extension set
Art. no: 36-7975 (sold separately)
1. Unplug the adapter from the electrical outlet.
2. Remove the protective film from the tape on the back of the strip light and attach
the strip to a clean, grease-free surface. The strip light may also be screwed on
with plastic clips.
3. Connect the strip lights together with one another.
Note: Make sure the strip light is connected in the right way. Otherwise the strip
light will not work.
4
2 3
Remote control
1. 12 colour tones within the RGB spectrum
2. [ R ] Red light
[ G ] Green light
[ B ] Blue light
[ W ] White light
3. [ ] Increase light intensity
[ ] Decrease light intensity
4. [ OFF ] Turn the strip light off
[ ON ] Turn the strip light on
5. [ FLASH ] Change slowly between all the colours
6. [ STROBE ] Change quickly between all the colours
7. [ FADE ] Change between all the colours, the
colours fade into one another
8. [ SMOOTH ] Change between all colours with no visible transition
Care and maintenance
• Unplug the mains lead from the wall socket before cleaning.
• The product should be cleaned using a dry cloth or vacuum cleaner.
Responsible disposal
This symbol indicates that the product should not be disposed of with
general household waste. This applies throughout the entire EU. In order
to prevent any harm to the environment or health hazards caused by
incorrect waste disposal, the product must be handed in for recycling
so that the material can be disposed of in a responsible manner. When
recycling your product, take it to your local collection facility or contact the
place of purchase. They will ensure that the product is disposed of in an
environmentally sound manner.
Specifications
Mains adapter
230 V AC, 50/60 Hz
Power supply
Output 24 V DC, 1 A, 24 W
Strip light
36-7974 36-7975
Dimensions 6000 x 10 mm Dimensions
Light source 324 x LED Light source
Remote control
Range Max 7 m from straight ahead, 3 m from the sides.
Battery 1 x CR2025 (included)
5
6
3
4
2
5
1
6
7
8
3000 x 10 mm
162 x LED